Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2012.02–2015.04
RM2030EQ _57 Power Source / Network _014663 NETWORKING _0074573 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Gateway ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Gateway ECU Communication Stop Mode Either condition is met:
·

"CAN Gateway1" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Gateway ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Network gateway ECU branch line or connector

·

Power source circuit of network gateway ECU

·

Network gateway ECU ground circuit

·

Network gateway ECU



WIRING DIAGRAM

C248829E03
1.667,0.521 1.885,0.521 1.885,0.521 2.156,1.115 false 3.844,1.094 4.146,0.49 4.146,0.49 4.302,0.49 false 2.833,0.396 3.333,0.656 0.5,0.26 10 false DLC3 3.563,4.583 4.49,4.896 0.927,0.313 10 false Trouble Area 6.333,2.635 6.792,2.875 0.458,0.24 10 false ECM 0.448,2.646 1.625,3.094 1.177,0.448 10 false Combination Meter Assembly 0.417,0.427 1.635,0.896 1.219,0.469 10 false CAN No. 2 Junction Connector 6.167,2.042 6.594,2.271 0.427,0.229 10 false 120 Ω 0.698,2.021 1.156,2.271 0.458,0.25 10 false 120 Ω 1.438,4.99 3.469,5.292 2.031,0.302 10 false : CAN Main Bus Line (CANH) 1.448,5.396 3.417,5.677 1.969,0.281 10 false : CAN Main Bus Line (CANL) 4.427,4.99 6.302,5.25 1.875,0.26 10 false : CAN Branch Line (CANH) 4.417,5.396 6.292,5.688 1.875,0.292 10 false : CAN Branch Line (CANL) 3.76,4.167 5.427,4.458 1.667,0.292 10 false Network Gateway ECU 3.875,3.104 4.385,3.333 0.51,0.229 10 false CA1H 4.375,3.104 4.865,3.333 0.49,0.229 10 false CA1L 3.906,2.896 4.167,3.104 0.26,0.208 10 false 16 4.531,2.906 4.75,3.104 0.219,0.198 10 false 15 4.375,0.396 6.365,0.625 1.99,0.229 10 false CAN No. 1 Junction Connector 3.438,4.167 3.875,4.406 0.438,0.24 10 false I160 3.625,3.573 3.969,3.771 0.344,0.198 10 false IG1 3.625,3.844 3.969,4.052 0.344,0.208 10 false IG2 3.417,3.5 3.635,3.74 0.219,0.24 10 false 10 3.458,3.76 3.635,3.979 0.177,0.219 10 false 9 5.052,3.323 5.323,3.594 0.271,0.271 10 false 4 4.677,3.406 5.135,3.656 0.458,0.25 10 false GND 5.979,2.635 6.333,2.885 0.354,0.25 10 false A25 0.188,2.635 0.5,2.896 0.313,0.26 10 false I18 0.094,0.042 1.656,0.344 1.563,0.302 12 false V Bus (for RHD): 3.458,3.25 3.74,3.479 0.281,0.229 10 false 2 2.167,3.469 3.208,3.719 1.042,0.25 10 false ECU-B NO. 1 2.156,3.719 3.219,3.979 1.063,0.26 10 false ECU-IG1 NO. 1 2.156,4.031 3.198,4.229 1.042,0.198 10 false ECU-IG2 NO. 2 3.625,3.323 4.01,3.552 0.385,0.229 10 false BATT

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 11.84 seconds, and then drive the vehicle at a speed of 6 km/h (4 mph) or more at least 6 seconds. Check that the warning light remains off after turning off following the initial light check.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (NETWORK GATEWAY ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the network gateway ECU connector.


c.
C238892C34
0.438,1.156 0.844,1.396 0.406,0.24 2.188,1.5 2.188,1.865 2.188,1.865 2.042,1.865 false 2.313,1.5 2.313,1.875 2.313,1.875 2.469,1.875 false 0.104,0.125 0.406,0.458 0.302,0.333 10 false *a 2.521,1.781 3.042,2 0.521,0.219 10 false CA1H 1.667,1.781 2.125,1.979 0.458,0.198 10 false CA1L 0.51,1.198 0.906,1.438 0.396,0.24 10 false I160
*a Front view of wire harness connector
(to Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
I160-16 (CA1H) - I160-15 (CA1L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NETWORK GATEWAY ECU)

2.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C238892C35
0.427,1.135 0.833,1.375 0.406,0.24 2.188,1.281 2.188,0.615 2.188,0.615 2.354,0.615 false 0.125,0.135 0.458,0.521 0.333,0.385 10 false *a 2.438,0.531 2.885,0.792 0.448,0.26 10 false GND 0.5,1.177 0.854,1.438 0.354,0.26 10 false I160
*a Front view of wire harness connector
(to Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
I160-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND TERMINAL)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Connect the cable to the negative (-) battery terminal.


b.
C238892C36
0.219,1.104 0.667,1.333 0.448,0.229 1.469,1.51 1.469,1.896 1.469,1.896 1.281,1.896 false 1.594,1.5 1.594,1.896 1.594,1.896 1.781,1.896 false 1.229,1.281 1.229,0.656 1.229,0.656 0.844,0.656 false 0.094,0.125 0.344,0.365 0.25,0.24 10 false *a 1.844,1.813 2.302,2.01 0.458,0.198 10 false IG1 1,1.823 1.458,2.021 0.458,0.198 10 false IG2 0.333,1.135 0.667,1.333 0.333,0.198 10 false I160 0.438,0.583 0.896,0.781 0.458,0.198 10 false BATT
*a Front view of wire harness connector
(to Network Gateway ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Value
I160-2 (BATT) - Body ground Ignition switch off 11 to 14 V
I160-9 (IG2) - Body ground Ignition switch ON 11 to 14 V
I160-10 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)