Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM2030EQ _58 Vehicle Interior _014664 DOOR LOCK _0074582 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69040A 1.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)

a.
B171377
1.396,3.802 1.396,3.052 1.396,3.052 1.208,3.052 false 0.594,3.802 0.594,3.052 0.594,3.052 0.406,3.052 false 2.146,3.552 2.365,3.719 0.219,0.167 10 false *c 2.677,3.198 2.875,3.406 0.198,0.208 10 false *b 0.083,0.094 0.313,0.302 0.229,0.208 10 false *a 0.281,2.969 0.417,3.135 0.135,0.167 10 false L 1,2.969 1.281,3.156 0.281,0.188 10 false UL
*a Component without harness connected
(Front Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the door lock motor. (for LHD)

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Connection Result
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locks
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocks


If the result is not as specified, replace the front door lock with motor assembly LH.



b.
B171377
1.073,4.198 1.073,4.552 1.073,4.552 1.313,4.552 false 0.906,4.198 0.906,4.552 0.906,4.552 0.708,4.552 false 2.167,3.563 2.406,3.781 0.24,0.219 10 false *c 2.688,3.198 2.927,3.417 0.24,0.219 10 false *b 0.083,0.094 0.354,0.365 0.271,0.271 10 false *a 1.333,4.458 1.51,4.635 0.177,0.177 10 false E 0.229,4.458 0.729,4.635 0.5,0.177 10 false LSSR
*a Component without harness connected
(Front Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the door unlock detection switch. (for LHD)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - 8 (LSSR) Locked 10 kΩ or higher
7 (E) - 8 (LSSR) Unlocked Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly LH.



c.
B273324
2.74,3.552 2.74,3.896 2.74,3.896 2.854,3.896 false 2.427,3.552 2.427,4.115 2.427,4.115 2.854,4.115 false 2.271,3.552 2.271,4.115 2.271,4.115 2.083,4.115 false 2.771,2.052 2.979,2.25 0.208,0.198 10 false *b 2.99,0.969 3.188,1.167 0.198,0.198 10 false *c 0.063,0.063 0.281,0.302 0.219,0.24 10 false *a 2.865,3.833 3.031,4.021 0.167,0.188 10 false E 2.875,4.042 3.042,4.229 0.167,0.188 10 false L 1.833,4.042 2.125,4.229 0.292,0.188 10 false UL
*a Component without harness connected
(Front Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the door key lock and unlock switch. (for LHD)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Locked Below 1 Ω
9 (L) - 7 (E) off 10 kΩ or higher
10 (UL) - 7 (E) Unlocked Below 1 Ω
10 (UL) - 7 (E) off 10 kΩ or higher


If the result is not as specified, replace the front door lock with motor assembly LH.



d.
B171378
0.07,0.063 0.226,0.206 0.156,0.143 10 *a 1.153,3.639 1.302,3.777 0.149,0.138 10 *c 0.61,3.233 0.759,3.371 0.149,0.138 10 *b 2.872,3.822 2.872,3.159 2.872,3.159 3.041,3.159 false 3.064,3.073 3.264,3.21 0.2,0.137 10 UL 2.081,3.822 2.081,3.159 2.081,3.159 2.25,3.159 false 2.274,3.073 2.369,3.21 0.095,0.137 10 L
*a Component without harness connected
(Front Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the door lock motor. (for RHD)

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Connection Result
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locks
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocks


If the result is not as specified, replace the front door lock with motor assembly RH.



e.
B273325
0.07,0.055 0.226,0.199 0.156,0.143 10 *a 1.107,3.18 1.257,3.318 0.149,0.138 10 *c 0.577,2.747 0.726,2.885 0.149,0.138 10 *b 2.3,3.756 2.3,4.121 2.3,4.121 2.181,4.121 false 2.463,3.756 2.463,4.121 2.463,4.121 2.57,4.121 false 2.042,4.039 2.153,4.182 0.111,0.142 10 E 2.613,4.031 2.995,4.173 0.382,0.142 10 LSSR
*a Component without harness connected
(Front Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the door unlock detection switch. (for RHD)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Locked 10 kΩ or higher
7 (LSSR) - 8 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly RH.



f.
B284859
0.75,3.427 0.75,4.438 0.75,4.438 0.906,4.438 false 1.052,3.427 1.052,4.135 1.052,4.135 1.208,4.135 false 1.208,3.427 1.208,3.823 1.208,3.823 1.365,3.823 false 0.958,4.354 1.188,4.552 0.229,0.198 10 false E 1.26,4.042 1.448,4.229 0.188,0.188 10 false L 1.406,3.729 1.646,3.938 0.24,0.208 10 false UL 0.083,0.031 0.271,0.24 0.188,0.208 10 false *a 0.604,1.615 0.833,1.833 0.229,0.219 10 false *b 0.344,0.51 0.573,0.729 0.229,0.219 10 false *c
*a Component without harness connected
(Front Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the door key lock and unlock switch (for RHD).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Locked Below 1 Ω
6 (L) - 8 (E) off 10 kΩ or higher
5 (UL) - 8 (E) Unlocked Below 1 Ω
5 (UL) - 8 (E) off 10 kΩ or higher


If the result is not as specified, replace the front door lock with motor assembly RH.



Hide 69030A 2.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

a.
B171378
2.875,3.823 2.875,3.156 2.875,3.156 3.042,3.156 false 2.083,3.823 2.083,3.156 2.083,3.156 2.25,3.156 false 0.073,0.063 0.271,0.281 0.198,0.219 10 false *a 1.156,3.635 1.396,3.875 0.24,0.24 10 false *c 0.615,3.229 0.833,3.469 0.219,0.24 10 false *b 3.063,3.073 3.323,3.281 0.26,0.208 10 false UL 2.271,3.073 2.417,3.271 0.146,0.198 10 false L
*a Component without harness connected
(Front Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the door lock motor. (for LHD)

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Connection Result
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locks
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocks


If the result is not as specified, replace the front door lock with motor assembly RH.



b.
B273325
2.302,3.76 2.302,4.125 2.302,4.125 2.177,4.125 false 2.458,3.76 2.458,4.125 2.458,4.125 2.573,4.125 false 0.073,0.052 0.313,0.323 0.24,0.271 10 false *a 1.104,3.177 1.302,3.396 0.198,0.219 10 false *c 0.573,2.75 0.792,2.969 0.219,0.219 10 false *b 2.042,4.052 2.24,4.24 0.198,0.188 10 false E 2.615,4.031 3.094,4.271 0.479,0.24 10 false LSSR
*a Component without harness connected
(Front Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the door unlock detection switch. (for LHD)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Locked 10 kΩ or higher
7 (LSSR) - 8 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly RH.



c.
B171377
1.385,3.802 1.385,3.052 1.385,3.052 1.198,3.052 false 0.594,3.802 0.594,3.052 0.594,3.052 0.406,3.052 false 2.146,3.552 2.448,3.792 0.302,0.24 10 false *c 2.677,3.198 2.979,3.438 0.302,0.24 10 false *b 0.083,0.094 0.396,0.344 0.313,0.25 10 false *a 0.281,2.969 0.625,3.24 0.344,0.271 10 false L 1.01,2.969 1.333,3.25 0.323,0.281 10 false UL
*a Component without harness connected
(Front Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the door lock motor. (for RHD)

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Connection Result
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locks
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocks


If the result is not as specified, replace the front door lock with motor assembly LH.



d.
B171377
1.073,4.177 1.073,4.531 1.073,4.531 1.313,4.531 false 0.896,4.177 0.896,4.531 0.896,4.531 0.698,4.531 false 2.167,3.563 2.563,3.823 0.396,0.26 10 false *c 2.688,3.198 3.021,3.479 0.333,0.281 10 false *b 0.083,0.094 0.458,0.417 0.375,0.323 10 false *a 1.344,4.448 1.708,4.625 0.365,0.177 10 false E 0.313,4.448 0.938,4.646 0.625,0.198 10 false LSSR
*a Component without harness connected
(Front Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the door unlock detection switch. (for RHD)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - 8 (LSSR) Locked 10 kΩ or higher
7 (E) - 8 (LSSR) Unlocked Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly LH.