Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2012.02–2015.04
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074602 ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

·

The transponder key ECU assembly blinks the security indicator light when the immobiliser is set (no key is in the ignition key cylinder).

·

The main body ECU (multiplex network body ECU) blinks the security indicator light when the theft deterrent system is in the arming preparation state or alarm sounding state.


WIRING DIAGRAM

B271008E18
4.49,1.115 4.802,1.271 0.313,0.156 10 false I19 4.448,2.969 4.719,3.125 0.271,0.156 10 false I12 4.49,1.281 5.938,1.76 1.448,0.479 10 false Transponder Key ECU Assembly 4.448,3.115 6.146,3.573 1.698,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 0.917,1.125 1.281,1.375 0.365,0.25 10 false I56 0.917,1.292 3.365,1.865 2.448,0.573 10 false Security Indicator Light (Air Conditioning Control Assembly) 4.771,0.583 5.198,0.844 0.427,0.26 10 false IND 2.448,0.615 2.656,0.781 0.208,0.167 10 false LP 1.719,0.615 2.167,0.781 0.448,0.167 10 false GND 4.771,2.5 5.156,2.74 0.385,0.24 10 false IND 4.563,0.479 4.719,0.635 0.156,0.156 10 false 8 4.5,2.365 4.802,2.635 0.302,0.271 10 false 22 2.74,0.479 2.948,0.635 0.208,0.156 10 false 1 1.521,0.479 1.76,0.677 0.24,0.198 10 false 6 3.604,1.792 4.01,2.135 0.406,0.344 10 false *1 0.75,2.958 2.646,3.135 1.896,0.177 10 false *1: w/ Theft Deterrent System

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser or Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light OFF/ON -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Security Indicator
50004 123 19
Result:
Result Proceed to
Security indicator light operation is normal when performing the "Main Body" and "Immobiliser" Active Test A
·

Security indicator light operation is not normal when performing the "Immobiliser" Active Test

·

Security indicator light operation is normal when performing the "Main Body" Active Test


B
·

Security indicator light operation is normal when performing the "Immobiliser" Active Test

·

Security indicator light operation is not normal when performing the "Main Body" Active Test


C
Security indicator light operation is not normal when performing the "Main Body" and "Immobiliser" Active Test D




A

2.CHECK SECURITY INDICATOR LIGHT OPERATION

B

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - TRANSPONDER KEY ECU ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

D

5.CHECK HARNESS AND CONNECTOR
2.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

When the immobiliser is set, check that the security indicator light blinks.*1

OK:

The security indicator light blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light on.*2

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION

OK:

The security indicator light is on normally.


Result:
Result Proceed to
Both *1 and *2 are OK A
*1 is NG (*2 is OK) B
*2 is NG (*1 is OK) C
Both *1 and *2 are NG D




A

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

D

REPLACE SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD)

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the security indicator light (heater control switch board) connector.


b.

Disconnect the transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I19-8 (IND) - I56-1 (LP) Always Below 1 Ω
I19-8 (IND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the security indicator light (heater control switch board) connector.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-22 (IND) - I56-1 (LP) Always Below 1 Ω
I12-22 (IND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR
a.

Disconnect the security indicator light (heater control switch board) connector.


b.

Disconnect transponder key ECU assembly connector.


c.

Disconnect the main body ECU (multiplex network body ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I19-8 (IND) - I56-1 (LP) Always Below 1 Ω
I12-22 (IND) - I56-1 (LP) Always Below 1 Ω
I56-1 (LP) - Body ground Always 10 kΩ or higher
I56-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD)
a.

Temporarily replace the security indicator light (heater control switch board) with a new or known good one.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL


b.

When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.



Result:
Proceed to
OK
NG



OK

END (HEATER CONTROL SWITCH BOARD WAS DEFECTIVE)

NG

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY
7.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new or known good one.

HINT:

Refer to to Service Bulletin.



b.

When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)