Use the same procedure for both the RH and LH sides.
The procedure described below is for the LH side.
1. REPAIR INSTRUCTION
75978H
2.INSTALL REAR DOOR LOWER OUTSIDE STRIPE
75988C
3.INSTALL REAR DOOR OUTSIDE STRIPE
75764A
4.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING
75762A
5.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING
75740
6.INSTALL REAR DOOR BELT MOULDING ASSEMBLY
67003C
7.INSTALL REAR DOOR PANEL CUSHION
Engage the 2 claws to install 2 new rear door panel cushions.
67888F
8.INSTALL REAR DOOR NO. 2 WEATHERSTRIP
Engage the 5 clips to install the rear door No. 2 weatherstrip.
69204A
9.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.
| *1 | Door Handle Nut |
| *a | Outside |
| *b | Inside |
Engage the claw.
Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw and door handle nut.
69242G
10.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD
Engage the 2 claws to install the rear door rear outside handle pad.
69241G
11.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD
Engage the 3 claws to install the rear door front outside handle pad.
69240
12.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY
Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.
If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.
Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.
69250G
13.INSTALL REAR DOOR OUTSIDE HANDLE COVER ASSEMBLY
Engage the claw and install the rear door outside handle cover assembly.
Using a T30 "TORX" socket wrench, install the rear door outside handle cover assembly with the screw.
69780B
14.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY
Install the rear door inside locking cable assembly.
Engage the 3 claws.
69740D
15.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
Install the rear door lock remote control cable assembly.
Engage the claw.
69060A
16.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY
When reusing the removed rear door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.
Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door with motor lock assembly.
Apply MP grease to the sliding parts of the rear door lock with motor assembly.
When reusing the rear door with motor lock assembly:
Install a new door lock wiring harness seal to the rear door lock with motor assembly.
| *1 | Release Plate |
Insert the rear door lock with motor assembly to the rear door outside handle release plate, and set it to the rear door panel.
Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock with motor assembly.
Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.
85720E
17.INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY
The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.
Using a T25 "TORX" socket wrench, install the rear power window regulator motor assembly with the 3 screws.
When replacing the rear window regulator, a new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
18.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY
Apply MP grease to the sliding parts of the rear door window regulator assembly.
Install the temporary bolt to the rear door window regulator assembly.
| *1 | Temporary Bolt |
Temporarily install the rear door window regulator assembly.
Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.
Tighten the bolts in the order shown in the illustration.
67674A
19.INSTALL REAR DOOR FRAME GARNISH
Engage the clip to install a new rear door frame garnish.
69975A
20.INSTALL REAR DOOR GLASS CHANNEL FILLER
Apply soapy water to a new rear door glass channel filler.
| *A | Front Side |
| *B | Rear Side |
| *a | 4.57 mm (0.180 in.) |
| *b | 4.8 mm (0.189 in.) |
| *c | Edge of curved surface |
Install the rear door glass channel filler to the position shown in the illustration.
69906B
21.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY
Apply soapy water to the channel filler side of the rear door glass channel sub-assembly.
| *A | Front Side |
| *B | Rear Side |
| *a | 4.57 mm (0.180 in.) |
| *b | 4.8 mm (0.189 in.) |
| *c | Edge of curved surface |
Using a plastic hammer, install the rear door glass channel sub-assembly to the position shown in the illustration.
To prevent damaging the rear door glass sub-assembly, be careful not to strike the channel with too much force.
68104
22.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Slide the rear door glass sub-assembly to install it as shown in the illustration.
68124B
23.INSTALL REAR DOOR QUARTER WINDOW GLASS
Install the rear door quarter window glass to the rear door quarter window weatherstrip.
Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.
67408F
24.INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY
Install the rear door lower window frame sub-assembly with the screw and 2 bolts.
68152C
25.INSTALL REAR DOOR GLASS RUN
Install the rear door glass run.
67872
26.INSTALL REAR DOOR WEATHERSTRIP
Engage the 20 clips to install the rear door weatherstrip.
68640A
27.INSTALL REAR DOOR CHECK ASSEMBLY
Apply MP grease to the sliding parts of the rear door check assembly.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the rear door check assembly with the 2 nuts and bolt.
67842E
28.INSTALL REAR DOOR SERVICE HOLE COVER
Apply new butyl tape to the rear door panel.
| *1 | Reference Point |
Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.
Attach the rear door service hole cover according to the reference points on the rear door panel.
Securely install the rear door service hole cover preventing wrinkles and air bubbles.
Connect the connector.
68174A
29.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP
Install the rear door inner glass weatherstrip.
69206C
30.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the guide and 2 claws to install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.
67604
31.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
Install the No. 1 door scuff plate clamp as shown in the illustration.
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.
Connect the connector.
Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
| *1 | Reference Boss | - | - |
Engage the 8 clips and install the rear door trim board sub-assembly.
Install the 3 screws.
If protective tape has been applied, remove it.
74260
32.INSTALL REAR ARMREST ASSEMBLY
Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.
33.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Connect the connector.
Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.
69284D
34.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG
Engage the 3 claws to install the rear door inside handle bezel plug.
35.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
36.INSPECT POWER WINDOW OPERATION