Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM2030EQ _59 Vehicle Exterior _014677 DOOR / HATCH _0074692 REAR DOOR A

DOOR / HATCH  REAR DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284D 3.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B280387

Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.


Hide 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

a.
B280389

Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.


b.

Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.


Hide 74260 5.REMOVE REAR ARMREST ASSEMBLY

a.
B280391

Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.


Hide 67604 6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B280590C06
1.458,0.583 1.083,0.51 false 0.906,0.406 1.333,0.625 0.427,0.219 10 false *1
*1 Protective Tape


Put protective tape around the rear door panel.


b.
B280393

Remove the 3 screws.


c.

Using a clip remover, disengage the 8 clips.


d.

Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

B334513C05
4.208,0.875 4.917,0.875 false 0.927,2.083 1.073,1.938 false 0.76,2 1.094,2.188 0.333,0.188 10 *1 4.031,0.781 4.385,0.969 0.354,0.188 10 *2
*1 Reference Boss *2 Rear Door Inner Glass Weatherstrip



e.

Disengage the reference boss from the rear door panel.


f.

Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.


g.
B280396

Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.


h.

Disconnect the connector.


i.
B280399C06
1.333,2.448 1.177,2.688 false 1.333,2.302 1.667,2.563 0.333,0.26 10 false *1
*1 Screwdriver


Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.


Hide 69206C 7.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B277194

Disengage the 2 claws and guide, and remove the rear door inside handle sub-assembly.


Hide 68174A 8.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

a.
B280398C06
1.875,0.719 2.198,0.823 false 0.531,0.969 0.375,1.125 false 1.708,0.625 2.052,0.896 0.344,0.271 10 false *1 0.208,1.094 0.531,1.323 0.323,0.229 10 false *1
*1 Screwdriver


Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.


Hide 67842E 9.REMOVE REAR DOOR SERVICE HOLE COVER

a.
B281690

Disconnect the connector and remove the rear door service hole cover.

HINT:

Remove any remaining butyl tape from the door.



Hide 68640A 10.REMOVE REAR DOOR CHECK ASSEMBLY

a.
B280406

Remove the bolt and 2 nuts and rear door check assembly.


Hide 67872 11.REMOVE REAR DOOR WEATHERSTRIP

a.
B281691

Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.


Hide 68152C 12.REMOVE REAR DOOR GLASS RUN

a.
B280408

Remove the rear door glass run.


Hide 67408F 13.REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

a.
B280409

Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.

NOTICE:

When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.



Hide 68124B 14.REMOVE REAR DOOR QUARTER WINDOW GLASS

a.
B280410

Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.


b.

Remove the rear door quarter window glass from the rear door quarter window weatherstrip.


Hide 68104 15.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

a.
B281692

Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

NOTICE:

Do not damage the door glass.



Hide 69906B 16.REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY

a.
B280414C05
0.969,0.917 0.854,0.917 0.854,0.917 0.656,1.552 false 0.99,0.813 1.323,1.021 0.333,0.208 10 false *1
*1 Protective Tape


Using a screwdriver, remove the rear door glass channel sub-assembly.

HINT:

Tape the screwdriver tip before use.



Hide 69975A 17.REMOVE REAR DOOR GLASS CHANNEL FILLER

a.

Remove the rear door glass channel filler.


Hide 67674A 18.REMOVE REAR DOOR FRAME GARNISH

a.
B280403

Disengage the clip and remove the rear door frame garnish.

HINT:

This garnish needs to be replaced with a new one because the clip will break when removing it.



Hide 19.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY

a.
B280418C10
1.25,0.615 1.823,0.5 false 1.094,0.542 1.396,0.802 0.302,0.26 10 false *1
*1 Temporary Bolt


Disconnect the connector.


b.

Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.



c.

Remove the 3 bolts.


d.

Remove the rear door window regulator assembly.


e.

Remove the temporary bolt from the rear door window regulator assembly.


Hide 85720E 20.REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B280419

Using a T25 "TORX" socket wrench, remove the 3 screws and rear power window regulator motor assembly.


Hide 69060A 21.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

a.
B280420C08
3.135,2.865 2.979,2.823 false 3.167,2.792 3.427,3.042 0.26,0.25 10 false *1
*1 Release Plate


Using a T30 "TORX" socket wrench, remove the 3 screws.


b.

Move the rear door lock with motor assembly downward and pull the release plate out of the rear door outside handle frame.


c.

When reusing the rear door lock with motor assembly:

i.
B280422

Remove the door lock wiring harness seal from the rear door lock with motor assembly.



Hide 69740D 22.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B280423

Using a screwdriver, disengage the claw.


b.
B280425

Remove the rear door lock remote control cable assembly.


Hide 69780B 23.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B280427

Using a screwdriver, disengage the 3 claws.


b.
B280429

Remove the rear door inside locking cable assembly.


Hide 69250G 24.REMOVE REAR DOOR OUTSIDE HANDLE COVER ASSEMBLY

a.
B280431

Using a T30 "TORX" socket wrench, loosen the screw.

HINT:

The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.



b.

Disengage the claw and remove the rear door outside handle cover assembly.


Hide 69240 25.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B280432

Pull and hold the release plate of the rear door outside handle frame sub-assembly as shown in the illustration.

NOTICE:

The release plate may interfere with the rear door outside handle assembly and may be damaged when removing the rear door outside handle assembly, unless the release plate of the rear door outside handle frame sub-assembly is pulled and held.



b.
B280433

Remove the rear door outside handle assembly as shown in the illustration.


Hide 69241G 26.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B280435

Disengage the 3 claws and remove the rear door front outside handle pad.


Hide 69242G 27.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B280436

Disengage the 2 claws and remove the rear door rear outside handle pad.


Hide 69204A 28.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B280437C06
0.396,1.771 0.698,1.688 false 0.188,1.677 0.49,1.958 0.302,0.281 10 false *1 0.115,0.104 0.479,0.396 0.365,0.292 10 false *a 0.135,1.958 0.417,2.198 0.281,0.24 10 false *b
*1 Door Handle Nut
*a Outside
*b Inside


Using a T30 "TORX" socket wrench, remove the screw and door handle nut.


b.

Slide the rear door outside handle frame sub-assembly to disengage the claw of the rear door outside handle frame sub-assembly, and then remove it.


Hide 67888F 29.REMOVE REAR DOOR NO. 2 WEATHERSTRIP

a.
B281741

Using a clip remover, disengage the 5 clips and remove the rear door No. 2 weatherstrip.


Hide 67003C 30.REMOVE REAR DOOR PANEL CUSHION

a.
B281693

Disengage the 2 claws and remove the 2 rear door panel cushions.


Hide 75740 31.REMOVE REAR DOOR BELT MOULDING ASSEMBLY

Hide 75762A 32.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

Hide 75764A 33.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING

Hide 75988C 34.REMOVE REAR DOOR OUTSIDE STRIPE

Hide 75978H 35.REMOVE REAR DOOR LOWER OUTSIDE STRIPE