Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0074558 REAR VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


a.

Disconnect the T6 connector from the rear television camera assembly.

E220918N10
3.406,0.104 3.802,0.344 0.396,0.24 3.531,0.135 3.802,0.365 0.271,0.229 10 false T6


b.

Measure the voltage of each terminal of the wire harness side connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T6-6 (CB+) - Body ground B - Body ground Power source Within 60 seconds of turning the ignition switch ACC 5.5 to 7.05 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the T6 connector to the rear television camera assembly.


d.

Check for pulses between each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T6-3 (CV+) - T6-2 (CV-) W - R Video signal Ignition switch ON
Shift lever in R
Camera lens not covered, displaying an image
Pulse generation
(See waveform 1)
Ignition switch ON
Shift lever in R
Camera lens covered, blacking out screen
Pulse generation
(See waveform 2)

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


If the result is not as specified, the camera may have a malfunction.


e.
E265836C07
0.625,4.469 0.781,4.469 0.781,4.469 0.969,3.781 false 1.438,4.479 1.302,4.479 1.302,4.479 1.115,3.708 false 0.677,2.292 0.813,2.292 0.813,2.292 0.938,1.719 false 1.396,2.271 1.25,2.271 1.25,2.271 1.063,1.594 false 0.208,0.156 0.521,0.354 0.313,0.198 10 *a 0.51,2.208 0.823,2.406 0.313,0.198 10 *c 0.229,2.385 0.542,2.583 0.313,0.198 10 *b 1.427,2.198 1.74,2.396 0.313,0.198 10 *d 0.469,4.375 0.781,4.573 0.313,0.198 10 *c 1.479,4.396 1.792,4.594 0.313,0.198 10 *d 0.115,3.323 0.51,3.51 0.396,0.188 10 GND 0.083,1.063 0.479,1.25 0.396,0.188 10 GND
*a Waveform 1 (camera lens not covered, displaying an image)
*b Waveform 2 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Terminal No. (Symbol) T6-3 (CV+) - T6-2 (CV-)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Terminal No. (Symbol) T6-3 (CV+) - T6-2 (CV-)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.