Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074592 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  U0100  Lost Communication with ECM / PCM  U0140  Lost Communication with Main Body ECU  U0155  Lost Communication with Combination Meter  


DESCRIPTION

These DTCs are stored when there is a CAN communication error between the certification ECU (smart key ECU assembly) and the ECM, main body ECU (multiplex network body ECU) or combination meter assembly.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0100 Lost Communication with ECM / PCM CAN communication error between the certification ECU (smart key ECU assembly) and ECM (1-trip detection*) ECM DTC Output Confirmation Operation

Turn the engine switch on (IG) and wait 10 seconds or more.


U0140 Lost Communication with Main Body ECU CAN communication error between the certification ECU (smart key ECU assembly) and main body ECU (1-trip detection*) Main body ECU (multiplex network body ECU) DTC Output Confirmation Operation

Always


U0155 Lost Communication with Combination Meter CAN communication error between the certification ECU (smart key ECU assembly) and combination meter assembly (1-trip detection*) Combination meter assembly DTC Output Confirmation Operation

Turn the engine switch on (IG) and wait 10 seconds or more.



*: Only detected while a malfunction is present and the engine switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
U0100 There is no effect on vehicle behavior. If the following conditions are met, it is determined that the malfunction is not in the direct line (NE) but in CAN communication.
·

When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

·

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.


If the following conditions are met, it is determined that there is a malfunction in both CAN communication and the direct line (NE).
·

When the engine switch is pressed, the engine stops cranking after 6 seconds.

·

When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds.


U0140 Doors cannot be locked or unlocked. The warning (wireless buzzer) does not sound. -
U0155 The warning (meter buzzer) does not sound and the meter does not indicate a warning. -

HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
U0100
U0140
U0155
- -


CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body / Entry&Start / DTC.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK FOR DTC
a.

Note any DTCs that are output.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Body Electrical > Main Body > Trouble Codes
50001 123
Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Proceed to
NEXT



NEXT

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)