Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074592 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG1 circuit, IG2 circuit or IG hold circuit in the certification ECU (smart key ECU assembly) is detected.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2271 Ignition Hold Monitor Malfunction When either of the following conditions is met (1-trip detection logic*):
·

The IG1 or IG2 circuit in the certification ECU (smart key ECU assembly) is malfunctioning.

·

The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning.


·

AM2 fuse

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation

Turn the engine switch on (IG).


HINT:

To turn the engine switch on (IG), carry the electrical key transmitter sub-assembly and press the engine switch twice with the shift lever in P and the brake pedal released.



*: Only detected while a malfunction is present and the engine switch is on (IG)


HINT:
·

The IG1 and IG2 circuits activate the IG1 and IG2 relays.

·

After the IG1 and IG2 circuits turn on, even if the CPU operates incorrectly, the IG hold circuit maintains the power source mode in on (IG).



Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The engine switch cannot be turned on (IG) (the engine cannot be started). The power source mode cannot be changed to on (IG).

WIRING DIAGRAM

B298799E12
0.042,1.531 0.896,1.719 0.854,0.188 10 false from Battery 1.292,1.688 1.906,2.146 0.615,0.458 10 false AM2 4.958,6.938 5.281,7.167 0.323,0.229 10 false IG2 4.396,7.313 6.177,7.51 1.781,0.198 10 false No. 1 Integration Relay 2.198,1.563 2.563,1.833 0.365,0.271 10 false +B 2.625,1.063 3.125,1.406 0.5,0.344 10 false IG1D 2.635,6.615 3.177,6.917 0.542,0.302 10 false IG2D 2.208,5.896 2.469,6.146 0.26,0.25 10 false E 4.677,4.917 5.479,5.135 0.802,0.219 10 false IG1 NO. 4 3.51,5.375 6.229,5.625 2.719,0.25 10 false Instrument Panel Junction Block Assembly 1.854,7.167 3.427,7.604 1.573,0.438 10 false Certification ECU (Smart Key ECU Assembly) 4.646,3.74 5.448,4.031 0.802,0.292 10 false IG1 NO. 3 4.646,2.573 5.458,2.906 0.813,0.333 10 false IG1 NO. 2 4.656,1.375 5.427,1.646 0.771,0.271 10 false IG1 NO. 1 1.948,1.375 2.115,1.615 0.167,0.24 10 false 2 3.104,6.438 3.323,6.646 0.219,0.208 10 false 9 1.906,5.698 2.135,5.885 0.229,0.188 10 false 11 3.115,0.885 3.302,1.167 0.188,0.281 10 false 6 1.875,1.552 2.24,1.802 0.365,0.25 10 false A43 3.063,1.063 3.396,1.25 0.333,0.188 10 false I78 1.865,5.875 2.24,6.083 0.375,0.208 10 false A43 3.021,6.615 3.438,6.896 0.417,0.281 10 false A43 4.177,6.615 4.51,6.802 0.333,0.188 10 false 1C 5.823,6.615 6.198,6.813 0.375,0.198 10 false 1E 4.229,6.438 4.49,6.656 0.26,0.219 10 false 8 5.875,6.438 6.063,6.594 0.188,0.156 10 false 2 3.583,0.635 3.833,0.823 0.25,0.188 10 false 3E 3.583,0.458 3.854,0.698 0.271,0.24 10 false 3F 3.583,1.052 3.833,1.24 0.25,0.188 10 false 3A 3.594,0.885 3.844,1.083 0.25,0.198 10 false 27 6.198,0.646 6.448,0.833 0.25,0.188 10 false 3D 6.198,0.479 6.615,0.854 0.417,0.375 10 false 33 6.198,1.823 6.542,2.042 0.344,0.219 10 false 3D 6.198,1.656 6.479,1.833 0.281,0.177 10 false 36 6.198,3 6.49,3.229 0.292,0.229 10 false 3C 6.198,2.823 6.479,3.115 0.281,0.292 10 false 33 6.198,4.604 6.51,4.885 0.313,0.281 10 false 3B 6.229,4.438 6.469,4.646 0.24,0.208 10 false 7 5.563,0.802 6.406,1.125 0.844,0.323 10 false BKUP LP 5.625,1.99 6.229,2.375 0.604,0.385 10 false ECU-IG1 NO. 1 3.625,0.292 3.854,0.531 0.229,0.24 10 false 1 3.833,0.771 4.167,1.177 0.333,0.406 10 false *1 3.844,0.521 4.125,0.75 0.281,0.229 10 false *2 0.177,7.073 1.125,7.396 0.948,0.323 10 false *1: for LHD 0.188,7.365 0.948,7.563 0.76,0.198 10 false *2: for RHD 5.625,3.188 6.24,3.594 0.615,0.406 10 false ECU-IG1 NO. 3

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2271
Power Source Control
·

IG1 Relay Monitor (Inside)

·

IG2 Relay Monitor (Inside)

·

Latch Circuit


Starting Control
·

Ignition


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B268625C20
0.091,0.052 0.277,0.214 0.186,0.161 10 *a 0.241,1.304 0.729,1.597 0.487,0.292 0.334,1.362 0.63,1.518 0.296,0.157 10 A43 1.312,1.357 1.1,1.9 false 0.948,1.916 1.147,2.062 0.199,0.146 10 +B
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the A43 connector from the certification ECU (smart key ECU assembly).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-2 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B268625C21
0.24,1.354 0.729,1.646 0.49,0.292 2.042,1.573 2.302,1.979 false 0.094,0.052 0.281,0.208 0.188,0.156 10 false *a 0.344,1.417 0.635,1.573 0.292,0.156 10 false A43 2.323,1.927 2.521,2.073 0.198,0.146 10 false E
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the A43 certification ECU (smart key ECU assembly) connector.

B264896C19
0.302,0.29 0.488,0.451 0.186,0.161 10 *a 4.729,0.887 5.126,1.126 0.397,0.238 4.841,0.934 5.136,1.091 0.296,0.157 10 I78 2.111,0.885 2.508,1.123 0.397,0.238 2.187,0.932 2.482,1.088 0.296,0.157 10 A43 4.388,1.629 4.13,2.287 false 1.978,1.736 1.762,2.287 false 3.927,2.312 4.29,2.468 0.363,0.157 10 IG1D 1.531,2.313 1.894,2.469 0.363,0.157 10 IG2D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-9 (IG2D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher
I78-6 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)