Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM2030EQ _58 Vehicle Interior _014664 DOOR LOCK _0074583 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69060A 1.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH

a.
B164415
1.115,3.813 1.115,3.042 1.115,3.042 1.208,3.042 false 0.583,3.813 0.583,3.042 0.583,3.042 0.677,3.042 false 0.073,0.073 0.427,0.385 0.354,0.313 10 false *a 1.781,3.906 1.99,4.146 0.208,0.24 10 false *c 2.292,3.906 2.573,4.135 0.281,0.229 10 false *b 0.719,2.969 1,3.208 0.281,0.24 10 false L 1.24,2.969 1.573,3.208 0.333,0.24 10 false UL
*a Component without harness connected
(Rear Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the door lock motor.

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Connection Result
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locks
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocks


If the result is not as specified, replace the rear door lock with motor assembly LH.



b.
B164415
1.021,4.073 1.021,4.417 1.021,4.417 1.125,4.417 false 0.677,4.073 0.677,4.417 0.677,4.417 0.573,4.417 false 0.125,0.104 0.271,0.24 0.146,0.135 10 false *a 1.823,3.917 2.094,4.135 0.271,0.219 10 false *c 2.25,3.917 2.583,4.125 0.333,0.208 10 false *b 0.438,4.344 0.813,4.563 0.375,0.219 10 false E 1.146,4.344 1.74,4.563 0.594,0.219 10 false LSSR
*a Component without harness connected
(Rear Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly LH.



Hide 69050A 2.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH

a.
B164416
1.115,3.802 1.115,3 1.115,3 1.021,3 false 0.583,3.802 0.583,3 0.583,3 0.406,3 false 0.115,0.104 0.385,0.375 0.271,0.271 10 false *a 2.083,4.063 2.406,4.302 0.323,0.24 10 false *b 2.417,4.052 2.708,4.26 0.292,0.208 10 false *c 0.781,2.917 1.104,3.167 0.323,0.25 10 false UL 0.292,2.917 0.521,3.135 0.229,0.219 10 false L
*a Component without harness connected
(Rear Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the door lock motor.

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Connection Result
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locks
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocks


If the result is not as specified, replace the rear door lock with motor assembly RH.



b.
B164416
0.677,4.073 0.677,4.427 0.677,4.427 0.5,4.427 false 1.031,4.073 1.031,4.427 1.031,4.427 1.229,4.427 false 0.115,0.094 0.448,0.417 0.333,0.323 10 false *a 1.948,3.969 2.188,4.198 0.24,0.229 10 false *b 2.49,3.969 2.729,4.208 0.24,0.24 10 false *c 1.25,4.354 1.823,4.604 0.573,0.25 10 false LSSR 0.375,4.354 0.635,4.615 0.26,0.26 10 false E
*a Component without harness connected
(Rear Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly RH.