Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2012.02–2015.04
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074602 ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

The transponder key coil is built into the transponder key amplifier and receives a key code signal from the transponder chip in the key. This signal is amplified by the amplifier, then it is output to the transponder key ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2784 Antenna Coil Open / Short Antenna coil is open/shorted.
·

Wire harness or connector

·

Transponder key amplifier

·

Transponder key ECU assembly



WIRING DIAGRAM

B193467E08
5.338,2.618 6.794,2.929 1.456,0.312 10 Transponder Key ECU Assembly 5.338,2.437 5.628,2.612 0.29,0.175 10 I19 1.029,2.981 1.319,3.156 0.29,0.175 10 I34 1.029,3.167 2.721,3.341 1.692,0.175 10 Transponder Key Amplifier 1.878,2.485 2.497,2.659 0.619,0.175 10 Amplifier 5.433,0.743 5.638,0.911 0.205,0.168 10 14 3.23,0.743 3.358,0.911 0.128,0.168 10 1 5.433,1.148 5.638,1.316 0.205,0.168 10 15 3.23,1.148 3.358,1.316 0.128,0.168 10 4 5.517,1.539 5.639,1.707 0.122,0.168 10 4 3.23,1.539 3.358,1.707 0.128,0.168 10 5 5.517,1.935 5.639,2.103 0.122,0.168 10 5 3.23,1.935 3.358,2.103 0.128,0.168 10 7 5.698,2.01 6.155,2.182 0.457,0.172 10 AGND 5.698,1.638 6.115,1.81 0.417,0.172 10 TXCT 5.698,1.235 6.155,1.407 0.457,0.172 10 CODE 5.698,0.834 6.031,1.005 0.333,0.172 10 VC5 2.724,1.941 3.18,2.113 0.457,0.172 10 AGND 2.754,1.543 3.171,1.714 0.417,0.172 10 TXCT 2.714,1.146 3.17,1.318 0.457,0.172 10 CODE 1.421,0.942 1.848,1.114 0.427,0.172 10 ANT1 1.421,2.132 1.848,2.303 0.427,0.172 10 ANT2 0.858,1.44 1.183,1.612 0.325,0.172 10 Coil 2.839,0.748 3.171,0.92 0.333,0.172 10 VC5

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Immobiliser > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Antenna Coil Status Transponder key amplifier coil condition Normal or Fail Normal: Antenna coil normal
Fail: Antenna coil malfunctioning
-
Body Electrical > Immobiliser > Data List
Tester Display
Antenna Coil Status
50003 260 5
OK:

On the intelligent tester screen, "Normal" is displayed.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)
2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)
a.

Disconnect the transponder key ECU assembly connector.


b.

Disconnect the transponder key amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I19-4 (TXCT) - I34-5 (TXCT) Always Below 1 Ω
I19-5 (AGND) - I34-7 (AGND) Always Below 1 Ω
I19-14 (VC5) - I34-1 (VC5) Always Below 1 Ω
I19-15 (CODE) - I34-4 (CODE) Always Below 1 Ω
I19-4 (TXCT) - Body ground Always 10 kΩ or higher
I19-5 (AGND) - Body ground Always 10 kΩ or higher
I19-14 (VC5) - Body ground Always 10 kΩ or higher
I19-15 (CODE) - Body ground Always 10 kΩ or higher
I34-5 (TXCT) - Body ground Always 10 kΩ or higher
I34-7 (AGND) - Body ground Always 10 kΩ or higher
I34-1 (VC5) - Body ground Always 10 kΩ or higher
I34-4 (CODE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSPONDER KEY AMPLIFIER (POWER SOURCE AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSPONDER KEY AMPLIFIER (POWER SOURCE AND BODY GROUND)
a.

Reconnect the transponder key ECU assembly connector.


b.
B203486C04
1.469,0.271 1.896,0.552 0.427,0.281 1.458,1.219 1.458,1.906 1.458,1.906 1.677,1.906 false 1.271,1.104 0.833,1.104 0.833,1.104 0.833,1.823 false 0.094,0.083 0.385,0.354 0.292,0.271 10 *a 0.625,1.844 1.167,2.063 0.542,0.219 10 AGND 1.708,1.823 2.115,2.083 0.406,0.26 10 VC5 1.583,0.333 1.948,0.531 0.365,0.198 10 I19
*a Component with harness connected
(Transponder Key ECU Assembly)


Reconnect the transponder key amplifier connector.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I19-14 (VC5) - Body ground No key in ignition key cylinder Below 1 V
I19-14 (VC5) - Body ground Key in ignition key cylinder 4.6 to 5.4 V


Standard Resistance:
Tester Connection Condition Specified Condition
I19-5 (AGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY