Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2012.02–2015.04
RM2030EQ _57 Power Source / Network _014663 NETWORKING _0074573 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0232 Lost Communication with Blind Spot Monitor Slave Module No communication from the blind spot monitor sensor LH continues.
·

Blind spot monitor sensor LH branch line or connector

·

Power source circuit of blind spot monitor sensor LH

·

Blind spot monitor sensor LH ground circuit

·

Blind spot monitor sensor LH


The network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2.

HINT:

This diagnosis procedure is for when DTC U0232 is output by the network gateway ECU (Intelligent tester display: Gateway).


WIRING DIAGRAM

C240760E12
1.271,0.583 1.615,0.365 1.615,0.365 1.792,0.365 false 4,0.583 4.271,0.313 4.271,0.313 4.448,0.313 false 4.531,2.094 4.531,2.99 4.531,2.99 4.792,2.99 false 0.688,1.49 1.083,1.635 0.396,0.146 10 false 120 Ω 5.875,2.115 7.01,2.479 1.135,0.365 10 false Network Gateway ECU 6.146,1.49 6.542,1.635 0.396,0.146 10 false 120 Ω 2.188,2.75 2.646,2.896 0.458,0.146 10 false CA1P 1.938,4.292 3.844,4.469 1.906,0.177 10 false Blind Spot Monitor Sensor LH 4.219,4.375 5.125,4.563 0.906,0.188 10 false Trouble Area 2.281,2.563 2.531,2.708 0.25,0.146 10 false 8 2.917,2.563 3.177,2.708 0.26,0.146 10 false 4 2.052,3.958 2.479,4.146 0.427,0.188 10 false BLGD 2.042,3.354 2.354,3.531 0.313,0.177 10 false BLB 2.74,2.75 3.198,2.896 0.458,0.146 10 false CA1N 1.125,5 3.156,5.177 2.031,0.177 10 false : CAN Main Bus Line (CANH) 1.125,5.396 3.156,5.573 2.031,0.177 10 false : CAN Main Bus Line (CANL) 4.271,5 5.99,5.177 1.719,0.177 10 false : CAN Branch Line (CANH) 4.271,5.396 5.969,5.573 1.698,0.177 10 false : CAN Branch Line (CANL) 4.75,0.25 6.917,0.479 2.167,0.229 10 false CAN No. 6 Junction Connector 2.094,0.302 4.063,0.49 1.969,0.188 10 false CAN No. 7 Junction Connector 1.813,0.302 2.094,0.49 0.281,0.188 10 false T18 4.469,0.25 4.75,0.438 0.281,0.188 10 false T17 5.135,2.927 7.083,3.104 1.948,0.177 10 false CAN No. 5 Junction Connector 0.854,3.51 1.906,3.688 1.052,0.177 10 false ECU-IG1 NO. 3 1.646,4.292 1.948,4.469 0.302,0.177 10 false T16 1.885,3.844 2.01,4.021 0.125,0.177 10 false 1 1.896,3.25 2.031,3.427 0.135,0.177 10 false 5 4.823,2.917 5.135,3.104 0.313,0.188 10 false O31 5.563,2.115 5.906,2.302 0.344,0.188 10 false I160 0.042,0.01 1.677,0.208 1.635,0.198 12 false Sub Bus 2 (for RHD):

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 22 seconds, and then drive the vehicle at a speed of 5 km/h (3 mph) or more.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

Body Electrical > Gateway > Trouble Codes
50001 150
HINT:

If DTC U1002 is output from Gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.



Result:
Result Proceed to
U1002 is not output from network gateway ECU
(Intelligent tester display: Gateway)
A
U1002 is output from network gateway ECU
(Intelligent tester display: Gateway)
B



A

2.CHECK FOR OPEN IN SUB BUS 2 LINES (BLIND SPOT MONITOR SENSOR LH BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 2 LINES (BLIND SPOT MONITOR SENSOR LH BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the blind spot monitor sensor LH connector.


c.
C240531C09
0.406,1.615 0.927,1.927 0.521,0.313 2.042,1.771 2.563,1.771 false 1.99,1.969 1.99,2.563 1.99,2.563 2.177,2.563 false 0.125,0.063 0.333,0.26 0.208,0.198 10 false *a 2.615,1.688 3.063,1.875 0.448,0.188 10 false CA1N 2.219,2.49 2.646,2.677 0.427,0.188 10 false CA1P 0.51,1.688 0.885,1.865 0.375,0.177 10 false T16
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T16-8 (CA1P) - T16-4 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH)

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C240531C10
0.427,1.479 0.948,1.792 0.521,0.313 1.49,1.781 0.927,2.271 false 0.125,0.063 0.333,0.26 0.208,0.198 10 false *a 0.448,2.219 0.896,2.406 0.448,0.188 10 false BLGD 0.531,1.552 0.906,1.729 0.375,0.177 10 false T16
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T16-1 (BLGD) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Connect the cable to the negative (-) battery terminal.


b.
C240531C11
0.417,1.604 0.938,1.917 0.521,0.313 1.521,1.979 1.521,2.573 1.521,2.573 1.333,2.573 false 0.125,0.063 0.333,0.26 0.208,0.198 10 false *a 0.99,2.479 1.333,2.667 0.344,0.188 10 false BLB 0.542,1.677 0.917,1.854 0.375,0.177 10 false T16
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T16-5 (BLB) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)