Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM2030EQ _59 Vehicle Exterior _014675 WINDOW / GLASS _0074675 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor assembly (for driver door) is operated by the power window regulator master switch assembly. The power window regulator motor assembly (for driver door) has motor, regulator and ECU functions.

This DTC is stored when the ECU built into the regulator motor determines that the power window regulator master switch assembly is stuck.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2312 Power Window Switch Malfunction
·

Power window regulator master switch assembly (for driver door) stuck

·

Power window regulator master switch assembly held in same position for more than 20 seconds


·

Power window regulator master switch assembly

·

Power window regulator motor assembly (for driver door)

·

Wire harness or connector



WIRING DIAGRAM

B281016E32
0.458,2.281 2.094,2.719 1.635,0.438 10 false Main Body ECU (Multiplex Network Body ECU) 0.938,3.365 2.583,3.521 1.646,0.156 10 false : LIN Communication Line 0.49,0.531 1.51,0.854 1.021,0.323 10 false from Battery 1.74,0.708 2.604,0.865 0.865,0.156 10 false DOOR NO. 2 2.521,2.438 4.479,2.823 1.958,0.385 10 false Power Window Regulator Motor Assembly (for Driver Door) 5.229,2.427 6.823,2.802 1.594,0.375 10 false Power Window Regulator Master Switch Assembly 6.177,3.135 6.917,3.333 0.74,0.198 10 false *1: for LHD 6.177,3.427 6.927,3.625 0.75,0.198 10 false *2: for RHD 2.521,2.281 3.354,2.542 0.833,0.26 10 false K9*1, J9*2 5.229,2.271 6.313,2.604 1.083,0.333 10 false K10*1, J10*2 1.615,1.604 2.021,1.875 0.406,0.271 10 false LIN2 2.833,1.438 3.094,1.594 0.26,0.156 10 false LIN 2.833,0.427 2.958,0.583 0.125,0.156 10 false B 3.771,0.448 4.177,0.604 0.406,0.156 10 false AUTO 5.375,0.531 5.51,0.688 0.135,0.156 10 false A 5.375,1.052 5.51,1.208 0.135,0.156 10 false D 5.375,1.531 5.51,1.688 0.135,0.156 10 false U 5.375,1.833 5.51,1.99 0.135,0.156 10 false E 3.76,0.948 4.198,1.104 0.438,0.156 10 false DWN1 3.865,1.458 4.167,1.615 0.302,0.156 10 false UP1 4.031,1.75 4.156,1.906 0.125,0.156 10 false E 4.25,1.75 4.375,1.906 0.125,0.156 10 false 1 4.25,0.948 4.375,1.104 0.125,0.156 10 false 7 5.198,0.958 5.531,1.26 0.333,0.302 10 false 5 4.792,1.438 5.594,1.844 0.802,0.406 10 false 8*1, 1*2 4.792,1.74 5.583,2.083 0.792,0.344 10 false 1*1, 9*2 4.25,0.448 4.375,0.604 0.125,0.156 10 false 4 5.188,0.448 5.469,0.802 0.281,0.354 10 false 4 4.24,1.458 4.427,1.615 0.188,0.156 10 false 10 2.646,0.438 2.771,0.594 0.125,0.156 10 false 2 2.625,1.438 2.75,1.594 0.125,0.156 10 false 9


CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2312 can be stored in the power window regulator motor assembly (for driver door).

·

If a power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear the DTC.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Clear DTCs
50002 124

b.

Check for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124
OK:

DTC B2312 is not output.



Result:
Proceed to
OK
NG



OK

END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

NG

2.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
2.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal ON or OFF ON: Driver door power window auto switch operated
OFF: Driver door power window auto switch not operated
-
D Door P/W Up SW Driver door power window manual up switch signal ON or OFF ON: Driver door power window manual up switch operated
OFF: Driver door power window manual up switch not operated
-
D Door P/W Down SW Driver door power window manual down switch signal ON or OFF ON: Driver door power window manual down switch operated
OFF: Driver door power window manual down switch not operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Auto SW
D Door P/W Up SW
D Door P/W Down SW
50003 124 1,2,3
OK:

On the intelligent tester screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
a.

Disconnect the power window regulator master switch assembly connector.


b.

Disconnect the power window regulator motor assembly (for driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K10-8 (U) - Body ground Always 10 kΩ or higher
K10-5 (D) - Body ground Always 10 kΩ or higher
K10-4 (A) - Body ground Always 10 kΩ or higher
K9-10 (UP1) - Body ground Always 10 kΩ or higher
K9-7 (DWN1) - Body ground Always 10 kΩ or higher
K9-4 (AUTO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
J10-1 (U) - Body ground Always 10 kΩ or higher
J10-5 (D) - Body ground Always 10 kΩ or higher
J10-4 (A) - Body ground Always 10 kΩ or higher
J9-10 (UP1) - Body ground Always 10 kΩ or higher
J9-7 (DWN1) - Body ground Always 10 kΩ or higher
J9-4 (AUTO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B164359
2.365,1.781 2.635,2.698 false 1.906,1.792 2.125,2.688 false 1.677,1.792 1.458,2.698 false 1.208,1.792 0.917,2.688 false 1.073,1.771 0.656,2.396 false 0.188,0.188 0.479,0.406 0.292,0.219 10 *a 0.792,2.698 1.104,2.938 0.313,0.24 10 U*A 1.406,2.698 1.542,2.885 0.135,0.188 10 D 2.094,2.698 2.229,2.885 0.135,0.188 10 A 2.573,2.708 3.281,3.073 0.708,0.365 10 E*A,U*B 0.479,2.438 0.792,2.677 0.313,0.24 10 E*B
*A for LHD
*B for RHD
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
8 (U) - 1 (E) Released 10 kΩ or higher
8 (U) - 4 (A) Released 10 kΩ or higher
4 (A) - 1 (E) Released 10 kΩ or higher
5 (D) - 1 (E) Released 10 kΩ or higher
4 (A) - 5 (D) Released 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
1 (U) - 9 (E) Released 10 kΩ or higher
1 (U) - 4 (A) Released 10 kΩ or higher
4 (A) - 9 (E) Released 10 kΩ or higher
5 (D) - 9 (E) Released 10 kΩ or higher
4 (A) - 5 (D) Released 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY