Home › Power Source / Network › 2GR-FE BATTERY / CHARGING › GENERATOR
RM2030EQ _57 Power Source / Network _014661 2GR-FE BATTERY / CHARGING _0074570 GENERATOR A

2GR-FE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A128081N02
0.363,0.43 0.661,0.576 0.299,0.146 10 SST 1.389,0.7 0.711,0.559 0.711,0.559 1.23,1.129 false

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A137712C01
2.583,1.052 1.927,0.771 true 2.542,1.531 1.896,1.833 true 1.74,1.76 1.927,1.906 0.188,0.146 10 false *b 1.771,0.667 2.031,0.906 0.26,0.24 10 false *a
*a Tab
*b Cutout


Fit the tabs on the retainer plate into the cutouts on the generator drive end frame to install the retainer plate.


c.

Install the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the drive end frame on the generator pulley with clutch.


b.
A293821

Install the generator rotor assembly to the generator drive end frame.


Hide 27415 3.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Temporarily install the generator pulley with clutch onto the rotor shaft.


b.

Mount the generator drive end frame in a vise tightly.


c.
A292398C01
1.188,0.635 0.781,0.635 false 0.906,1.729 0.552,1.729 false 0.604,0.552 0.917,0.708 0.313,0.156 10 *1 0.385,1.646 0.698,1.802 0.313,0.156 10 *2
*1 SST (A)
*2 SST (B)


Confirm SST (A) and (B) shown in the illustration.

SST
09820-63021  


d.
A185232C01
2.063,0.698 1.708,0.313 1.708,0.313 1.552,0.313 true 2.344,2.156 2.771,2.448 2.771,2.448 2.99,1.063 true 1.354,0.24 1.552,0.563 0.198,0.323 10 false *1 2.719,2.469 3,2.708 0.281,0.24 10 false *2
*1 Rotor Shaft
*2 SST (A)


Place the rotor shaft end into SST (A).


e.
A185233C01
0.896,2.24 0.646,2.24 false 2.906,1.219 2.906,1.698 true 2.344,2.156 2.729,2.375 false 1.625,0.344 2.323,0.344 true 1.469,0.26 1.771,0.646 0.302,0.385 10 false *1 2.76,2.333 3,2.677 0.24,0.344 10 false *3 0.479,2.177 0.656,2.542 0.177,0.365 10 false *2 2.844,1.719 3.021,2.083 0.177,0.365 10 false *2
*1 Generator Pulley with Clutch
*2 SST (B)
*3 SST (A)


Fit SST (B) to the generator pulley with clutch.


f.
A292400C01
2.625,1.427 2.813,1.042 2.813,1.042 3,1.042 false 2.01,1.542 1.354,1.542 false 1.177,1.479 1.49,1.635 0.313,0.156 10 *1 3.031,0.969 3.344,1.125 0.313,0.156 10 *2 3.073,1.646 3.385,1.802 0.313,0.156 10 *a 2.26,2.125 2.573,2.281 0.313,0.156 10 *b
*1 SST (B)
*2 SST (A)
*a Fulcrum Length
100 mm (3.94 in.)
*b Fulcrum Length
255 mm (10.04 in.)


Tighten the pulley by turning SST (B) in the direction shown in the illustration.

Torque:
without SST : 80 N*m (816 kgf*cm, 59 ft.*lbf)
with SST : 57 N*m (581 kgf*cm, 42 ft.*lbf)

NOTICE:
·

The "with SST" torque value is effective when using SST with a fulcrum length of 100 mm (3.94 in.) and a torque wrench with a fulcrum length of 255 mm (10.04 in.) (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

The "with SST" torque value is effective when SST is parallel to the torque wrench.

·

Check that the drive end frame is secured in the vise tightly.

·

Hold SST (A) tightly during the operation.




g.

Remove SST from the generator assembly.


h.

Check that the generator pulley with clutch rotates smoothly.


i.

Install a new generator pulley cap to the generator pulley with clutch.


Hide 27360 4.INSTALL GENERATOR COIL ASSEMBLY

a.
A293820

Place a new generator washer on the generator rotor.


b.
A128082C02
1.656,0.615 1.344,0.302 1.344,0.302 1.219,0.302 false 1.042,0.229 1.219,0.552 0.177,0.323 10 *1
*1 Deep Socket Wrench (21 mm)


Using a deep socket wrench (21 mm) and a press, slowly press in the generator coil assembly.


c.
A128074

Install the 4 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 27370 5.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A079315C02
0.927,0.51 0.719,0.188 0.719,0.188 2.469,0.74 false 0.563,0.083 0.813,0.25 0.25,0.167 10 false *1
*1 Pin


While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the brush holder hole.


b.
A079316C01
1.688,0.969 1.646,1.156 false 1.542,1.177 1.729,1.354 0.188,0.177 10 *1
*1 Pin


Install the generator brush holder assembly to the generator coil with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder.


Hide 27387B 6.INSTALL GENERATOR TERMINAL INSULATOR

a.
A292399

Install the generator terminal insulator to the generator coil.

NOTICE:

Be sure to install the terminal insulator in the correct direction.



Hide 27039 7.INSTALL GENERATOR REAR END COVER

a.
A128071

Install the generator rear end cover to the generator coil with the 3 nuts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)