Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2030EQ _57 Power Source / Network _014663 NETWORKING _0074573 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U1002  Lost Communication with Gateway Module (Main Body ECU)  


DESCRIPTION

·

The main body ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 1.

·

When the main body ECU receives a response signal from the ECUs connected to sub bus 1, the main body ECU recognizes and memorizes that the ECU is connected to sub bus 1. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to sub bus 1 when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 1, the main body ECU determines that a malfunction exists.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U1002 Lost Communication with Gateway Module (Main Body ECU) Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 1.
·

Open or short in Sub bus 1 main line or connector

·

Open or short in Sub bus 1 branch line or connector

·

Main body ECU (Multiplex network body ECU)

·

Outer mirror control ECU assembly (for Driver side)

·

Outer mirror control ECU assembly (for Front passenger side)

·

Position control ECU and switch assembly (for Driver side)

·

Open or short in CAN No. 3 junction connector

·

Open or short in CAN No. 4 junction connector

·

Open or short in CAN No. 5 junction connector (for LHD)


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.

HINT:

This diagnosis procedure is for when DTC U1002 is output by the main body ECU (Intelligent tester display: Main Body).


WIRING DIAGRAM

C260144E03
0.365,0.74 1.573,0.927 1.208,0.188 10 false x: Suspected Area 4.771,0.583 6.458,0.99 1.688,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 3.313,0.344 3.729,0.531 0.417,0.188 10 false 120 Ω 2.625,0.938 3.063,1.104 0.438,0.167 10 false CANN 2.708,1.198 2.917,1.365 0.208,0.167 10 false 10 2.802,1.427 3.063,1.594 0.26,0.167 10 false GR 3.99,1.427 4.198,1.594 0.208,0.167 10 false R 4.146,1.198 4.354,1.365 0.208,0.167 10 false 9 4.49,0.583 4.854,0.75 0.365,0.167 10 false I12 3.979,0.938 4.406,1.104 0.427,0.167 10 false CANP 0.698,2.01 2.646,2.24 1.948,0.229 10 false CAN No. 3 Junction Connector 2.802,1.833 3.01,2 0.208,0.167 10 false 2 4.125,1.823 4.333,1.99 0.208,0.167 10 false 1 5.177,2.021 5.385,2.188 0.208,0.167 10 false G 5.135,2.802 5.406,2.969 0.271,0.167 10 false GR 3,1.823 3.302,1.99 0.302,0.167 10 false I116 3.75,1.823 4.042,1.99 0.292,0.167 10 false I116 4.365,2.792 4.573,2.958 0.208,0.167 10 false 2 4.375,2.031 4.583,2.198 0.208,0.167 10 false 1 4.292,2.219 4.594,2.385 0.302,0.167 10 false I171 4.292,2.583 4.594,2.75 0.302,0.167 10 false I171 3.01,3.729 3.302,3.896 0.292,0.167 10 false I117 3.76,3.729 4.052,3.896 0.292,0.167 10 false I117 4.135,3.729 4.344,3.896 0.208,0.167 10 false 1 2.802,3.74 3.01,3.906 0.208,0.167 10 false 2 5.698,2.104 5.906,2.271 0.208,0.167 10 false 9 5.698,2.708 5.979,2.875 0.281,0.167 10 false 8 5.865,2.073 6.302,2.24 0.438,0.167 10 false CANP 5.865,2.74 6.302,2.906 0.438,0.167 10 false CANN 2.198,2.823 2.406,2.99 0.208,0.167 10 false L 2.135,3.583 2.406,3.75 0.271,0.167 10 false GR 2.573,3.573 2.781,3.74 0.208,0.167 10 false 2 2.563,2.833 2.771,3 0.208,0.167 10 false 1 2.49,3.031 2.792,3.198 0.302,0.167 10 false I173 2.49,3.396 2.792,3.563 0.302,0.167 10 false I173 1.448,2.927 1.656,3.094 0.208,0.167 10 false 8 1.448,3.51 1.729,3.677 0.281,0.167 10 false 7 0.938,2.948 1.375,3.115 0.438,0.167 10 false CANP 0.938,3.49 1.375,3.656 0.438,0.167 10 false CANN 2.781,4.094 3.052,4.26 0.271,0.167 10 false GR 4.073,4.094 4.281,4.26 0.208,0.167 10 false Y 2.792,5.708 3.063,5.875 0.271,0.167 10 false GR 4.083,5.708 4.292,5.875 0.208,0.167 10 false V 4.135,4.458 4.344,4.625 0.208,0.167 10 false 1 2.813,4.458 2.99,4.625 0.177,0.167 10 false 2 3.01,4.458 3.302,4.625 0.292,0.167 10 false I120 3.76,4.458 4.052,4.625 0.292,0.167 10 false I120 4.135,5.49 4.344,5.656 0.208,0.167 10 false 1 2.813,5.49 2.99,5.656 0.177,0.167 10 false 2 4.135,6.031 4.344,6.198 0.208,0.167 10 false 3 2.813,6.031 2.99,6.198 0.177,0.167 10 false 2 3.01,5.5 3.302,5.667 0.292,0.167 10 false I121 3.76,5.5 4.052,5.667 0.292,0.167 10 false I121 4.292,4.729 6.271,4.927 1.979,0.198 10 false CAN No. 4 Junction Connector 4.844,6.25 6.135,6.573 1.292,0.323 10 false CAN No. 5 Junction Connector 3.333,6.594 3.75,6.781 0.417,0.188 10 false 120 Ω 3.875,8 5.583,8.188 1.708,0.188 10 false : CAN Branch Line (CANH) 3.875,8.417 5.583,8.604 1.708,0.188 10 false : CAN Branch Line (CANL) 0.896,8 2.813,8.188 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.896,8.417 2.813,8.604 1.917,0.188 10 false : CAN Main Bus Line (CANL) 2.552,5.323 2.76,5.49 0.208,0.167 10 false 2 2.563,4.583 2.771,4.75 0.208,0.167 10 false 1 2.479,4.781 2.781,4.948 0.302,0.167 10 false I172 2.479,5.146 2.781,5.313 0.302,0.167 10 false I172 1.875,4.594 2.083,4.76 0.208,0.167 10 false P 1.802,5.365 2.073,5.531 0.271,0.167 10 false GR 1.396,4.677 1.604,4.844 0.208,0.167 10 false 9 1.396,5.281 1.677,5.448 0.281,0.167 10 false 8 0.906,4.677 1.344,4.844 0.438,0.167 10 false CANP 0.917,5.281 1.354,5.448 0.438,0.167 10 false CANN 0.406,5.573 1.625,6.26 1.219,0.688 10 false Outer Mirror Control ECU Assembly (for Front Passenger Side) 0.115,5.573 0.375,5.74 0.26,0.167 10 false J13 5.813,2.99 7.115,3.542 1.302,0.552 10 false Outer Mirror Control ECU Assembly (for Driver Side) 5.5,2.99 5.792,3.156 0.292,0.167 10 false K12 4.521,6.25 4.833,6.417 0.313,0.167 10 false I123 0.396,3.823 2.542,4.521 2.146,0.698 10 false Position Control ECU and Switch Assembly (for Driver Side) 0.094,3.833 0.385,4 0.292,0.167 10 false e12 1.635,2.833 1.844,3 0.208,0.167 10 false L 1.615,3.583 1.823,3.75 0.208,0.167 10 false W 0.115,0.042 1.719,0.292 1.604,0.25 12 false Sub Bus 1 (for LHD): 2.656,6.24 3.094,6.406 0.438,0.167 10 false CANL 3.99,6.24 4.417,6.406 0.427,0.167 10 false CANH

C260145E02
0.365,1.781 1.573,1.969 1.208,0.188 10 false x: Suspected Area 4.802,1.021 6.49,1.427 1.688,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 3.344,0.719 3.76,0.906 0.417,0.188 10 false 120 Ω 2.646,1.385 3.083,1.552 0.438,0.167 10 false CANN 2.729,1.646 2.938,1.813 0.208,0.167 10 false 10 2.844,1.917 3.104,2.083 0.26,0.167 10 false GR 4.021,1.917 4.229,2.083 0.208,0.167 10 false R 4.167,1.646 4.375,1.813 0.208,0.167 10 false 9 4.531,1.021 4.896,1.188 0.365,0.167 10 false I12 4,1.385 4.427,1.552 0.427,0.167 10 false CANP 0.146,0.156 1.885,0.448 1.74,0.292 12 false Sub Bus 1 (for RHD): 1.385,2.833 2.625,3.427 1.24,0.594 10 false CAN No. 3 Junction Connector 2.823,2.292 3.031,2.458 0.208,0.167 10 false 2 4.125,2.281 4.333,2.448 0.208,0.167 10 false 1 5.115,2.708 5.323,2.875 0.208,0.167 10 false G 5.073,3.479 5.344,3.646 0.271,0.167 10 false GR 3.021,2.292 3.323,2.458 0.302,0.167 10 false I162 3.771,2.292 4.063,2.458 0.292,0.167 10 false I162 4.375,3.479 4.583,3.646 0.208,0.167 10 false 2 4.375,2.719 4.583,2.885 0.208,0.167 10 false 1 4.302,2.917 4.604,3.083 0.302,0.167 10 false I163 4.302,3.281 4.604,3.448 0.302,0.167 10 false I163 3.01,3.865 3.302,4.031 0.292,0.167 10 false I166 3.771,3.875 4.063,4.042 0.292,0.167 10 false I166 4.156,3.865 4.365,4.031 0.208,0.167 10 false 1 2.823,3.875 3.031,4.042 0.208,0.167 10 false 2 5.677,2.813 5.885,2.979 0.208,0.167 10 false 9 5.677,3.406 5.958,3.573 0.281,0.167 10 false 8 5.875,2.75 6.313,2.917 0.438,0.167 10 false CANP 5.875,3.448 6.313,3.615 0.438,0.167 10 false CANN 2.813,4.302 3.083,4.469 0.271,0.167 10 false GR 4.052,4.302 4.26,4.469 0.208,0.167 10 false Y 4.156,4.708 4.365,4.875 0.208,0.167 10 false 1 2.833,4.708 3.01,4.875 0.177,0.167 10 false 2 3.031,4.708 3.323,4.875 0.292,0.167 10 false I167 3.781,4.708 4.073,4.875 0.292,0.167 10 false I167 4.365,5.021 5.594,5.552 1.229,0.531 10 false CAN No. 4 Junction Connector 3.344,7.167 3.76,7.354 0.417,0.188 10 false 120 Ω 3.906,8.01 5.615,8.198 1.708,0.188 10 false : CAN Branch Line (CANH) 3.906,8.417 5.615,8.604 1.708,0.188 10 false : CAN Branch Line (CANL) 0.938,8.01 2.854,8.198 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.938,8.417 2.854,8.604 1.917,0.188 10 false : CAN Main Bus Line (CANL) 2.563,5.75 2.771,5.917 0.208,0.167 10 false 2 2.573,4.99 2.781,5.156 0.208,0.167 10 false 1 2.49,5.188 2.792,5.354 0.302,0.167 10 false I164 2.49,5.552 2.792,5.719 0.302,0.167 10 false I164 1.906,4.99 2.115,5.156 0.208,0.167 10 false P 1.844,5.76 2.115,5.927 0.271,0.167 10 false GR 1.438,5.073 1.646,5.24 0.208,0.167 10 false 9 1.438,5.667 1.719,5.833 0.281,0.167 10 false 8 0.917,5.042 1.354,5.208 0.438,0.167 10 false CANP 0.917,5.719 1.354,5.885 0.438,0.167 10 false CANN 4.385,6.594 4.594,6.76 0.208,0.167 10 false 2 4.385,5.833 4.594,6 0.208,0.167 10 false 1 4.302,6.021 4.604,6.188 0.302,0.167 10 false I165 4.302,6.375 4.604,6.542 0.302,0.167 10 false I165 5.667,3.646 6.896,4.354 1.229,0.708 10 false Outer Mirror Control ECU Assembly (for Front Passenger Side) 5.375,3.646 5.688,3.813 0.313,0.167 10 false K12 0.333,5.948 1.573,6.5 1.24,0.552 10 false Outer Mirror Control ECU Assembly (for Driver Side) 0.083,5.948 0.333,6.115 0.25,0.167 10 false J13 5.844,6.906 6.865,7.698 1.021,0.792 10 false Position Control ECU and Switch Assembly (for Driver Side) 5.844,6.75 6.135,6.917 0.292,0.167 10 false d12 4.75,6.573 5.021,6.74 0.271,0.167 10 false GR 5.708,5.906 5.917,6.073 0.208,0.167 10 false 8 5.708,6.51 5.99,6.677 0.281,0.167 10 false 7 5.865,5.844 6.302,6.01 0.438,0.167 10 false CANP 5.865,6.542 6.302,6.708 0.438,0.167 10 false CANN 4.75,5.823 5.021,5.99 0.271,0.167 10 false BE 5.469,6.573 5.688,6.74 0.219,0.167 10 false W 5.5,5.823 5.635,5.99 0.135,0.167 10 false L

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 10 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.

Result:
Result Proceed to
for RHD A
for LHD B




A

2.CHECK SUB BUS 1

B

20.CHECK SUB BUS 1
2.CHECK SUB BUS 1
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C236433C11
1.208,0.583 1.656,0.885 0.448,0.302 0.146,3.729 0.604,4.021 0.458,0.292 1.635,3.552 1.698,3.063 1.698,3.063 1.896,3.063 false 2.365,4.094 2.563,4.344 2.563,4.344 2.74,4.344 false 1.385,1.594 1.927,1.01 1.927,1.01 2.104,1.01 true 2.698,2.25 2.552,2.25 2.552,2.25 1.406,1.802 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.292,0.656 1.677,0.906 0.385,0.25 10 false I162 0.208,2.854 0.521,3.052 0.313,0.198 10 false *1 0.292,3.781 0.75,3.979 0.458,0.198 10 false I39 1.927,2.979 2.24,3.177 0.313,0.198 10 false CG 2.802,4.271 3.26,4.469 0.458,0.198 10 false BAT 2.177,0.927 2.792,1.125 0.615,0.198 10 false CANH 2.719,2.188 3.333,2.385 0.615,0.198 10 false CANL
*1 DLC3
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I162-1 (CANH) -I162-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in a main bus line
I162-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I162-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I162-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I162-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus line B
Short circuit between bus lines C
·

Ground short

·

+B short


D



A

3.RECONFIRM DTC OUTPUT

B

4.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

8.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

D

14.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
3.RECONFIRM DTC OUTPUT
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Clear the DTCs.


f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON and recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
U1002 is output from main body ECU (multiplex network body ECU) (Intelligent tester display: Main Body) A
Other DTC is output B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

4.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the wire harness connector (I162) from the CAN No. 3 junction connector.


b.
C235315C06
1.104,0.521 1.656,0.865 0.552,0.344 2.698,2.052 2.521,2.052 2.521,2.052 1.781,1.646 true 1.75,1.406 2.281,0.76 2.281,0.76 2.49,0.76 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.25,0.594 1.865,0.792 0.615,0.198 10 false I162 2.563,0.667 3.219,0.927 0.656,0.26 10 false CANH*b 2.74,1.969 3.313,2.188 0.573,0.219 10 false CANL*b
*a Rear view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I162-1 (CANH) - I162-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

5.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 3 J/C)

NG

7.CHECK FOR OPEN IN SUB BUS 1 MAIN LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
5.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 3 J/C)
a.

Reconnect the wire harness connector (I162) to the CAN No. 3 junction connector.


b.

Disconnect the wire harness connector (I166) from the CAN No. 3 junction connector.


c.
C247989C05
0.823,0.552 1.26,0.813 0.438,0.26 1.979,0.771 1.75,0.771 1.75,0.771 1.469,1.344 true 2.74,2.021 2.563,2.021 2.563,2.021 1.5,1.552 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.906,0.604 1.521,0.802 0.615,0.198 10 false I166 2.052,0.677 2.969,0.875 0.917,0.198 10 false CANH*b 2.802,1.948 3.354,2.177 0.552,0.229 10 false CANL*b
*a Rear view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to CAN No. 4 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I166-1 (CANH) - I166-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 3 JUNCTION CONNECTOR

NG

6.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 3 J/C - CAN NO. 4 J/C)
6.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 3 J/C - CAN NO. 4 J/C)
a.

Reconnect the wire harness connector (I166) to the CAN No. 3 junction connector.


b.

Disconnect the wire harness connector (I167) from the CAN No. 4 junction connector.


c.
C247989C06
0.823,0.552 1.26,0.813 0.438,0.26 1.979,0.76 1.75,0.76 1.75,0.76 1.469,1.333 true 2.729,2.021 2.552,2.021 2.552,2.021 1.49,1.552 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.906,0.604 1.521,0.802 0.615,0.198 10 false I167 2.052,0.677 2.969,0.875 0.917,0.198 10 false CANH*b 2.781,1.948 3.333,2.177 0.552,0.229 10 false CANL*b
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to CAN No. 3 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I167-1 (CANH) - I167-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 4 J/C)

7.CHECK FOR OPEN IN SUB BUS 1 MAIN LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Reconnect the wire harness connector (I162) to the CAN No. 3 junction connector.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.


c.
C204821C01
0.844,0.708 1.219,0.958 0.375,0.25 1.396,1.823 1.74,0.365 1.74,0.365 1.958,0.365 false 1.573,1.823 1.948,0.708 1.948,0.708 2.156,0.708 false 0.052,0.063 0.365,0.26 0.313,0.198 10 *a 0.927,0.75 1.385,0.948 0.458,0.198 10 I12 2,0.292 2.615,0.49 0.615,0.198 10 CANP 2.188,0.635 2.802,0.833 0.615,0.198 10 CANN
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-9 (CANP) - I12-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

8.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the wire harness connector (I162) from the CAN No. 3 junction connector.


b.
C235315C06
1.104,0.521 1.656,0.865 0.552,0.344 2.698,2.052 2.521,2.052 2.521,2.052 1.781,1.646 true 1.75,1.406 2.281,0.76 2.281,0.76 2.49,0.76 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.25,0.594 1.865,0.792 0.615,0.198 10 false I162 2.563,0.667 3.219,0.927 0.656,0.26 10 false CANH*b 2.74,1.969 3.313,2.188 0.573,0.219 10 false CANL*b
*a Rear view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I162-1 (CANH) - I162-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

9.CHECK FOR SHORT IN SUB BUS 1 LINES (BRANCH LINE)

NG

13.CHECK FOR SHORT IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
9.CHECK FOR SHORT IN SUB BUS 1 LINES (BRANCH LINE)
a.

Reconnect the wire harness connector (I162) to the CAN No. 3 junction connector.


b.
C247996C09
1.24,0.375 1.646,0.635 0.406,0.26 1.396,1.323 1.969,0.74 1.969,0.74 2.198,0.74 true 2.667,1.938 2.49,1.938 2.49,1.938 1.406,1.542 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 1.313,0.427 1.927,0.625 0.615,0.198 10 false I162 2.26,0.667 2.875,0.865 0.615,0.198 10 false CANH 2.708,1.865 3.323,2.063 0.615,0.198 10 false CANL
*a Component with harness connected
(CAN No. 3 Junction Connector)


Connect the probes of an ohmmeter to terminals 1 (CANH) and 2 (CANL) of the main body ECU main line harness connector.


c.

While observing the resistance value shown on the tester, disconnect connectors (I163, I164 and I165) from the CAN No. 3 junction connector or CAN No. 4 junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).

C248828C03
3.49,0.365 3.802,0.563 0.313,0.198 10 false *3 3.083,1.042 3.292,1.281 0.208,0.24 10 false R 3.615,1.042 3.927,1.24 0.313,0.198 10 false GR 4.896,1.031 5.052,1.229 0.156,0.198 10 false G 5.427,1.031 5.74,1.229 0.313,0.198 10 false GR 6.292,1.344 6.448,1.542 0.156,0.198 10 false Y 6.854,1.344 7.146,1.552 0.292,0.208 10 false GR 0.052,2.792 0.208,2.99 0.156,0.198 10 false Y 0.531,2.792 0.781,3.031 0.25,0.24 10 false GR 1.365,2.823 1.677,3.021 0.313,0.198 10 false *4 1.156,3.344 1.313,3.542 0.156,0.198 10 false P 1.635,3.344 1.948,3.542 0.313,0.198 10 false GR 3.167,2.802 3.479,3 0.313,0.198 10 false *5 2.948,3.198 3.104,3.396 0.156,0.198 10 false L 2.896,3.542 3.208,3.74 0.313,0.198 10 false BE 3.458,3.208 3.677,3.448 0.219,0.24 10 false W 3.448,3.552 3.76,3.75 0.313,0.198 10 false GR 3.521,4.01 3.833,4.208 0.313,0.198 10 false *6 3.365,1.563 3.677,1.76 0.313,0.198 10 false *1 5.167,1.552 5.479,1.75 0.313,0.198 10 false *2
*1 Main Body ECU (Multiplex Network Body ECU) *2 Outer Mirror Control ECU Assembly (for Front Passenger Side)
*3 CAN No. 3 Junction Connector *4 Outer Mirror Control ECU Assembly (for Driver Side)
*5 Position Control ECU and Switch Assembly (for Driver Side) *6 CAN No. 4 Junction Connector


C247999C08
6.198,1.74 6.469,2.542 false 1.135,4.688 1.573,4.531 false 1.583,5.031 1.146,4.875 false 0.083,0.094 0.531,0.417 0.448,0.323 10 false *1 1.354,0.656 1.802,0.979 0.448,0.323 10 false *a 4.427,0.656 4.865,0.979 0.438,0.323 10 false *b 6.406,2.563 6.854,2.885 0.448,0.323 10 false *c 0.563,4.094 1.01,4.417 0.448,0.323 10 false *d 1.615,4.458 2.146,4.688 0.531,0.229 10 false CANH 1.615,4.969 2.146,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I162 4.615,4.469 5.073,4.677 0.458,0.208 10 false I163 4.615,5.188 5.073,5.396 0.458,0.208 10 false I166
*1 CAN No. 3 Junction Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN No. 3 Junction Connector)


Wiring Color:
CAN No. 3 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
Main body ECU (Multiplex network body ECU) I162 R GR
Outer mirror control ECU assembly (for Front passenger side) I163 G GR
CAN main bus line (bus line connecting CAN No. 3 junction connector and CAN No. 4 junction connector) I166 Y GR


C248000C07
6.198,1.74 6.469,2.542 false 1.135,4.698 1.573,4.552 false 1.583,5.031 1.146,4.875 false 0.083,0.094 0.531,0.417 0.448,0.323 10 false *1 1.354,0.635 1.802,0.958 0.448,0.323 10 false *a 4.427,0.635 4.875,0.958 0.448,0.323 10 false *b 6.406,2.542 6.854,2.865 0.448,0.323 10 false *c 0.563,4.094 1.01,4.417 0.448,0.323 10 false *d 1.594,4.469 2.125,4.698 0.531,0.229 10 false CANH 1.594,4.969 2.125,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I164 4.615,4.479 5.073,4.688 0.458,0.208 10 false I165 4.615,3.75 5.073,3.958 0.458,0.208 10 false I168 4.615,5.198 5.073,5.406 0.458,0.208 10 false I167
*1 CAN No. 4 Junction Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN No. 4 Junction Connector)


Wiring Color:
CAN No. 4 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN No. 3 junction connector and CAN No. 4 junction connector) I167 Y GR
Position control ECU and switch assembly (for Driver side) I165 BE GR
Outer mirror control ECU assembly (for Driver side) I164 P GR


NOTICE:

Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.



Result:
Symptom Proceed to
The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of branch lines.) A
The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.) B


d.

When there is a short in one or more of the branch lines:

i.

Reconnect all of the connectors to the CAN J/C, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.

HINT:
·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

·

Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.






A

10.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 3 J/C)

B

12.CHECK FOR SHORT IN SUB BUS 1 LINES (ECU, SENSOR)
10.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 3 J/C)
a.

Disconnect the wire harness connector (I166) from the CAN No. 3 junction connector.


b.
C247996C09
1.24,0.375 1.646,0.635 0.406,0.26 1.396,1.323 1.969,0.74 1.969,0.74 2.198,0.74 true 2.667,1.938 2.49,1.938 2.49,1.938 1.406,1.542 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 1.313,0.427 1.927,0.625 0.615,0.198 10 false I162 2.26,0.667 2.875,0.865 0.615,0.198 10 false CANH 2.708,1.865 3.323,2.063 0.615,0.198 10 false CANL
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I162-1 (CANH) - I162-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 3 JUNCTION CONNECTOR

NG

11.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 3 J/C - CAN NO. 4 J/C)
11.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 3 J/C - CAN NO. 4 J/C)
a.

Reconnect the wire harness connector (I166) to the CAN No. 3 junction connector.


b.

Disconnect the wire harness connector (I167) from the CAN No. 4 junction connector.


c.
C247996C09
1.24,0.375 1.646,0.635 0.406,0.26 1.396,1.323 1.969,0.74 1.969,0.74 2.198,0.74 true 2.667,1.938 2.49,1.938 2.49,1.938 1.406,1.542 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 1.313,0.427 1.927,0.625 0.615,0.198 10 false I162 2.26,0.667 2.875,0.865 0.615,0.198 10 false CANH 2.708,1.865 3.323,2.063 0.615,0.198 10 false CANL
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I162-1 (CANH) - I162-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 4 J/C)

12.CHECK FOR SHORT IN SUB BUS 1 LINES (ECU, SENSOR)
a.

Reconnect the connector for the short-circuited branch line to the CAN junction connector (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU to which the short-circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C247996C09
1.24,0.375 1.646,0.635 0.406,0.26 1.396,1.323 1.969,0.74 1.969,0.74 2.198,0.74 true 2.667,1.938 2.49,1.938 2.49,1.938 1.406,1.542 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 1.313,0.427 1.927,0.625 0.615,0.198 10 false I162 2.26,0.667 2.875,0.865 0.615,0.198 10 false CANH 2.708,1.865 3.323,2.063 0.615,0.198 10 false CANL
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I162-1 (CANH) - I162-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU, there may be a short in the ECU.



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR

13.CHECK FOR SHORT IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Reconnect the wire harness connector (I162) to the CAN No. 3 junction connector.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.


c.
C204821C01
0.844,0.708 1.219,0.958 0.375,0.25 1.396,1.823 1.74,0.365 1.74,0.365 1.958,0.365 false 1.573,1.823 1.948,0.708 1.948,0.708 2.156,0.708 false 0.052,0.063 0.365,0.26 0.313,0.198 10 *a 0.927,0.75 1.385,0.948 0.458,0.198 10 I12 2,0.292 2.615,0.49 0.615,0.198 10 CANP 2.188,0.635 2.802,0.833 0.615,0.198 10 CANN
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-9 (CANP) - I12-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

14.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the wire harness connectors (I162) from the CAN No. 3 junction connector.


b.
C236584C05
1.5,0.583 1.917,0.896 0.417,0.313 0.135,3.719 0.531,3.99 0.396,0.271 1.635,3.542 1.958,3.083 1.958,3.083 2.104,3.083 false 2.344,4.104 2.594,4.385 2.594,4.385 2.781,4.385 false 1.063,0.76 1.24,0.76 1.24,0.76 1.667,1.354 true 1.26,2.563 1.427,2.563 1.427,2.563 1.698,1.563 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.573,0.656 1.938,0.896 0.365,0.24 10 false I162 0.208,2.979 0.521,3.177 0.313,0.198 10 false *1 0.24,3.76 0.698,3.958 0.458,0.198 10 false I39 2.177,3.021 2.49,3.219 0.313,0.198 10 false CG 2.833,4.313 3.292,4.51 0.458,0.198 10 false BAT 0.531,0.667 1.156,0.906 0.625,0.24 10 false CANH*b 0.719,2.49 1.635,2.688 0.917,0.198 10 false CANL*b
*1 DLC3
*a Rear view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I162-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I162-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I162-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I162-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

15.CHECK FOR SHORT IN SUB BUS 1 LINE (BRANCH LINE)

NG

19.CHECK FOR SHORT IN SUB BUS 1 LINE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
15.CHECK FOR SHORT IN SUB BUS 1 LINE (BRANCH LINE)
a.

Reconnect the wire harness connector (I162) to the CAN No. 3 junction connector.


b.
C236433C12
1.208,0.583 1.656,0.885 0.448,0.302 0.146,3.729 0.604,4.021 0.458,0.292 1.635,3.552 1.698,3.063 1.698,3.063 1.896,3.063 false 2.365,4.094 2.563,4.344 2.563,4.344 2.74,4.344 false 1.396,1.604 1.938,1.021 1.938,1.021 2.115,1.021 true 2.677,2.229 2.531,2.229 2.531,2.229 1.385,1.781 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.292,0.656 1.677,0.906 0.385,0.25 10 false I162 0.208,2.854 0.521,3.052 0.313,0.198 10 false *1 0.292,3.781 0.75,3.979 0.458,0.198 10 false I39 1.927,2.979 2.24,3.177 0.313,0.198 10 false CG 2.802,4.271 3.26,4.469 0.458,0.198 10 false BAT 2.177,0.927 2.792,1.125 0.615,0.198 10 false CANH 2.75,2.146 3.365,2.344 0.615,0.198 10 false CANL
*1 DLC3
*a Component with harness connected
(CAN No. 3 Junction Connector)


Connect the probes of an ohmmeter to terminals 1 (CANH) and 2 (CANL) of the wire harness connectors (I162) and CG or BAT of the DLC3.

HINT:

It is only necessary to perform the inspection for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.



c.

While observing the resistance value shown on the ohmmeter, disconnect branch line connector (I163, I164 and I165) from the CAN No. 3 junction connector or CAN No. 4 junction connector until the resistance becomes normal (6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short)).

C248828C03
3.49,0.365 3.802,0.563 0.313,0.198 10 false *3 3.083,1.042 3.292,1.281 0.208,0.24 10 false R 3.615,1.042 3.927,1.24 0.313,0.198 10 false GR 4.896,1.031 5.052,1.229 0.156,0.198 10 false G 5.427,1.031 5.74,1.229 0.313,0.198 10 false GR 6.292,1.344 6.448,1.542 0.156,0.198 10 false Y 6.854,1.344 7.146,1.552 0.292,0.208 10 false GR 0.052,2.792 0.208,2.99 0.156,0.198 10 false Y 0.531,2.792 0.781,3.031 0.25,0.24 10 false GR 1.365,2.823 1.677,3.021 0.313,0.198 10 false *4 1.156,3.344 1.313,3.542 0.156,0.198 10 false P 1.635,3.344 1.948,3.542 0.313,0.198 10 false GR 3.167,2.802 3.479,3 0.313,0.198 10 false *5 2.948,3.198 3.104,3.396 0.156,0.198 10 false L 2.896,3.542 3.208,3.74 0.313,0.198 10 false BE 3.458,3.208 3.677,3.448 0.219,0.24 10 false W 3.448,3.552 3.76,3.75 0.313,0.198 10 false GR 3.521,4.01 3.833,4.208 0.313,0.198 10 false *6 3.365,1.563 3.677,1.76 0.313,0.198 10 false *1 5.167,1.552 5.479,1.75 0.313,0.198 10 false *2
*1 Main Body ECU (Multiplex Network Body ECU) *2 Outer Mirror Control ECU Assembly (for Front Passenger Side)
*3 CAN No. 3 Junction Connector *4 Outer Mirror Control ECU Assembly (for Driver Side)
*5 Position Control ECU and Switch Assembly (for Driver Side) *6 CAN No. 4 Junction Connector


C247999C08
6.198,1.74 6.469,2.542 false 1.135,4.688 1.573,4.531 false 1.583,5.031 1.146,4.875 false 0.083,0.094 0.531,0.417 0.448,0.323 10 false *1 1.354,0.656 1.802,0.979 0.448,0.323 10 false *a 4.427,0.656 4.865,0.979 0.438,0.323 10 false *b 6.406,2.563 6.854,2.885 0.448,0.323 10 false *c 0.563,4.094 1.01,4.417 0.448,0.323 10 false *d 1.615,4.458 2.146,4.688 0.531,0.229 10 false CANH 1.615,4.969 2.146,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I162 4.615,4.469 5.073,4.677 0.458,0.208 10 false I163 4.615,5.188 5.073,5.396 0.458,0.208 10 false I166
*1 CAN No. 3 Junction Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN No. 3 Junction Connector)


Wiring Color:
CAN No. 3 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
Main body ECU (Multiplex network body ECU) I162 R GR
Outer mirror control ECU assembly (for Front passenger side) I163 G GR
CAN main bus line (bus line connecting CAN No. 3 junction connector and CAN No. 4 junction connector) I166 Y GR


C248000C07
6.198,1.74 6.469,2.542 false 1.135,4.698 1.573,4.552 false 1.583,5.031 1.146,4.875 false 0.083,0.094 0.531,0.417 0.448,0.323 10 false *1 1.354,0.635 1.802,0.958 0.448,0.323 10 false *a 4.427,0.635 4.875,0.958 0.448,0.323 10 false *b 6.406,2.542 6.854,2.865 0.448,0.323 10 false *c 0.563,4.094 1.01,4.417 0.448,0.323 10 false *d 1.594,4.469 2.125,4.698 0.531,0.229 10 false CANH 1.594,4.969 2.125,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I164 4.615,4.479 5.073,4.688 0.458,0.208 10 false I165 4.615,3.75 5.073,3.958 0.458,0.208 10 false I168 4.615,5.198 5.073,5.406 0.458,0.208 10 false I167
*1 CAN No. 4 Junction Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN No. 4 Junction Connector)


Wiring Color:
CAN No. 4 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN No. 3 junction connector and CAN No. 4 junction connector) I167 Y GR
Position control ECU and switch assembly (for Driver side) I165 BE GR
Outer mirror control ECU assembly (for Driver side) I164 P GR



Result:
Result Proceed to
The resistance between terminals CANP and BAT, or the resistance between terminals CANN and BAT is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector.
(There is no short to +B in the branch lines.)
A
The resistance between terminals CANP and GND, or the resistance between terminals CANN and GND is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector.
(There is no short to GND in the branch lines.)
The resistance between terminals CANP and BAT, or the resistance between terminals CANN and BAT becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to +B in one of the areas related to one or more of the disconnected branch lines.)
B
The resistance between terminals CANP and GND, or the resistance between terminals CANN and GND becomes normal (200 Ω or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to GND in one of the areas related to one or more of the disconnected branch lines.)



A

16.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 3 J/C)

B

18.CHECK FOR SHORT IN SUB BUS 1 LINE (ECU, SENSOR)
16.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 3 J/C)
a.

Disconnect the wire harness connectors (I166) from the CAN No. 3 junction connector.


b.
C236433C12
1.208,0.583 1.656,0.885 0.448,0.302 0.146,3.729 0.604,4.021 0.458,0.292 1.635,3.552 1.698,3.063 1.698,3.063 1.896,3.063 false 2.365,4.094 2.563,4.344 2.563,4.344 2.74,4.344 false 1.396,1.604 1.938,1.021 1.938,1.021 2.115,1.021 true 2.677,2.229 2.531,2.229 2.531,2.229 1.385,1.781 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.292,0.656 1.677,0.906 0.385,0.25 10 false I162 0.208,2.854 0.521,3.052 0.313,0.198 10 false *1 0.292,3.781 0.75,3.979 0.458,0.198 10 false I39 1.927,2.979 2.24,3.177 0.313,0.198 10 false CG 2.802,4.271 3.26,4.469 0.458,0.198 10 false BAT 2.177,0.927 2.792,1.125 0.615,0.198 10 false CANH 2.75,2.146 3.365,2.344 0.615,0.198 10 false CANL
*1 DLC3
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I162-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I162-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I162-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I162-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 3 JUNCTION CONNECTOR

NG

17.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 3 J/C - CAN NO. 4 J/C)
17.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 3 J/C - CAN NO. 4 J/C)
a.

Reconnect the wire harness connector (I166) to the CAN No. 3 junction connector.


b.

Disconnect the wire harness connector (I167) from the CAN No. 4 junction connector.


c.
C236433C12
1.208,0.583 1.656,0.885 0.448,0.302 0.146,3.729 0.604,4.021 0.458,0.292 1.635,3.552 1.698,3.063 1.698,3.063 1.896,3.063 false 2.365,4.094 2.563,4.344 2.563,4.344 2.74,4.344 false 1.396,1.604 1.938,1.021 1.938,1.021 2.115,1.021 true 2.677,2.229 2.531,2.229 2.531,2.229 1.385,1.781 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.292,0.656 1.677,0.906 0.385,0.25 10 false I162 0.208,2.854 0.521,3.052 0.313,0.198 10 false *1 0.292,3.781 0.75,3.979 0.458,0.198 10 false I39 1.927,2.979 2.24,3.177 0.313,0.198 10 false CG 2.802,4.271 3.26,4.469 0.458,0.198 10 false BAT 2.177,0.927 2.792,1.125 0.615,0.198 10 false CANH 2.75,2.146 3.365,2.344 0.615,0.198 10 false CANL
*1 DLC3
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I162-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I162-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I162-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I162-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 4 J/C)

18.CHECK FOR SHORT IN SUB BUS 1 LINE (ECU, SENSOR)
a.

Reconnect the connector for the bus line that is shorted to +B or GND to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short) when it was disconnected).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU to which the bus line shorted to +B or GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C236433C12
1.208,0.583 1.656,0.885 0.448,0.302 0.146,3.729 0.604,4.021 0.458,0.292 1.635,3.552 1.698,3.063 1.698,3.063 1.896,3.063 false 2.365,4.094 2.563,4.344 2.563,4.344 2.74,4.344 false 1.396,1.604 1.938,1.021 1.938,1.021 2.115,1.021 true 2.677,2.229 2.531,2.229 2.531,2.229 1.385,1.781 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.292,0.656 1.677,0.906 0.385,0.25 10 false I162 0.208,2.854 0.521,3.052 0.313,0.198 10 false *1 0.292,3.781 0.75,3.979 0.458,0.198 10 false I39 1.927,2.979 2.24,3.177 0.313,0.198 10 false CG 2.802,4.271 3.26,4.469 0.458,0.198 10 false BAT 2.177,0.927 2.792,1.125 0.615,0.198 10 false CANH 2.75,2.146 3.365,2.344 0.615,0.198 10 false CANL
*1 DLC3
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I162-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I162-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I162-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I162-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

If the resistance becomes normal when the connector is disconnected from the ECU, there may be a short in the ECU.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR

19.CHECK FOR SHORT IN SUB BUS 1 LINE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.
C236584C05
1.5,0.583 1.917,0.896 0.417,0.313 0.135,3.719 0.531,3.99 0.396,0.271 1.635,3.542 1.958,3.083 1.958,3.083 2.104,3.083 false 2.344,4.104 2.594,4.385 2.594,4.385 2.781,4.385 false 1.063,0.76 1.24,0.76 1.24,0.76 1.667,1.354 true 1.26,2.563 1.427,2.563 1.427,2.563 1.698,1.563 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.573,0.656 1.938,0.896 0.365,0.24 10 false I162 0.208,2.979 0.521,3.177 0.313,0.198 10 false *1 0.24,3.76 0.698,3.958 0.458,0.198 10 false I39 2.177,3.021 2.49,3.219 0.313,0.198 10 false CG 2.833,4.313 3.292,4.51 0.458,0.198 10 false BAT 0.531,0.667 1.156,0.906 0.625,0.24 10 false CANH*b 0.719,2.49 1.635,2.688 0.917,0.198 10 false CANL*b
*1 DLC3
*a Rear view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I162-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I162-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I162-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I162-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

20.CHECK SUB BUS 1
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C253924C02
2.354,0.167 2.771,0.385 0.417,0.219 0.156,3.281 0.573,3.5 0.417,0.219 2.594,0.969 2.896,0.5 false 2.604,1.188 2.854,1.625 false 1.646,3.104 1.802,2.552 1.802,2.552 1.969,2.552 false 2.354,3.656 2.552,4.135 2.552,4.135 2.719,4.135 false 0.115,2.552 0.427,2.708 0.313,0.156 10 false *1 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 2.427,0.188 3.042,0.385 0.615,0.198 10 false I116 2.906,0.333 3.417,0.552 0.51,0.219 10 false CANH 2.917,1.604 3.427,1.823 0.51,0.219 10 false CANL 2.021,2.469 2.531,2.688 0.51,0.219 10 false CG 2.76,4.052 3.271,4.271 0.51,0.219 10 false BAT 0.271,3.313 0.885,3.51 0.615,0.198 10 false I39
*1 DLC3
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I116-1 (CANH) - I116-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in a main bus line
I116-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I116-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I116-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I116-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus line B
Short circuit between bus lines C
·

Ground short

·

+B short


D



A

21.RECONFIRM DTC OUTPUT

B

22.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

28.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

D

36.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
21.RECONFIRM DTC OUTPUT
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Clear the DTCs.


f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON and recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
U1002 is output from main body ECU (multiplex network body ECU) (Intelligent tester display: Main Body) A
Other DTC is output B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

22.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the wire harness connector (I116) from the CAN No. 3 junction connector.


b.
C253925C02
2.375,1.708 2.781,1.927 0.406,0.219 2.875,2.844 2.625,2.573 false 2.885,2.052 2.625,2.365 false 0.073,0.115 0.385,0.271 0.313,0.156 10 false *a 2.865,1.906 3.427,2.104 0.563,0.198 10 false CANH*b 2.865,2.833 3.427,3.031 0.563,0.198 10 false CANL*b 2.448,1.729 2.875,1.958 0.427,0.229 10 false I116
*a Rear view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I116-1 (CANH) - I116-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



Result:
Result
OK
NG



OK

23.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 3 J/C)

NG

27.CHECK FOR OPEN IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
23.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 3 J/C)
a.

Reconnect the wire harness connector (I116) to the CAN No. 3 junction connector.


b.

Disconnect the wire harness connector (I117) from the CAN No. 3 junction connector.


c.
C258007C01
1.323,1.771 1.729,2.01 0.406,0.24 1.563,2.365 1.958,2.115 false 1.563,2.563 1.948,2.771 false 0,0 0.313,0.156 0.313,0.156 10 false *a 2.01,2.01 2.656,2.198 0.646,0.188 10 false CANH*b 2.01,2.708 2.656,2.896 0.646,0.188 10 false CANL*b 1.406,1.813 1.75,2.01 0.344,0.198 10 false I117
*a Rear view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to CAN No. 4 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I117-1 (CANH) - I117-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 3 JUNCTION CONNECTOR

NG

24.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 3 J/C - CAN NO. 4 J/C)
24.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 3 J/C - CAN NO. 4 J/C)
a.

Reconnect the wire harness connector (I117) to the CAN No. 3 junction connector.


b.

Disconnect the wire harness connector (I120) from the CAN No. 4 junction connector.


c.
C250116C05
1.344,1.604 1.74,1.833 0.396,0.229 2.281,2.708 1.615,2.417 false 2.26,1.854 1.615,2.26 false 0.094,0.094 0.323,0.323 0.229,0.229 10 false *a 1.417,1.635 1.771,1.813 0.354,0.177 10 false I120 2.281,1.771 2.875,2.01 0.594,0.24 10 false CANH*b 2.313,2.646 2.948,2.885 0.635,0.24 10 false CANL*b
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to CAN No. 3 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I120-1 (CANH) - I120-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

25.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 4 J/C)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 4 J/C)

25.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 4 J/C)
a.

Reconnect the wire harness connector (I120) to the CAN No. 4 junction connector.


b.

Disconnect the wire harness connector (I121) from the CAN No. 4 junction connector.


c.
C250201C03
1.021,1.74 1.406,1.99 0.385,0.25 1.948,2.844 1.281,2.552 false 1.927,2 1.281,2.406 false 0.063,0.063 0.313,0.271 0.25,0.208 10 false *a 1.083,1.781 1.438,1.958 0.354,0.177 10 false I121 1.969,1.885 2.563,2.125 0.594,0.24 10 false CANH*b 2,2.802 2.635,3.042 0.635,0.24 10 false CANL*b
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to CAN No. 5 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I121-1 (CANH) - I121-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

26.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 4 J/C - CAN NO. 5 J/C)
26.CHECK FOR OPEN IN SUB BUS 1 LINES (CAN NO. 4 J/C - CAN NO. 5 J/C)
a.

Reconnect the wire harness connector (I121) to the CAN No. 4 junction connector.


b.

Disconnect the CAN No. 5 junction connector.


c.
C183982C15
1.875,2.083 2.302,2.323 0.427,0.24 1.75,0.854 1.458,0.854 1.458,0.854 0.656,2.167 false 1.75,1.271 1.51,1.271 1.51,1.271 0.969,2.167 false 0.115,0.063 0.344,0.302 0.229,0.24 10 false *a 1.833,0.781 2.51,1.042 0.677,0.26 10 false CANH*b 1.813,1.198 2.49,1.458 0.677,0.26 10 false CANL*b 1.958,2.125 2.375,2.333 0.417,0.208 10 false I123
*a Rear view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 4 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I123-3 (CANH) - I123-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 5 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 4 J/C - CAN NO. 5 J/C)

27.CHECK FOR OPEN IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Reconnect the wire harness connector (I116) to the CAN No. 3 junction connector.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.


c.
C204821C01
0.844,0.708 1.219,0.958 0.375,0.25 1.396,1.823 1.74,0.365 1.74,0.365 1.958,0.365 false 1.573,1.823 1.948,0.708 1.948,0.708 2.156,0.708 false 0.052,0.063 0.365,0.26 0.313,0.198 10 *a 0.927,0.75 1.385,0.948 0.458,0.198 10 I12 2,0.292 2.615,0.49 0.615,0.198 10 CANP 2.188,0.635 2.802,0.833 0.615,0.198 10 CANN
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-9 (CANP) - I12-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

28.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the wire harness connector (I116) from the CAN No. 3 junction connector.


b.
C253925C03
2.375,1.708 2.781,1.927 0.406,0.219 2.875,2.844 2.625,2.573 false 2.885,2.052 2.625,2.365 false 0.073,0.115 0.385,0.271 0.313,0.156 10 false *a 2.865,1.906 3.427,2.104 0.563,0.198 10 false CANH*b 2.865,2.833 3.427,3.031 0.563,0.198 10 false CANL*b 2.448,1.729 2.875,1.958 0.427,0.229 10 false I116
*a Rear view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I116-1 (CANH) - I116-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

29.CHECK FOR SHORT IN SUB BUS 1 LINES (BRANCH LINE)

NG

35.CHECK FOR SHORT IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
29.CHECK FOR SHORT IN SUB BUS 1 LINES (BRANCH LINE)
a.

Reconnect the wire harness connector (I116) to the CAN No. 3 junction connector.


b.
C253927C02
2.344,0.708 2.76,0.927 0.417,0.219 2.604,1.438 2.875,1.021 false 2.604,1.635 2.833,2.052 false 0.115,0.135 0.427,0.292 0.313,0.156 10 false *a 2.427,0.729 2.74,0.927 0.313,0.198 10 false I116 2.917,0.865 3.385,1.073 0.469,0.208 10 false CANH 2.896,2.031 3.385,2.26 0.49,0.229 10 false CANL
*a Component with harness connected
(CAN No. 3 Junction Connector)


Connect the probes of an ohmmeter to terminals 1 (CANH) and 2 (CANL) of the main body ECU main line harness connector.


c.

While observing the resistance value shown on the tester, disconnect connectors (I171, I173 and I172) from the CAN No. 3 junction connector or CAN No. 4 junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).

C260163C01
1.042,1.594 1.354,1.75 0.313,0.156 10 false *1 2.854,1.583 3.167,1.74 0.313,0.156 10 false *2 4.604,1.594 4.917,1.75 0.313,0.156 10 false *3 3.427,0.406 3.74,0.563 0.313,0.156 10 false *4 1.427,2.802 1.74,2.958 0.313,0.156 10 false *5 3.417,2.813 3.729,2.969 0.313,0.156 10 false *6 3.521,4.042 3.833,4.198 0.313,0.156 10 false *7 0.792,0.896 0.948,1.052 0.156,0.156 10 false L 0.792,1.219 0.948,1.375 0.156,0.156 10 false L 1.271,1.229 1.427,1.385 0.156,0.156 10 false W 1.271,0.885 1.573,1.031 0.302,0.146 10 false GR 3.125,1.042 3.427,1.188 0.302,0.146 10 false GR 2.646,1.042 2.865,1.188 0.219,0.146 10 false R 4.865,1.052 5.167,1.198 0.302,0.146 10 false GR 4.396,1.052 4.698,1.198 0.302,0.146 10 false G 6.833,1.406 7.135,1.552 0.302,0.146 10 false GR 6.344,1.417 6.615,1.563 0.271,0.146 10 false Y 0.094,3 0.396,3.146 0.302,0.146 10 false Y 0.542,3 0.844,3.146 0.302,0.146 10 false GR 1.24,3.396 1.542,3.542 0.302,0.146 10 false P 1.688,3.396 1.99,3.542 0.302,0.146 10 false GR 3.667,3.438 3.969,3.583 0.302,0.146 10 false GR 3.188,3.427 3.49,3.573 0.302,0.146 10 false V
*1 Position Control ECU and Switch Assembly (for Driver Side) *2 Main Body ECU (Multiplex Network Body ECU)
*3 Outer Mirror Control ECU Assembly (for Driver Side) *4 CAN No. 3 Junction Connector
*5 Outer Mirror Control ECU Assembly (for Front Passenger Side) *6 CAN No. 5 Junction Connector
*7 CAN No. 4 Junction Connector - -


C253934C03
2.354,0.438 2.667,0.594 0.313,0.156 10 false *a 3.573,2.583 3.917,2.76 0.344,0.177 10 false I116 3.573,2.844 3.917,3.021 0.344,0.177 10 false I171 3.573,3.125 3.917,3.302 0.344,0.177 10 false I173 3.573,3.417 3.917,3.594 0.344,0.177 10 false I117
*a Component without harness connected
(CAN No. 3 Junction Connector)
- -


Wiring Color:
CAN No. 3 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN No. 3 junction connector and Main body ECU (Multiplex network body ECU)) I116 R GR
CAN main bus line (bus line connecting CAN No. 3 junction connector and CAN No. 4 junction connector) I117 Y GR
Outer mirror control ECU assembly (for Driver side) I171 G GR
Position control ECU and switch assembly (for Driver side) I173 L GR


C250215C04
2.365,0.375 2.552,0.563 0.188,0.188 10 false *a 3.563,3.406 3.917,3.583 0.354,0.177 10 false I120 3.563,3.688 3.917,3.865 0.354,0.177 10 false I121 3.563,3.948 3.917,4.125 0.354,0.177 10 false I172
*a Component without harness connected
(CAN No. 4 Junction Connector)
- -


Wiring Color:
CAN No. 4 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
Outer mirror control ECU assembly (for Front passenger side) I172 P GR
CAN main bus line (bus line connecting CAN No. 3 junction connector and CAN No. 4 junction connector) I120 Y GR
CAN main bus line (bus line connecting CAN No. 4 junction connector and CAN No. 5 junction connector) I121 V GR


NOTICE:

Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.



Result:
Symptom Proceed to
The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of branch lines.) A
The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.) B


d.

When there is a short in one or more of the branch lines:

i.

Reconnect all of the connectors to the CAN J/C, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.

HINT:
·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

·

Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.






A

30.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 3 J/C)

B

34.CHECK FOR SHORT IN SUB BUS 1 LINES (ECU, SENSOR)
30.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 3 J/C)
a.

Disconnect the wire harness connector (I117) from the CAN No. 3 junction connector.


b.
C253926C02
2.396,0.167 2.74,0.396 0.344,0.229 2.594,0.792 2.875,0.344 false 2.604,1 2.833,1.375 false 0,0 0.313,0.156 0.313,0.156 10 false *a 2.438,0.188 2.833,0.365 0.396,0.177 10 false I116 2.885,0.188 3.365,0.385 0.479,0.198 10 false CANH 2.875,1.354 3.354,1.552 0.479,0.198 10 false CANL
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I116-1 (CANH) - I116-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

31.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 3 J/C - CAN NO. 4 J/C)

NG

REPLACE CAN NO. 3 JUNCTION CONNECTOR

31.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 3 J/C - CAN NO. 4 J/C)
a.

Reconnect the wire harness connector (I117) to the CAN No. 3 junction connector.


b.

Disconnect the wire harness connector (I120) from the CAN No. 4 junction connector.


c.
C253927C02
2.344,0.708 2.76,0.927 0.417,0.219 2.604,1.438 2.875,1.021 false 2.604,1.635 2.833,2.052 false 0.115,0.135 0.427,0.292 0.313,0.156 10 false *a 2.427,0.729 2.74,0.927 0.313,0.198 10 false I116 2.917,0.865 3.385,1.073 0.469,0.208 10 false CANH 2.896,2.031 3.385,2.26 0.49,0.229 10 false CANL
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I116-1 (CANH) - I116-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

32.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 4 J/C)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 4 J/C)

32.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 4 J/C)
a.

Reconnect the wire harness connector (I120) to the CAN No. 4 junction connector.


b.

Disconnect the wire harness connector (I121) from the CAN No. 4 junction connector.


c.
C253927C02
2.344,0.708 2.76,0.927 0.417,0.219 2.604,1.438 2.875,1.021 false 2.604,1.635 2.833,2.052 false 0.115,0.135 0.427,0.292 0.313,0.156 10 false *a 2.427,0.729 2.74,0.927 0.313,0.198 10 false I116 2.917,0.865 3.385,1.073 0.469,0.208 10 false CANH 2.896,2.031 3.385,2.26 0.49,0.229 10 false CANL
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I116-1 (CANH) - I116-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




Result:
Result
OK
NG



OK

33.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 4 J/C - CAN NO. 5 J/C)

NG

REPLACE CAN NO. 4 JUNCTION CONNECTOR

33.CHECK FOR SHORT IN SUB BUS 1 LINES (CAN NO. 4 J/C - CAN NO. 5 J/C)
a.

Reconnect the wire harness connector (I121) to the CAN No. 4 junction connector.


b.

Disconnect the CAN No. 5 junction connector.


c.
C253927C02
2.344,0.708 2.76,0.927 0.417,0.219 2.604,1.438 2.875,1.021 false 2.604,1.635 2.833,2.052 false 0.115,0.135 0.427,0.292 0.313,0.156 10 false *a 2.427,0.729 2.74,0.927 0.313,0.198 10 false I116 2.917,0.865 3.385,1.073 0.469,0.208 10 false CANH 2.896,2.031 3.385,2.26 0.49,0.229 10 false CANL
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I116-1 (CANH) - I116-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 5 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 4 J/C - CAN NO. 5 J/C)

34.CHECK FOR SHORT IN SUB BUS 1 LINES (ECU, SENSOR)
a.

Reconnect the connector for the short-circuited branch line to the CAN junction connector (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU to which the short-circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C253927C02
2.344,0.708 2.76,0.927 0.417,0.219 2.604,1.438 2.875,1.021 false 2.604,1.635 2.833,2.052 false 0.115,0.135 0.427,0.292 0.313,0.156 10 false *a 2.427,0.729 2.74,0.927 0.313,0.198 10 false I116 2.917,0.865 3.385,1.073 0.469,0.208 10 false CANH 2.896,2.031 3.385,2.26 0.49,0.229 10 false CANL
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I116-1 (CANH) - I116-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU, there may be a short in the ECU.



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR

35.CHECK FOR SHORT IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Reconnect the wire harness connector (I116) to the CAN No. 3 junction connector.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.


c.
C204821C02
0.844,0.708 1.219,0.958 0.375,0.25 1.396,1.823 1.74,0.365 1.74,0.365 1.958,0.365 false 1.573,1.823 1.948,0.708 1.948,0.708 2.156,0.708 false 0.052,0.063 0.365,0.26 0.313,0.198 10 *a 0.927,0.75 1.385,0.948 0.458,0.198 10 I12 2,0.292 2.615,0.49 0.615,0.198 10 CANP 2.188,0.635 2.802,0.833 0.615,0.198 10 CANN
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-9 (CANP) - I12-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

36.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the wire harness connector (I116) from the CAN No. 3 junction connector.


b.
C287982C02
2.323,1.573 2.708,1.781 0.385,0.208 0.219,3.833 0.51,4.042 0.292,0.208 2.792,1.99 2.563,2.146 false 2.792,2.479 2.573,2.333 false 1.781,3.208 1.677,3.208 1.677,3.208 1.594,3.594 false 2.583,4.5 2.438,4.5 2.438,4.5 2.313,4.156 false 0.281,3.26 0.594,3.417 0.313,0.156 10 false *1 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 2.844,1.885 3.427,2.063 0.583,0.177 10 false CANH*b 2.844,2.448 3.427,2.646 0.583,0.198 10 false CANL*b 2.385,1.594 2.75,1.781 0.365,0.188 10 false I116 0.271,3.854 0.542,4.042 0.271,0.188 10 false I39 1.833,3.115 2.198,3.302 0.365,0.188 10 false CG 2.646,4.406 3.073,4.594 0.427,0.188 10 false BAT
*1 DLC3
*a Rear view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I116-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I116-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I116-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I116-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

37.CHECK FOR SHORT IN SUB BUS 1 LINE (BRANCH LINE)

NG

43.CHECK FOR SHORT IN SUB BUS 1 LINE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
37.CHECK FOR SHORT IN SUB BUS 1 LINE (BRANCH LINE)
a.

Reconnect the wire harness connector (I116) to the CAN No. 3 junction connector.


b.
C253924C03
2.354,0.167 2.771,0.385 0.417,0.219 0.156,3.281 0.573,3.5 0.417,0.219 2.594,0.969 2.896,0.5 false 2.604,1.188 2.854,1.625 false 1.646,3.104 1.802,2.552 1.802,2.552 1.969,2.552 false 2.354,3.656 2.552,4.135 2.552,4.135 2.719,4.135 false 0.115,2.552 0.427,2.708 0.313,0.156 10 false *1 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 2.427,0.188 3.042,0.385 0.615,0.198 10 false I116 2.906,0.333 3.417,0.552 0.51,0.219 10 false CANH 2.917,1.604 3.427,1.823 0.51,0.219 10 false CANL 2.021,2.469 2.531,2.688 0.51,0.219 10 false CG 2.76,4.052 3.271,4.271 0.51,0.219 10 false BAT 0.271,3.313 0.885,3.51 0.615,0.198 10 false I39
*1 DLC3
*a Component with harness connected
(CAN No. 3 Junction Connector)


Connect the probes of an ohmmeter to terminals 1 (CANH) and 2 (CANL) of the wire harness connectors (I116) and CG or BAT of the DLC3.

HINT:

It is only necessary to perform the inspection for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.



c.

While observing the resistance value shown on the ohmmeter, disconnect branch line connectors (I171, I173 and I172) from the CAN No. 3 junction connector or CAN No. 4 junction connector until the resistance becomes normal (6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short)).

C260163C01
1.042,1.594 1.354,1.75 0.313,0.156 10 false *1 2.854,1.583 3.167,1.74 0.313,0.156 10 false *2 4.604,1.594 4.917,1.75 0.313,0.156 10 false *3 3.427,0.406 3.74,0.563 0.313,0.156 10 false *4 1.427,2.802 1.74,2.958 0.313,0.156 10 false *5 3.417,2.813 3.729,2.969 0.313,0.156 10 false *6 3.521,4.042 3.833,4.198 0.313,0.156 10 false *7 0.792,0.896 0.948,1.052 0.156,0.156 10 false L 0.792,1.219 0.948,1.375 0.156,0.156 10 false L 1.271,1.229 1.427,1.385 0.156,0.156 10 false W 1.271,0.885 1.573,1.031 0.302,0.146 10 false GR 3.125,1.042 3.427,1.188 0.302,0.146 10 false GR 2.646,1.042 2.865,1.188 0.219,0.146 10 false R 4.865,1.052 5.167,1.198 0.302,0.146 10 false GR 4.396,1.052 4.698,1.198 0.302,0.146 10 false G 6.833,1.406 7.135,1.552 0.302,0.146 10 false GR 6.344,1.417 6.615,1.563 0.271,0.146 10 false Y 0.094,3 0.396,3.146 0.302,0.146 10 false Y 0.542,3 0.844,3.146 0.302,0.146 10 false GR 1.24,3.396 1.542,3.542 0.302,0.146 10 false P 1.688,3.396 1.99,3.542 0.302,0.146 10 false GR 3.667,3.438 3.969,3.583 0.302,0.146 10 false GR 3.188,3.427 3.49,3.573 0.302,0.146 10 false V
*1 Position Control ECU and Switch Assembly (for Driver Side) *2 Main Body ECU (Multiplex Network Body ECU)
*3 Outer Mirror Control ECU Assembly (for Driver Side) *4 CAN No. 3 Junction Connector
*5 Outer Mirror Control ECU Assembly (for Front Passenger Side) *6 CAN No. 5 Junction Connector
*7 CAN No. 4 Junction Connector - -


C253934C03
2.354,0.438 2.667,0.594 0.313,0.156 10 false *a 3.573,2.583 3.917,2.76 0.344,0.177 10 false I116 3.573,2.844 3.917,3.021 0.344,0.177 10 false I171 3.573,3.125 3.917,3.302 0.344,0.177 10 false I173 3.573,3.417 3.917,3.594 0.344,0.177 10 false I117
*a Component without harness connected
(CAN No. 3 Junction Connector)
- -


Wiring Color:
CAN No. 3 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN No. 3 junction connector and Main body ECU (Multiplex network body ECU)) I116 R GR
CAN main bus line (bus line connecting CAN No. 3 junction connector and CAN No. 4 junction connector) I117 Y GR
Outer mirror control ECU assembly (for Driver side) I171 G GR
Position control ECU and switch assembly (for Driver side) I173 L GR


C250215C02
2.302,0.406 2.615,0.563 0.313,0.156 10 *a 3.583,3.417 4.198,3.615 0.615,0.198 10 I120 3.583,3.688 4.198,3.885 0.615,0.198 10 I121 3.583,3.958 4.198,4.156 0.615,0.198 10 I166
*a Component without harness connected
(CAN No. 4 Junction Connector)
- -


Wiring Color:
CAN No. 4 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
Outer mirror control ECU assembly (for Front passenger side) I172 P GR
CAN main bus line (bus line connecting CAN No. 3 junction connector and CAN No. 4 junction connector) I120 Y GR
CAN main bus line (bus line connecting CAN No. 4 junction connector and CAN No. 5 junction connector) I121 V GR



Result:
Result Proceed to
The resistance between terminals CANP and BAT, or the resistance between terminals CANN and BAT is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector.
(There is no short to +B in the branch lines.)
A
The resistance between terminals CANP and GND, or the resistance between terminals CANN and GND is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector.
(There is no short to GND in the branch lines.)
The resistance between terminals CANP and BAT, or the resistance between terminals CANN and BAT becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to +B in one of the areas related to one or more of the disconnected branch lines.)
B
The resistance between terminals CANP and GND, or the resistance between terminals CANN and GND becomes normal (200 Ω or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to GND in one of the areas related to one or more of the disconnected branch lines.)



A

38.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 3 J/C)

B

42.CHECK FOR SHORT IN SUB BUS 1 LINE (ECU, SENSOR)
38.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 3 J/C)
a.

Disconnect the wire harness connector (I117) from the CAN No. 3 junction connector.


b.
C257126C02
0.156,3.313 0.563,3.552 0.406,0.24 2.375,0.26 2.781,0.5 0.406,0.24 2.625,0.969 2.927,0.5 false 2.625,1.177 2.917,1.625 false 1.625,3.146 1.802,2.615 1.802,2.615 1.958,2.615 false 2.365,3.667 2.5,4.146 2.5,4.146 2.646,4.146 false 0.198,2.635 0.51,2.792 0.313,0.156 10 false *1 0.125,0.156 0.438,0.313 0.313,0.156 10 false *a 2.938,0.323 3.427,0.479 0.49,0.156 10 false CANH 2.938,1.635 3.427,1.792 0.49,0.156 10 false CANL 2.021,2.531 2.51,2.688 0.49,0.156 10 false CG 2.708,4.083 3.198,4.24 0.49,0.156 10 false BAT 0.271,3.344 0.76,3.5 0.49,0.156 10 false I39 2.448,0.292 2.938,0.448 0.49,0.156 10 false I116
*1 DLC3
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I116-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I116-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I116-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I116-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

39.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 3 J/C - CAN NO. 4 J/C)

NG

REPLACE CAN NO. 3 JUNCTION CONNECTOR

39.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 3 J/C - CAN NO. 4 J/C)
a.

Reconnect the wire harness connector (I117) to the CAN No. 3 junction connector.


b.

Disconnect the wire harness connector (I120) from the CAN No. 4 junction connector.


c.
C253924C02
2.354,0.167 2.771,0.385 0.417,0.219 0.156,3.281 0.573,3.5 0.417,0.219 2.594,0.969 2.896,0.5 false 2.604,1.188 2.854,1.625 false 1.646,3.104 1.802,2.552 1.802,2.552 1.969,2.552 false 2.354,3.656 2.552,4.135 2.552,4.135 2.719,4.135 false 0.115,2.552 0.427,2.708 0.313,0.156 10 false *1 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 2.427,0.188 3.042,0.385 0.615,0.198 10 false I116 2.906,0.333 3.417,0.552 0.51,0.219 10 false CANH 2.917,1.604 3.427,1.823 0.51,0.219 10 false CANL 2.021,2.469 2.531,2.688 0.51,0.219 10 false CG 2.76,4.052 3.271,4.271 0.51,0.219 10 false BAT 0.271,3.313 0.885,3.51 0.615,0.198 10 false I39
*1 DLC3
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I116-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I116-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I116-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I116-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

40.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 4 J/C)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 4 J/C)

40.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 4 J/C)
a.

Reconnect the wire harness connector (I120) to the CAN No. 4 junction connector.


b.

Disconnect the wire harness connector (I121) from the CAN No. 4 junction connector.


c.
C253924C02
2.354,0.167 2.771,0.385 0.417,0.219 0.156,3.281 0.573,3.5 0.417,0.219 2.594,0.969 2.896,0.5 false 2.604,1.188 2.854,1.625 false 1.646,3.104 1.802,2.552 1.802,2.552 1.969,2.552 false 2.354,3.656 2.552,4.135 2.552,4.135 2.719,4.135 false 0.115,2.552 0.427,2.708 0.313,0.156 10 false *1 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 2.427,0.188 3.042,0.385 0.615,0.198 10 false I116 2.906,0.333 3.417,0.552 0.51,0.219 10 false CANH 2.917,1.604 3.427,1.823 0.51,0.219 10 false CANL 2.021,2.469 2.531,2.688 0.51,0.219 10 false CG 2.76,4.052 3.271,4.271 0.51,0.219 10 false BAT 0.271,3.313 0.885,3.51 0.615,0.198 10 false I39
*1 DLC3
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I116-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I116-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I116-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I116-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

41.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 4 J/C - CAN NO. 5 J/C)

NG

REPLACE CAN NO. 4 JUNCTION CONNECTOR

41.CHECK FOR SHORT IN SUB BUS 1 LINE (CAN NO. 4 J/C - CAN NO. 5 J/C)
a.

Reconnect the wire harness connector (I121) to the CAN No. 4 junction connector.


b.

Disconnect the CAN No. 5 junction connector.


c.
C253924C02
2.354,0.167 2.771,0.385 0.417,0.219 0.156,3.281 0.573,3.5 0.417,0.219 2.594,0.969 2.896,0.5 false 2.604,1.188 2.854,1.625 false 1.646,3.104 1.802,2.552 1.802,2.552 1.969,2.552 false 2.354,3.656 2.552,4.135 2.552,4.135 2.719,4.135 false 0.115,2.552 0.427,2.708 0.313,0.156 10 false *1 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 2.427,0.188 3.042,0.385 0.615,0.198 10 false I116 2.906,0.333 3.417,0.552 0.51,0.219 10 false CANH 2.917,1.604 3.427,1.823 0.51,0.219 10 false CANL 2.021,2.469 2.531,2.688 0.51,0.219 10 false CG 2.76,4.052 3.271,4.271 0.51,0.219 10 false BAT 0.271,3.313 0.885,3.51 0.615,0.198 10 false I39
*1 DLC3
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I116-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I116-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I116-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I116-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 5 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 4 J/C - CAN NO. 5 J/C)

42.CHECK FOR SHORT IN SUB BUS 1 LINE (ECU, SENSOR)
a.

Reconnect the connector for the bus line that is shorted to +B or GND to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short) when it was disconnected).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU to which the bus line shorted to +B or GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C253924C02
2.354,0.167 2.771,0.385 0.417,0.219 0.156,3.281 0.573,3.5 0.417,0.219 2.594,0.969 2.896,0.5 false 2.604,1.188 2.854,1.625 false 1.646,3.104 1.802,2.552 1.802,2.552 1.969,2.552 false 2.354,3.656 2.552,4.135 2.552,4.135 2.719,4.135 false 0.115,2.552 0.427,2.708 0.313,0.156 10 false *1 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 2.427,0.188 3.042,0.385 0.615,0.198 10 false I116 2.906,0.333 3.417,0.552 0.51,0.219 10 false CANH 2.917,1.604 3.427,1.823 0.51,0.219 10 false CANL 2.021,2.469 2.531,2.688 0.51,0.219 10 false CG 2.76,4.052 3.271,4.271 0.51,0.219 10 false BAT 0.271,3.313 0.885,3.51 0.615,0.198 10 false I39
*1 DLC3
*a Component with harness connected
(CAN No. 3 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I116-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I116-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I116-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I116-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

If the resistance becomes normal when the connector is disconnected from the ECU, there may be a short in the ECU.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR

43.CHECK FOR SHORT IN SUB BUS 1 LINE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.
C287982C02
2.323,1.573 2.708,1.781 0.385,0.208 0.219,3.833 0.51,4.042 0.292,0.208 2.792,1.99 2.563,2.146 false 2.792,2.479 2.573,2.333 false 1.781,3.208 1.677,3.208 1.677,3.208 1.594,3.594 false 2.583,4.5 2.438,4.5 2.438,4.5 2.313,4.156 false 0.281,3.26 0.594,3.417 0.313,0.156 10 false *1 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 2.844,1.885 3.427,2.063 0.583,0.177 10 false CANH*b 2.844,2.448 3.427,2.646 0.583,0.198 10 false CANL*b 2.385,1.594 2.75,1.781 0.365,0.188 10 false I116 0.271,3.854 0.542,4.042 0.271,0.188 10 false I39 1.833,3.115 2.198,3.302 0.365,0.188 10 false CG 2.646,4.406 3.073,4.594 0.427,0.188 10 false BAT
*1 DLC3
*a Rear view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I116-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I116-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I116-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I116-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))