CHECK WINDSHIELD WIPER RELAY ASSEMBLY
Disconnect the I72 windshield wiper relay assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I72-2 (IG) - Body ground | L - Body ground | Ignition switch ON signal (Power source circuit) | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| I72-8 (VR2) - I72-21 (VR1) | B - W | Adjusting volume circuit | Windshield wiper switch adjusting ring* changed | 0 to 220 Ω |
| I72-12 (E) - Body ground | W-B - Body ground | Body ground | Always | Below 1 Ω |
| I72-16 (WIG) - Body ground | Y - Body ground | Signal power source circuit | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| I72-25 (W) - Body ground | GR - Body ground | Front washer switch circuit | Front washer switch on | Below 1 Ω |
| Front washer switch off | 10 kΩ or higher |
*: The rain sensor sensitivity can be adjusted by the windshield wiper switch adjusting ring.
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the I72 windshield wiper relay assembly connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I72-1 (+SM) - Body ground | B - Body ground | Front wiper motor position detection signal | Front wiper motor in low or high operation | Below 1 V ←→ 11 to 14 V |
| Front wiper motor off | Below 1 V | |||
| I72-3 (C1) - I72-5 (CO) | P - R | Front wiper switch AUTO signal circuit | Ignition switch ON, front wiper switch in AUTO | Below 1 V |
| Ignition switch ON, front wiper switch off | 11 to 14 V | |||
| I72-10 (+1) - Body ground | B - Body ground | Front wiper motor low speed signal circuit | Front wiper motor in low operation | 11 to 14 V |
| Front wiper motor off | Below 1 V | |||
| I72-11 (+2) - Body ground | V - Body ground | Front wiper motor high speed signal circuit | Front wiper motor in high operation | 11 to 14 V |
| Front wiper motor off | Below 1 V | |||
| I72-14 (MPX1) - Body ground | G - Body ground | Rain sensor signal | Ignition switch ON | Pulse generation |
| I72-24 (SPD) - Body ground | V - Body ground | Speed signal | Ignition switch ON, wheel being rotated | Pulse generation
(See Waveform 1) |
| I72-25 (W) - Body ground | GR - Body ground | Front washer switch circuit | Front washer switch on | Below 1 V |
| Front washer switch off | 11 to 14 V |
If the result is not as specified, the windshield wiper relay assembly may have a malfunction.
Waveform 1 (Reference):
| Item | Condition |
|---|---|
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle condition | Wheel being rotated |
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
CHECK HEADLIGHT CLEANER CONTROL RELAY
Disconnect the A52 headlight cleaner control relay connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A52-1 (HDLO) - A52-4 (E) | GR - W-B | Low beam headlight signal | Light control switch in head position | Below 1 V |
| Light control switch off | 11 to 14 V | |||
| A52-2 (H) - A52-4 (E) | SB - W-B | Headlight cleaner switch operation signal | Ignition switch ON, light control switch in on position and headlight cleaner switch off | 11 to 14 V |
| Ignition switch ON, light control switch in on position and headlight cleaner switch on | Below 1 V | |||
| A52-3 (IG) - A52-4 (E) | R - W-B | Ignition switch ON signal (Power source circuit) | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | |||
| A52-4 (E) - Body ground | W-B - Body ground | Body ground | Always | Below 1 Ω |
| A52-5 (FRWA) - A52-4 (E) | G - W-B | Front washer switch signal | Ignition switch ON and front washer switch off | 11 to 14 V |
| Ignition switch ON and front washer switch on | Below 1 V |
If the result is not as specified, there may be a malfunction in the wire harness.