Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2012.02–2015.04
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074602 ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Immobiliser > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key SW Unlock warning switch signal ON or OFF ON: Key in ignition key cylinder
OFF: No key in ignition key cylinder
-
IG SW Ignition switch signal ON or OFF ON: Ignition switch ON or engine start
OFF: Ignition switch ACC or off
-
Immobiliser Immobiliser system status Set or Unset Set: No key in ignition key cylinder, or 20 sec. elapsed after turning the ignition switch to on (ACC) or off
Unset: Key in ignition key cylinder
-
Response Transponder chip data NG or OK NG: Data error
OK: Data OK
-
Frame Error Transponder chip data NG or OK NG: Data error
OK: Data OK
-
Different Serial Number Transponder chip data NG or OK NG: Data error
OK: Data OK
-
Different Encrypt Code Transponder chip data NG or OK NG: Data error
OK: Data OK
-
Abnormal Status Transponder chip data NG or OK NG: Data error
OK: Data OK
-
Bcc Malfunction Transponder chip data NG or OK NG: Incorrect data being sent
OK: Correct data being sent
-
Sub Key Sub key code signal Reg or Unreg Reg: Registered sub key code sent
Unreg: Unmatching sub key code sent
-
Master Key Master key code signal Reg or Unreg Reg: Registered master key code sent
Unreg: Unmatching master key code sent
-
Transponder S-code Number of registered sub key min. 0, max. 15 Number of registered sub key -
Transponder M-code Number of registered master key min. 0, max. 15 Number of registered master key -
+B Power source Break or Normal Break: Power source open
Normal: Power source normal
-
Antenna Coil Status Transponder key amplifier coil condition Normal or Fail Normal: Antenna coil normal
Fail: Antenna coil malfunctioning
-
E/G Start Permission Engine start permission OK or NG OK: Engine start permitted
NG: Engine start not permitted
-
Immobi ECU Comm Spd Immobiliser ECU communication speed Unknown, 50bps, 200bps or No Res Unknown: ECU communication speed unknown
50bps: ECU communication speed 50 bps
200bps: ECU communication speed 200 bps
No Res: ECU communication speed no response
-
The Number of DTCs Number of DTCs Min.: 0, Max.: 255 Number of stored DTCs -


ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser or Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security Indicator Light OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light OFF/ON -