Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2012.02–2015.04
RM2030EQ _59 Vehicle Exterior _014677 DOOR / HATCH _0074691 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 75976G 3.INSTALL FRONT DOOR LOWER OUTSIDE STRIPE

Hide 75754A 5.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 75756C 6.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

Hide 75720 7.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY

Hide 67481C 8.INSTALL FRONT DOOR FRONT LOWER FRAME SEAL

a.
B280379

Install the front door front lower frame seal.


Hide 67001A 9.INSTALL FRONT DOOR PANEL CUSHION

a.
B281738

Engage the 2 claws to install 2 new front door panel cushions.


Hide 67864B 10.INSTALL FRONT DOOR NO. 2 WEATHERSTRIP

a.
B281737

Engage the 8 clips to install the front door No. 2 weatherstrip.


Hide 67664C 11.INSTALL DOOR FRAME GARNISH

a.
B277197

Engage the clip to install a new door frame garnish.


Hide 67862 12.INSTALL FRONT DOOR WEATHERSTRIP

a.
B281736

Engage the 19 clips and install the front door weatherstrip.


Hide 68620 13.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding areas of the front door check assembly.


b.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
B280375E01
2.906,1.229 3.24,1.583 0.333,0.354 10 false (A) 1.885,0.74 2.292,1.104 0.406,0.365 10 false (B) 2.01,1.396 2.375,1.75 0.365,0.354 10 false (B)

Install the front door check assembly with the 3 bolts.

Torque:
Bolt (A) : 29 N*m (296 kgf*cm, 21 ft.*lbf)
Bolt (B) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 69312 14.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B280373E01
1.625,0.375 2.063,0.438 false 2.76,0.677 3.063,0.948 0.302,0.271 10 false (1) 1.417,0.281 1.771,0.615 0.354,0.333 10 false (2)

Install the front door lock open rod as indicated by the arrows and in the order shown in the illustration.


Hide 82186B 15.INSTALL FRONT DOOR WIRE (w/ Smart Entry and Start System)

a.
B280372

Engage the 3 clamps to install the front door wire.


Hide 69202A 16.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


b.
B280371C06
0.698,1.708 0.406,1.865 false 0.229,1.813 0.448,2.073 0.219,0.26 10 false *1 0.083,0.146 0.365,0.417 0.281,0.271 10 false *a 0.083,2.5 0.365,2.802 0.281,0.302 10 false *b
*1 Door Handle Nut
*a Outside
*b Inside


Engage the claw.


c.

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw and door handle nut.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

w/ Smart Entry and Start System:

i.
B280369

Engage the 3 clamps.


ii.

Connect the connector.



Hide 69760C 17.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B280368

Install the front door inside locking cable assembly.


b.
B280366

Engage the 3 claws.


Hide 69720B 18.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B280365

Install the front door lock remote control cable assembly.


Hide 69040A 19.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing the removed front door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

·

Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door with motor lock assembly.



a.

Apply MP grease to the sliding parts of the front door lock with motor assembly.


b.

When reusing the front door lock with motor assembly:

i.
B280363

Install a new door lock wiring harness seal to the front door lock with motor assembly.



c.
B280362C10
2.979,2.615 3.104,2.75 false 3.135,2.677 3.427,2.99 0.292,0.313 10 false *1
*1 Front Door Lock Open Rod


Insert the front door lock open rod to the front door lock with motor assembly.


d.

Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.


e.

Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 69242E 20.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B280360

Engage the 2 claws to install the front door rear outside handle pad.


Hide 69241H 21.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B280359

Engage the 3 claws to install the front door front outside handle pad.


Hide 69220 22.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B280358

Insert the front end of the front door outside handle assembly into the front door outside handle frame.


b.

Insert the rear end of the front door outside handle assembly into the front door outside handle frame, then slide the front door outside handle assembly toward the front of the vehicle to install it.


c.

w/ Smart Entry and Start System:

i.
B288532

Connect the connector.


ii.

Engage the 2 claws.



Hide 69217F 23.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B280354

Engage the 2 guides and claw, and install the front door outside handle cover to the lock cylinder assembly as shown in the illustration.


Hide 69217F 24.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B280355

Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B280630

Install the hole plug.


Hide 25.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B280352

Using a T30 "TORX" socket wrench, install the front door outside handle cover with lock cylinder assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B280351

Install the hole plug.


Hide 67404F 26.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B288545

Engage the guide as shown in the illustration.


b.

Install the front door rear lower frame sub-assembly with the 2 bolts.


Hide 67402F 27.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B280348

Engage the guide as shown in the illustration.


b.

Install the front door front lower frame sub-assembly with the 2 bolts.


Hide 68151C 28.INSTALL FRONT DOOR GLASS RUN

a.
B281735

Install the front door glass run.


Hide 67924 29.INSTALL NO. 2 FRONT DOOR STIFFENER CUSHION

a.

Clean the front door panel sub-assembly.


b.
B281687C04
2.281,1.333 1.49,1.438 false 1.302,1.344 1.76,1.677 0.458,0.333 10 false *1
*1 Double-sided Tape


Engage the 2 guides.


c.

Install a new No. 2 front door stiffener cushion with the 2 bolts.


Hide 85720D 30.INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the power window regulator motor.


a.
B280344

Using a T25 "TORX" socket wrench, install the front power window regulator motor assembly with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



Hide 31.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.

Install the temporary bolt to the front door window regulator assembly.


c.
B281734C06
1.906,0.823 1.156,0.156 false 1.281,1.146 0.333,1.438 false 1.771,1.115 1.917,1.958 false 2.271,1.292 2.229,1.917 false 2.5,0.969 2.906,1.135 false 0.969,0.063 1.26,0.302 0.292,0.24 10 false *1 2.167,1.906 2.542,2.177 0.375,0.271 10 false (1) 2.917,1.031 3.354,1.344 0.438,0.313 10 false (2) 2.438,1.292 2.854,1.604 0.417,0.313 10 false (3) 0.771,0.063 1.042,0.344 0.271,0.281 10 false (4) 0.146,1.344 0.51,1.625 0.365,0.281 10 false (5) 1.854,1.948 2.177,2.177 0.323,0.229 10 false (6)
*1 Temporary Bolt


Temporarily install the front door window regulator assembly.


d.

Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68102 32.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

Connect the cable to the negative (-) battery terminal.


b.

Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


c.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Disconnect the power window regulator master switch assembly.


e.
B288546E01
1.375,0.094 1.781,0.406 0.406,0.313 10 false (1) 0.625,0.156 0.958,0.417 0.333,0.26 10 false (2)

Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows and in the order shown in the illustration.


f.
B288542

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.
B281733

Install the grommet.


Hide 67832 33.INSTALL FRONT DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the front door panel.


b.
B310449C01
0.875,0.229 1.271,0.229 false 2.302,0.229 1.958,0.229 false 2.438,3.104 2.896,2.948 false 1.323,0.135 1.719,0.469 0.396,0.333 10 false *1 1.771,0.135 2.323,0.396 0.552,0.26 10 false *1 2.271,3.031 2.698,3.292 0.427,0.26 10 false *1
*1 Reference Point


Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.


c.

Attach the front door service hole cover according to the reference points on the front door panel.

NOTICE:

Securely install the front door service hole cover preventing wrinkles and air bubbles.



d.

Engage the 3 clamps.


e.

Connect each connector.


Hide 89430 34.INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)

Hide 35.INSTALL MIRROR SUB-ASSEMBLY WITH COVER

Hide 86160 36.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 84927 37.INSTALL SEAT MEMORY SWITCH (w/ Memory)

Hide 68172A 38.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP

a.
B288547

Install the front door inner glass weatherstrip.


Hide 69206B 39.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B277194

Engage the 2 claws and guide, and install the front door inside handle sub-assembly to the front door trim board sub-assembly.


Hide 67602 40.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B277193C06
2.927,0.875 2.438,1.031 false 2.302,1.646 2.385,1.281 false 2.958,0.75 3.375,1.052 0.417,0.302 10 false *1 2.208,1.656 2.615,1.927 0.406,0.271 10 false *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly


Connect the front door lock remote control cable assembly and front door inside locking cable assembly.


b.

Connect the connector.


c.
B288553C04
0.896,4.219 0.604,4.135 false 0.417,4.042 0.698,4.333 0.281,0.292 10 false *1
*1 Reference Boss


Engage the front door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.


d.
B288551

Engage the 10 clips.


e.

Install the 3 screws to install the front door trim board sub-assembly.


f.

If protective tape has been applied, remove it.


Hide 81230 41.INSTALL COURTESY LIGHT ASSEMBLY

Hide 74220 42.INSTALL FRONT ARMREST ASSEMBLY

a.
B277188

Engage the 2 guides, 3 clips and 7 claws, and install the front armrest assembly.


Hide 43.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.

Connect each connector.


b.
B277184

Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator master switch assembly with front door armrest base panel.


Hide 44.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.

Connect the connector.


b.
B288555

Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.


Hide 67492A 45.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B288549

Engage the 3 clips to install the front door lower frame bracket garnish.


Hide 69284C 46.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B288540

Engage the 3 claws to install the front door inside handle bezel plug.


Hide 47.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 48.INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)

Hide 50.INSPECT POWER SEAT OPERATION (w/ Memory)