OVERALL CAN BUS DIAGRAM (for LHD)
Control system CAN is composed of 2 buses.
| *A | for Navigation receiver type | *B | for Radio and display type |
| *C | w/ AFS | *D | w/ Toyota parking assist-sensor system |
| *E | w/ Seat position memory | - | - |
| *1 | V Bus | *2 | Sub Bus 1 |
| *3 | V Bus Terminating Resistor | *4 | Sub Bus 1 Terminating Resistor |
| *5 | Combination Meter Assembly
(for V Bus) |
*6 | Main Body ECU (Multiplex Network Body ECU)
(for V Bus and Sub Bus 2) |
| *7 | Airbag Sensor Assembly
(for V Bus) |
*8 | DLC3
(for V Bus) |
| *9 | Power Steering ECU Assembly
(for V Bus) |
*10 | Steering Sensor
(for V Bus) |
| *11 | AFS ECU
(for V Bus) |
*12 | Air Conditioning Amplifier Assembly
(for V Bus) |
| *13 | Smart Key ECU Assembly
(Certification ECU) (for V Bus) |
*14 | Brake Actuator Assembly
(for V Bus) |
| *15 | ·
Navigation ECU Sub-assembly ·
Radio and Display Receiver Assembly (for V Bus) |
*16 | Clearance Warning ECU Assembly
(for V Bus) |
| *17 | ECM
(for V Bus) |
*18 | Position Control ECU and Switch Assembly (for Driver Side)
(for Sub Bus 1) |
| *19 | Outer Mirror Control ECU Assembly
(for Driver Side) (for Sub Bus 1) |
*20 | Outer Mirror Control ECU Assembly (for Front Passenger Side) |
| *21 | CAN No. 5 J/C
(for Sub Bus 1) |
- | - |
The main body ECU (multiplex network body ECU) functions as a gateway between the V bus and sub bus 1.
Refer to the following bus wiring diagrams for details.
V BUS (for LHD)
The CAN communication system connects to other network via ECUs that function as a gateway.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
OVERALL CAN BUS DIAGRAM (for RHD)
Control system CAN is composed of 3 buses.
| *A | for Navigation Receiver Type | *B | for Radio and Display Type |
| *C | w/ Smart Entry and Start System | *D | w/ Seat Position Memory |
| *E | w/ Blind Spot Monitor System | *F | w/ AFS |
| *G | w/ Toyota Parking Assist-sensor System | - | - |
| *1 | V Bus | *2 | Sub Bus 1 |
| *3 | Sub Bus 2 | *4 | V Bus Terminating Resistor |
| *5 | Sub Bus 1 Terminating Resistor | *6 | Sub Bus 2 Terminating Resistor |
| *7 | ECM
(for V Bus) |
*8 | Main Body ECU
(Multiplex Network Body ECU) (for V Bus and Sub Bus 1) |
| *9 | Airbag Sensor Assembly
(for V Bus) |
*10 | Air Conditioning Amplifier Assembly
(for V Bus) |
| *11 | Power Steering ECU Assembly
(for V Bus) |
*12 | ·
Navigation ECU Sub-assembly ·
Radio and Display Receiver Assembly (for V Bus) |
| *13 | Network Gateway ECU
(for V Bus and Sub Bus 2) |
*14 | Smart Key ECU Assembly (Certification ECU)
(for V Bus) |
| *15 | Steering Sensor
(for V Bus) |
*16 | DLC3
(for V Bus) |
| *17 | Brake Actuator Assembly
(for V Bus) |
*18 | AFS ECU
(for V Bus) |
| *19 | Clearance Warning ECU Assembly
(for V Bus) |
*20 | Combination Meter Assembly
(for V Bus) |
| *21 | Outer Mirror Control ECU Assembly
(for Front Passenger Side) (for Sub Bus 1) |
*22 | Outer Mirror Control ECU Assembly
(for Driver Side) (for Sub Bus 1) |
| *23 | Position Control ECU and Switch Assembly (for Driver Side)
(for Sub Bus 1) |
*24 | CAN No. 4 J/C
(for Sub Bus 1) |
| *25 | Blind Spot Monitor Sensor RH
(for Sub Bus 2) |
*26 | Blind Spot Monitor Sensor LH
(for Sub Bus 2) |
| *27 | CAN No. 7 J/C
(for Sub Bus 2) |
- | - |
The main body ECU (multiplex network body ECU) functions as a gateway between the V bus and sub bus 1.
The network gateway ECU functions as a gateway between the V bus and sub bus 2.
Refer to the following bus wiring diagrams for details.
V BUS (for RHD)
The CAN communication system connects to other networks via ECUs that function as a gateway.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
SUB BUS 1 (for LHD) (w/ Seat Position Memory)
SUB BUS 1 (for RHD) (w/ Seat Position Memory)
SUB BUS 2 (for RHD) (w/ Blind Spot Monitor System)