Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR
RM2030EQ _58 Vehicle Interior _014672 HEATING / AIR CONDITIONING _0074666 COMPRESSOR G

HEATING / AIR CONDITIONING  COMPRESSOR  INSPECTION  


PROCEDURE

Hide 88320 1.INSPECT COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)

a.
E167398
1.458,1.167 1.938,1.5 0.479,0.333 1.906,2.177 2.5,2.177 false 1.5,2.188 0.875,2.188 false 0.167,0.167 0.635,0.438 0.469,0.271 10 false *a 1.573,1.24 2.135,1.51 0.563,0.271 10 false E73 2.531,2.083 3.063,2.458 0.531,0.375 10 false SSR+ 0.5,2.094 1.094,2.396 0.594,0.302 10 false SSR-
*a Component without harness connected
(Cooler Compressor Assembly (A/C Lock Sensor))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E73-1 (SSR+)- E73-2 (SSR-) 20°C (68°F) 160 to 320 Ω


If the resistance is not as specified, replace the cooler compressor assembly.


Hide 88320 2.INSPECT COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID)

a.
E229635
2.49,1.677 2.927,1.969 0.438,0.292 1.49,2.01 1.229,2.542 false 1.969,2 2.302,2.542 false 0.167,0.167 0.51,0.406 0.344,0.24 10 false *a 2.583,1.74 3.052,2.031 0.469,0.292 10 false E74 2.198,2.563 2.75,2.875 0.552,0.313 10 false SOL- 1.052,2.563 1.667,2.875 0.615,0.313 10 false SOL+
*a Component without harness connected
(Cooler Compressor Assembly (Compressor Solenoid))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E74-1 (SOL-) - E74-2 (SOL+) 20°C (68°F) 10 to 11 Ω


If the resistance is not as specified, replace the cooler compressor assembly.


Hide 88320 3.INSPECT COOLER COMPRESSOR ASSEMBLY

a.

Disconnect the E73 cooler compressor assembly connector.


b.
E228787
1.5,0.115 1.958,0.396 0.458,0.281 1.5,2.01 1.958,2.292 0.458,0.281 1.75,1.375 2.615,1.375 false 1.604,0.167 2.052,0.396 0.448,0.229 10 false E73 1.646,2.063 2.146,2.385 0.5,0.323 10 false a2 2.646,1.292 3.156,1.552 0.51,0.26 10 false MG+ 0.333,0.177 0.75,0.417 0.417,0.24 10 false *a 0.333,2 0.75,2.313 0.417,0.313 10 false *b
*a Component without harness connected
(Cooler Compressor Assembly)
*b Component without harness connected
(Magnetic Clutch Assembly)


Disconnect the a2 magnetic clutch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E73-3 (MG+) - a2-1 Always Below 1 Ω
E73-3 (MG+) - Body ground Always 10 kΩ or higher


If the resistance is not as specified, replace the cooler compressor assembly.


Hide 88410 4.INSPECT MAGNETIC CLUTCH ASSEMBLY

a.
E167401
0.813,1.781 1.229,2.042 0.417,0.26 0.333,0.333 0.792,0.583 0.458,0.25 10 false *a 0.948,1.823 1.333,2.073 0.385,0.25 10 false a2
*a Component without harness connected
(Magnetic Clutch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a2-1 - Body ground 20°C (68°F) 3.8 to 4.2 Ω


If the resistance is not as specified, replace the magnetic clutch assembly.


b.

When connector terminal a2-1 is connected to a positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch operating sound can be heard, and 2) the magnetic clutch hub and rotor lock.

OK:
1):

The magnetic clutch's operating sound can be heard.

2):

The magnetic clutch's hub and rotor lock.


If the result is not as specified, replace the magnetic clutch assembly.