Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2030EQ _57 Power Source / Network _014663 NETWORKING _0074573 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Certification ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Certification ECU Communication Stop Mode Either condition is met:
·

"Certification (Smart)" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Certification ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Smart key ECU assembly (Certification ECU) branch line or connector

·

Power source circuit of smart key ECU assembly (certification ECU)

·

Smart key ECU assembly (Certification ECU) ground circuit

·

Smart key ECU assembly (Certification ECU)



WIRING DIAGRAM

C241176E19
1.74,0.688 1.958,0.688 1.958,0.688 2.271,1.281 false 3.844,1.281 4.146,0.688 4.146,0.688 4.302,0.688 false 2.823,0.583 3.344,0.927 0.521,0.344 10 false DLC3 3.646,4.635 4.594,4.99 0.948,0.354 10 false Trouble Area 6.313,2.823 6.719,3.042 0.406,0.219 10 false ECM 0.417,2.823 1.594,3.302 1.177,0.479 10 false Combination Meter Assembly 0.469,0.594 1.708,1.042 1.24,0.448 10 false CAN No. 1 Junction Connector 6.198,2.219 6.677,2.5 0.479,0.281 10 false 120 Ω 0.677,2.219 1.229,2.531 0.552,0.313 10 false 120 Ω 1.448,4.979 3.365,5.313 1.917,0.333 10 false : CAN Main Bus Line (CANH) 1.448,5.385 3.365,5.719 1.917,0.333 10 false : CAN Main Bus Line (CANL) 4.417,4.99 6.198,5.323 1.781,0.333 10 false : CAN Branch Line (CANH) 4.417,5.396 6.115,5.729 1.698,0.333 10 false : CAN Branch Line (CANL) 2.854,4.208 5.708,4.417 2.854,0.208 10 false Smart Key ECU Assembly (Certification ECU) 3.917,3.281 4.396,3.458 0.479,0.177 10 false CANH 4.385,3.281 4.844,3.458 0.458,0.177 10 false CANL 3.635,3.427 3.927,3.615 0.292,0.188 10 false +B 3.646,3.802 3.958,4.052 0.313,0.25 10 false IG 4.854,3.615 5.042,3.823 0.188,0.208 10 false E 3.896,2.854 4.115,3.063 0.219,0.208 10 false 14 4.531,2.854 4.854,3.125 0.323,0.271 10 false 15 5.104,3.396 5.344,3.656 0.24,0.26 10 false 11 3.375,3.229 3.573,3.469 0.198,0.24 10 false 2 3.354,3.615 3.531,3.802 0.177,0.188 10 false 5 2.635,3.563 3.052,3.833 0.417,0.271 10 false AM2 2.49,4.021 3.542,4.271 1.052,0.25 10 false ECU-IG2 NO. 2 4.438,0.604 6.552,0.896 2.115,0.292 10 false CAN No. 2 Junction Connector 3.281,3.427 3.573,3.656 0.292,0.229 10 false A43 4.406,3.073 4.688,3.323 0.281,0.25 10 false I78 4.01,3.073 4.26,3.302 0.25,0.229 10 false I78 3.302,3.813 3.615,4.073 0.313,0.26 10 false I78 5.063,3.615 5.458,3.865 0.396,0.25 10 false A43 0.115,0.188 1.479,0.531 1.365,0.344 12 false V Bus (for LHD): 0.125,2.823 0.5,3.104 0.375,0.281 10 false I18 6,2.823 6.479,3.104 0.479,0.281 10 false A25

C244444E10
1.552,0.688 1.771,0.688 1.771,0.688 2.083,1.281 false 3.875,1.281 4.177,0.688 4.177,0.688 4.333,0.688 false 3.25,0.583 3.844,0.917 0.594,0.333 10 false DLC3 3.677,4.604 4.615,4.99 0.938,0.385 10 false Trouble Area 0.854,2.844 1.333,3.135 0.479,0.292 10 false ECM 0.271,0.594 1.5,1.104 1.229,0.51 10 false CAN No. 1 Junction Connector 6.208,2.229 6.656,2.469 0.448,0.24 10 false 120 Ω 0.698,2.219 1.208,2.573 0.51,0.354 10 false 120 Ω 1.469,4.979 3.385,5.313 1.917,0.333 10 false : CAN Main Bus Line (CANH) 1.469,5.385 3.385,5.719 1.917,0.333 10 false : CAN Main Bus Line (CANL) 4.438,4.99 6.219,5.323 1.781,0.333 10 false : CAN Branch Line (CANH) 4.438,5.406 6.135,5.74 1.698,0.333 10 false : CAN Branch Line (CANL) 2.948,4.177 5.802,4.385 2.854,0.208 10 false Smart Key ECU Assembly (Certification ECU) 4.01,3.271 4.49,3.521 0.479,0.25 10 false CANH 4.479,3.271 4.969,3.469 0.49,0.198 10 false CANL 3.75,3.458 4.063,3.677 0.313,0.219 10 false +B 3.76,3.813 4.01,4.031 0.25,0.219 10 false IG 4.979,3.615 5.125,3.792 0.146,0.177 10 false E 3.865,3.073 4.104,3.323 0.24,0.25 10 false 14 4.844,3.083 5.052,3.323 0.208,0.24 10 false 15 5.208,3.417 5.438,3.656 0.229,0.24 10 false 11 3.51,3.281 3.688,3.531 0.177,0.25 10 false 2 3.51,3.646 3.635,3.823 0.125,0.177 10 false 5 2.604,3.615 2.969,3.885 0.365,0.271 10 false AM2 2.448,3.979 3.469,4.208 1.021,0.229 10 false ECU-IG2 NO. 2 4.448,0.604 6.604,0.938 2.156,0.333 10 false CAN No. 2 Junction Connector 0.125,0.167 1.604,0.563 1.479,0.396 12 false V Bus (for RHD): 5.906,2.865 7.094,3.323 1.188,0.458 10 false Combination Meter Assembly 5.667,2.865 6,3.167 0.333,0.302 10 false I18 0.51,2.844 0.854,3.073 0.344,0.229 10 false A25 5.167,3.615 5.5,3.823 0.333,0.208 10 false A43 4.135,3.083 4.469,3.292 0.333,0.208 10 false I78 4.542,3.083 4.875,3.292 0.333,0.208 10 false I78 3.458,3.813 3.792,4.021 0.333,0.208 10 false I78 3.417,3.469 3.75,3.677 0.333,0.208 10 false A43

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure (w/o blind spot monitor system): Turn the ignition switch to ON, wait at least 20 seconds, and then drive the vehicle at a speed of 6 km/h (4 mph) or more at least 6 seconds. Check that the warning light remains off after turning off following the initial light check.

·

DTC check procedure (w/ blind spot monitor system): Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 20 seconds, and then drive the vehicle at a speed of 6 km/h (4 mph) or more at least 6 seconds. Check that the warning light remains off after turning off following the initial light check.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (SMART KEY ECU ASSEMBLY (CERTIFICATION ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the smart key ECU assembly (certification ECU) connector.


c.
C240536C01
0.292,1.583 0.75,1.865 0.458,0.281 1.281,0.688 1.49,0.688 1.49,0.688 1.49,1.719 false 1.771,0.688 1.583,0.688 1.583,0.688 1.583,1.708 false 0.125,0.073 0.333,0.26 0.208,0.188 10 *a 0.771,0.573 1.219,0.76 0.448,0.188 10 CANL 1.813,0.573 2.26,0.76 0.448,0.188 10 CANH 0.427,1.635 0.75,1.802 0.323,0.167 10 I78
*a Rear view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I78-14 (CANH) - I78-15 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (SMART KEY ECU ASSEMBLY (CERTIFICATION ECU))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C240538C01
0.438,1.115 0.896,1.396 0.458,0.281 0.219,2.938 0.677,3.219 0.458,0.281 2.24,1.25 2.563,1.25 false 0.885,0.938 1.188,0.938 false 0.917,2.115 1.125,2.115 1.125,2.115 1.125,2.917 false 0.135,0.052 0.354,0.25 0.219,0.198 10 false *a 0.646,0.854 0.865,1.031 0.219,0.177 10 false +B 0.688,2.021 0.875,2.208 0.188,0.188 10 false IG 2.604,1.167 2.75,1.354 0.146,0.188 10 false E 0.531,1.156 0.854,1.323 0.323,0.167 10 false A43 0.354,2.99 0.677,3.156 0.323,0.167 10 false I78
*a Rear view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-11 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-2 (+B) - Body ground Ignition switch off 11 to 14 V
I78-5 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)