Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM2030EQ _59 Vehicle Exterior _014677 DOOR / HATCH _0074692 REAR DOOR N

DOOR / HATCH  REAR DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B280381
0.698,0.146 1.083,0.396 0.385,0.25 10 false *1 2.51,0.146 2.833,0.396 0.323,0.25 10 false *2
*1 Centering Bolt
*2 Standard Bolt


CAUTION:

Before adjusting the door positions of vehicles equipped with side and curtain shield airbags, be sure to disconnect the battery. After adjustment, check that the SRS warning light is operating normally and there are no SRS DTCs output.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

Specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSPECT REAR DOOR

a.

Check that the clearance measurements of areas *a through *r are within each standard range.

B281697
1.396,0.917 1.771,1.167 0.375,0.25 10 false *a 1.385,1.781 1.76,2.052 0.375,0.271 10 false *b 2.75,0.938 3.115,1.167 0.365,0.229 10 false *c 2.74,1.792 3.198,2.104 0.458,0.313 10 false *d 4,0.979 4.406,1.281 0.406,0.302 10 false *e 4.208,1.844 4.625,2.146 0.417,0.302 10 false *f 5.906,1.479 6.26,1.802 0.354,0.323 10 false *g 6.083,2.323 6.271,2.49 0.188,0.167 10 false *h 6.771,3.375 7.125,3.646 0.354,0.271 10 false *i 6.583,3.823 6.927,4.104 0.344,0.281 10 false *j 6.719,5.302 7.031,5.573 0.313,0.271 10 false *k 6.281,4.74 6.719,5.021 0.438,0.281 10 false *l 4.24,5.5 4.677,5.875 0.438,0.375 10 false *m 2.448,5.677 2.792,5.938 0.344,0.26 10 false *n 2.854,5.375 3.198,5.667 0.344,0.292 10 false *o 0.729,4.844 1.021,5.135 0.292,0.292 10 false *p 1.135,4.552 1.479,4.813 0.344,0.26 10 false *q 0.708,3.281 1.125,3.625 0.417,0.344 10 false *r

Standard Clearance
Area Measurement Area Measurement
*a 3.5 to 6.5 mm (0.138 to 0.256 in.) *b 0.6 to 3.6 mm (0.0236 to 0.142 in.)
*c 3.5 to 6.5 mm (0.138 to 0.256 in.) *d 0.9 to 3.9 mm (0.0354 to 0.154 in.)
*e 3.5 to 6.5 mm (0.138 to 0.256 in.) *f 1.5 to 4.5 mm (0.0591 to 0.177 in.)
*g 3.5 to 6.5 mm (0.138 to 0.256 in.) *h 5.4 to 8.4 mm (0.213 to 0.331 in.)
*i -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) *j 2.3 to 5.3 mm (0.0906 to 0.209 in.)
*k 2.3 to 5.3 mm (0.0906 to 0.209 in.) *l -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
*m 3.2 to 7.4 mm (0.126 to 0.291 in.) *n 2.4 to 5.3 mm (0.0945 to 0.209 in.)
*o -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) *p 2.4 to 5.3 mm (0.0945 to 0.209 in.)
*q -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) *r 2.4 to 5.3 mm (0.0945 to 0.209 in.)


Hide 2.ADJUST REAR DOOR

NOTICE:

Make sure that the turn the ignition switch off when adjusting door lock strikers.


a.

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  

B334514


b.

Tighten the hinge bolts on the vehicle body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B280549

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


f.

Using a brass bar and a hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)