When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Security Horn | Security horn | ON/OFF | - |
| Tester Display |
|---|
| Security Horn |
The security horn assembly sounds and stops correctly when operated through the intelligent tester.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the security horn assembly.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY HORN ASSEMBLY>REMOVAL
Check the operation of the security horn assembly.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1 | Horn sounds |
| Battery negative (-) → Horn body |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | S-HORN Relay |
Remove the S-HORN relay from engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Condition | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | When battery voltage is not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | When battery voltage is applied between terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-14 - MB-17 (SH) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Engine room relay block and junction block assembly |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Engine room relay block and junction block assembly S-HORN relay terminal 1- Body ground | Always | 11 to 14 V |
| Engine room relay block and junction block assembly S-HORN relay terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Engine room relay block and junction block assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Engine room relayblock and junctionblock assembly SHORNrelay terminal 3 -A44-1 | Always | Below 1 Ω |
| Engine room relayblock and junctionblock assembly SHORNrelay terminal 3 -Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Engine room relay block and junction block assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Engine room relay block and junction block assembly S-HORN relay terminal 2 - 3D-14 | Always | Below 1 Ω |
| Engine room relay block and junction block assembly S-HORN relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG