Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2012.02–2015.04
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074602 ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  B2780  Push Switch / Key Unlock Warning Switch Malfunction  


DESCRIPTION

This DTC is stored if the transponder key ECU assembly does not detect that the unlock warning switch assembly is ON even when the key is in the ignition key cylinder. Under normal conditions, the unlock warning switch assembly is ON when the key is in the ignition key cylinder.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2780 Push Switch / Key Unlock Warning Switch Malfunction "Unlock warning switch ON" is not detected when the key is in the ignition key cylinder.
·

Wire harness or connector

·

Unlock warning switch assembly

·

Transponder key ECU assembly



WIRING DIAGRAM

B278950E01
2.165,0.988 4.259,1.13 2.094,0.142 10 Unlock Warning Switch Assembly 2.165,0.827 2.46,0.983 0.295,0.156 10 I33 5.38,1.793 6.809,2.116 1.429,0.323 10 Transponder Key ECU Assembly 5.38,1.632 5.655,1.788 0.274,0.156 10 I19 5.647,0.546 6.004,0.703 0.358,0.156 10 KSW 3.375,0.455 3.674,0.612 0.299,0.156 10 UN+ 2.676,0.455 2.976,0.612 0.299,0.156 10 UN- 5.479,0.469 5.607,0.626 0.128,0.156 10 3 3.741,0.455 3.87,0.612 0.128,0.156 10 1 2.501,0.455 2.63,0.612 0.128,0.156 10 2

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Immobiliser > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key SW Unlock warning switch signal ON or OFF ON: Key in ignition key cylinder
OFF: No key in ignition key cylinder
-
Body Electrical > Immobiliser > Data List
Tester Display
Key SW
50003 260 3
OK:

On the intelligent tester screen, the item changes between ON and OFF according to the chart above.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.
B203483C03
0.063,0.031 0.219,0.177 0.156,0.146 10 *a 0.396,0.26 0.552,0.406 0.156,0.146 10 *b 0.396,0.781 0.552,0.927 0.156,0.146 10 *c
*a Component without harness connected
(Unlock Warning Switch Assembly)
*b Free
*c Pushed


Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pushed
(Key set)
Below 1 Ω
1 - 2 Free
(Key removed)
10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - TRANSPONDER KEY ECU AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - TRANSPONDER KEY ECU AND BODY GROUND)
a.

Disconnect the transponder key ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I19-3 (KSW) - I33-1 (UN+) Always Below 1 Ω
I19-3 (KSW) - Body ground Always 10 kΩ or higher
I33-2 (UN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR