Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › 2012.02–2015.04
RM2030EQ _58 Vehicle Interior _014669 SUPPLEMENTAL RESTRAINT SYSTEMS _0074621 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the 3 spoke and 4 spoke.

·

The procedure listed below is for the 3 spoke.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 45187 3.REMOVE LOWER NO. 3 STEERING WHEEL COVER

a.
B289010

Disengage the claw and guide to remove the lower No. 3 steering wheel cover.


Hide 45186 4.REMOVE LOWER NO. 2 STEERING WHEEL COVER

a.
B289011

Disengage the claw and guide to remove the lower No. 2 steering wheel cover.


Hide 45130 5.REMOVE HORN BUTTON ASSEMBLY

CAUTION:

When storing the horn button assembly, keep the airbag deployment side facing upward.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B289012C01
0.667,1.49 0.906,1.49 true 0.948,1.417 1.156,1.615 0.208,0.198 10 true *1
*1 Torsion Spring


Using a screwdriver, push up the torsion spring to disengage the pin.

HINT:

Insert the screwdriver from the installation hole of the lower No. 3 steering wheel cover.



d.
B289013C01
1.635,0.729 1.25,0.729 true 1.063,0.646 1.26,0.823 0.198,0.177 10 false *1
*1 Torsion Spring


Using a screwdriver, push in the 2 torsion springs to disengage the 2 pins.

NOTICE:

Do not drop the horn button assembly.


HINT:

Insert the screwdriver from the installation holes in the lower No. 3 steering wheel cover and lower No. 2 steering wheel cover.



e.

Pull out the horn button assembly from the steering wheel assembly and support the horn button assembly with one hand.

NOTICE:

When removing the horn button assembly, do not pull the airbag wire harness.



f.
B289014C01
1.781,1.969 0.375,1.969 true 0.281,2.281 1.396,2.281 1.396,2.281 1.573,2.115 true 2.594,0.323 2.479,0.219 2.479,0.219 2.333,0.219 true 2.313,2.448 2.313,2.708 2.313,2.708 2.49,2.708 true 0.188,1.906 0.396,2.104 0.208,0.198 10 false *1 0.094,2.208 0.292,2.417 0.198,0.208 10 false *2 2.521,2.635 2.729,2.844 0.208,0.208 10 true *3 2.135,0.156 2.365,0.333 0.229,0.177 10 false *4
*1 Protective Tape
*2 Airbag Connector
*3 Horn Connector
*4 Airbag Connector Lock


Disconnect the horn connector from the horn button assembly.


g.

Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock.


h.

Disconnect the airbag connector to remove the horn button assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.