Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM2030EQ _59 Vehicle Exterior _014679 WIPER / WASHER _0074707 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Wiper ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to the windshield wiper relay assembly.

WIRING DIAGRAM

E196302E06
4.896,2.552 5.24,2.74 0.344,0.188 10 false I72 4.896,2.74 7.063,2.927 2.167,0.188 10 false Windshield Wiper Relay Assembly 0.594,0.927 2.01,1.115 1.417,0.188 10 false from IG1 NO. 1 Relay 5.448,0.917 5.75,1.115 0.302,0.198 10 false IG 5.448,2.146 5.667,2.344 0.219,0.198 10 false E 5.198,2.063 5.375,2.208 0.177,0.146 10 false 12 5.271,0.813 5.396,0.99 0.125,0.177 10 false 2 3.594,1.052 4.146,1.25 0.552,0.198 10 false WIPER 0.594,1.5 2.021,1.688 1.427,0.188 10 false from IG1 NO. 2 Relay 3.365,1.677 4.438,1.875 1.073,0.198 10 false ECU-IG1 NO. 2 5.469,1.521 5.792,1.719 0.323,0.198 10 false WIG 5.198,1.438 5.375,1.583 0.177,0.146 10 false 16

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BATTERY AND BODY GROUND)
a.
E144475C05
1.5,1.042 2.01,1.344 0.51,0.302 2.74,2.208 3.021,2.667 false 1.146,2.469 1.146,2.938 false 0.667,2.823 0.927,2.219 false 1.646,1.104 2.198,1.469 0.552,0.365 10 false I72 0.167,0.167 0.573,0.49 0.406,0.323 10 false *a 3.031,2.688 3.427,3 0.396,0.313 10 false E 1.031,2.948 1.573,3.177 0.542,0.229 10 false WIG 0.563,2.833 0.948,3.135 0.385,0.302 10 false IG
*a Front view of wire harness connector
(to Windshield Wiper Relay Assembly)


Disconnect the I72 windshield wiper relay assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I72-2 (IG) - Body ground Ignition switch ON 11 to 14 V
I72-16 (WIG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I72-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR