Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM2030EQ _59 Vehicle Exterior _014678 MIRROR (EXT) _0074700 POWER MIRROR CONTROL SYSTEM(w/ Memory) U

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH


B209687
4.083,0.24 4.406,0.448 0.323,0.208 3.021,0.24 3.344,0.448 0.323,0.208 4.135,0.271 4.667,0.615 0.531,0.344 10 false J13 3.104,0.271 3.458,0.521 0.354,0.25 10 false z6

a.

Disconnect the J13 connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
J13-14 (BDR) - Body ground GR*1 - Body ground
W*2 - Body ground
+B power supply Always 11 to 14 V
J13-6 (CPUB) - Body ground W - Body ground +B power supply Always 11 to 14 V
J13-5 (SIG) - Body ground BE - Body ground Ignition power supply Engine switch off → on (IG) 0 V → 11 to 14 V
J13-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the J13 connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
z6-1 (RMVR) - z6-9 (RMHR) - Vertical mirror motor drive voltage RH mirror surface moving upward → stopped 11 to 14 V → 0 V
z6-10 (RM+R) - z6-1 (RMVR) - Vertical mirror motor drive voltage RH mirror surface moving downward → stopped 11 to 14 V → 0 V
z6-10 (RM+R) - z6-9 (RMHR) - Horizontal mirror motor drive voltage RH mirror surface moving right → stopped 11 to 14 V → 0 V
z6-9 (RMHR) - z6-1 (RMVR) - Horizontal mirror motor drive voltage RH mirror surface moving left → stopped 11 to 14 V → 0 V
z6-5 (RVC) - z6-14 (RE1) - Mirror position sensor power supply Engine switch on (IG) 4.55 to 5.45 V
z6-6 (VSSR) - z6-14 (RE1) - Mirror position sensor signal Engine switch on (IG) 0.96 to 4.04 V
z6-13 (HSSR) - z6-14 (RE1) - Mirror position sensor signal Engine switch on (IG) 0.96 to 4.04 V
J13-3 (M2) - J13-13 (MSWE)*2 B - V M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
J13-2 (M1) - J13-13 (MSWE)*2 G - V M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
J13-1 (MM) - J13-13 (MSWE)*2 P - V SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V

*1: for LHD

*2: for RHD




CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH


B209687
2.979,0.25 3.302,0.458 0.323,0.208 4.094,0.25 4.417,0.458 0.323,0.208 3.073,0.271 3.375,0.552 0.302,0.281 10 false z5 4.135,0.271 4.5,0.563 0.365,0.292 10 false K12

a.

Disconnect the K12 connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
K12-14 (BDR) - Body ground W*1 - Body ground
GR*2 - Body ground
+B power supply Always 11 to 14 V
K12-6 (CPUB) - Body ground W - Body ground +B power supply Always 11 to 14 V
K12-5 (SIG) - Body ground GR - Body ground Ignition power supply Engine switch off → on (IG) 0 V → 11 to 14 V
K12-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the K12 connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
z5-1 (LMVR) - z5-9 (LMHR) - Vertical mirror motor drive voltage LH mirror surface moving upward → stopped 11 to 14 V → 0 V
z5-10 (LM+R) - z5-1 (LMVR) - Vertical mirror motor drive voltage LH mirror surface moving downward → stopped 11 to 14 V → 0 V
z5-10 (LM+R) - z5-9 (LMHR) - Horizontal mirror motor drive voltage LH mirror surface moving right → stopped 11 to 14 V → 0 V
z5-9 (LMHR) - z5-1 (LMVR) - Horizontal mirror motor drive voltage LH mirror surface moving left → stopped 11 to 14 V → 0 V
z5-5 (LVC) - z5-14 (LE1) - Mirror position sensor power supply Engine switch on (IG) 4.55 to 5.45 V
z5-6 (VSSR) - z5-14 (LE1) - Mirror position sensor signal Engine switch on (IG) 0.96 to 4.04 V
z5-13 (HSSR) - z5-14 (LE1) - Mirror position sensor signal Engine switch on (IG) 0.96 to 4.04 V
K12-3 (M2) - K12-13 (MSWE)*1 G - B M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
K12-2 (M1) - K12-13 (MSWE)*1 R - B M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
K12-1 (MM) - K12-13 (MSWE)*1 P - B SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V

*1: for LHD

*2: for RHD