Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM2030EQ _59 Vehicle Exterior _014676 SLIDING ROOF / CONVERTIBLE _0074687 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2341  Sensor (Motor) Failure  B2344  Position Failure  


DESCRIPTION

When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored.

When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a gear position malfunction and the sliding roof operation is stopped, DTC B2344 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2341 Sensor (Motor) Failure Sensor (motor) failure (When the sliding roof ECU enters fail-safe mode due to a problem with the motor)
·

Sliding roof ECU (Sliding roof drive gear sub-assembly)

·

Sliding roof switch (Roof console box assembly)

·

Wire harness or connector


B2344 Position Failure Position failure (When the sliding roof ECU enters fail-safe mode due to a problem with the gear position)
·

Sliding roof ECU (Sliding roof drive gear sub-assembly)

·

Sliding roof switch (Roof console box assembly)

·

Wire harness or connector



WIRING DIAGRAM

B271000E10
4.667,4.906 6.635,5.24 1.969,0.333 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly) 4.667,4.76 4.99,4.938 0.323,0.177 10 false S4 1.833,4.385 5.021,4.646 3.188,0.26 10 false Sliding Roof Switch (Roof Console Box Assembly) 1.833,4.208 2.115,4.385 0.281,0.177 10 false S7 5.052,2.802 5.385,2.948 0.333,0.146 10 false OPN 5.052,3.042 5.385,3.177 0.333,0.135 10 false CLS 5.052,3.802 5.281,3.958 0.229,0.156 10 false UP 5.052,3.552 5.583,3.729 0.531,0.177 10 false DWN 4.896,2.698 5.031,2.875 0.135,0.177 10 false 7 4.896,2.958 5.031,3.135 0.135,0.177 10 false 5 4.896,3.458 5.031,3.635 0.135,0.177 10 false 6 4.896,3.708 5,3.885 0.104,0.177 10 false 4 3.75,2.698 4.083,2.844 0.333,0.146 10 false OPN 3.792,2.958 4.281,3.302 0.49,0.344 10 false CLS 3.615,3.458 4.208,3.771 0.594,0.313 10 false DOWN 3.875,3.708 4.229,4.031 0.354,0.323 10 false UP 4.156,2.698 4.26,2.875 0.104,0.177 10 false 3 4.156,2.958 4.26,3.135 0.104,0.177 10 false 2 4.156,3.708 4.25,3.885 0.094,0.177 10 false 5 4.156,3.458 4.271,3.635 0.115,0.177 10 false 4 2.427,3.042 2.854,3.271 0.427,0.229 10 false GND 2.25,3.042 2.438,3.219 0.188,0.177 10 false 1 5.813,4.115 6.115,4.427 0.302,0.313 10 false E 6.01,4 6.219,4.177 0.208,0.177 10 false 12 2.719,0.979 4.417,1.313 1.698,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 0.875,0.979 2.073,1.375 1.198,0.396 10 false Combination Meter Assembly 3.667,0.542 4,0.708 0.333,0.167 10 false LIN2 2.99,0.542 3.354,0.708 0.365,0.167 10 false CAN 1.656,0.542 2.021,0.708 0.365,0.167 10 false CAN 5.063,0.542 5.74,0.906 0.677,0.365 10 false MPX1 0.688,5.458 2.333,5.646 1.646,0.188 10 false : LIN Communication Line 0.688,5.135 2.427,5.323 1.74,0.188 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, it requires initialization (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).

·

The sliding roof system uses the CAN and LIN communication systems. First, confirm that there are no malfunctions in the CAN and LIN communication systems. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK SLIDING ROOF OPERATION
a.

Check the sliding roof auto operation.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>OPERATION CHECK

OK:

Auto operation operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK DTC OUTPUT

NG

3.INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
2.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Recheck for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147
OK:

DTC B2341 or B2344 is not output.



Result:
Proceed to
OK
NG



OK

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

3.INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

Check that the sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

OK:

Sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT

NG

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH AND BODY GROUND)
4.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Recheck for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147
OK:

DTC B2341 or B2344 is not output.



Result:
Proceed to
OK
NG



OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH AND BODY GROUND)
a.

Disconnect the S7 sliding roof switch (roof console box assembly) connector.


b.

Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S4-5 (CLS) - S7-2 (CLS) Always Below 1 Ω
S4-5 (CLS) - Body ground Always 10 kΩ or higher
S4-7 (OPN) - S7-3 (OPN) Always Below 1 Ω
S4-7 (OPN) - Body ground Always 10 kΩ or higher
S4-6 (DWN) - S7-4 (DOWN) Always Below 1 Ω
S4-6 (DWN) - Body ground Always 10 kΩ or higher
S4-4 (UP) - S7-5 (UP) Always Below 1 Ω
S4-4 (UP) - Body ground Always 10 kΩ or higher
S7-1 (GND) - Body ground Always Below 1 Ω
S4-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY)
a.
B270995C05
0.514,3.003 0.687,3.163 0.174,0.16 10 *a 1.362,3.272 1.578,3.425 0.215,0.153 10 UP 1.183,3.031 1.648,3.184 0.465,0.153 10 DOWN 2.206,3.031 2.529,3.184 0.323,0.153 10 OPN 2.336,3.272 2.659,3.425 0.323,0.153 10 CLS 2.641,3.803 2.991,3.955 0.351,0.153 10 GND 1.788,3.838 1.788,3.351 1.788,3.351 1.626,3.351 false 2.142,3.838 2.142,3.351 2.142,3.351 2.303,3.351 false 2.026,3.838 2.026,3.107 2.026,3.107 2.171,3.107 false 1.896,3.838 1.896,3.107 1.896,3.107 1.751,3.107 false 2.298,3.885 2.62,3.885 false
*a Component without harness connected
(Sliding Roof Switch (Roof Console Box Assembly))


Remove the sliding roof switch (roof console box assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (UP) - 1 (GND) UP switch is pressed Below 1 Ω
5 (UP) - 1 (GND) UP switch is not pressed 10 kΩ or higher
4 (DOWN) - 1 (GND) DOWN switch is pressed Below 1 Ω
4 (DOWN) - 1 (GND) DOWN switch is not pressed 10 kΩ or higher
3 (OPN) - 1 (GND) OPEN switch is pressed Below 1 Ω
3 (OPN) - 1 (GND) OPEN switch is not pressed 10 kΩ or higher
2 (CLS) - 1 (GND) CLOSE switch is pressed Below 1 Ω
2 (CLS) - 1 (GND) CLOSE switch is not pressed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPLACE SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY)