Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM2030EQ _59 Vehicle Exterior _014679 WIPER / WASHER _0074708 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Connect the connector.


c.

Turn the ignition switch to ON.


d.

Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.


e.

Turn the ignition switch off.


f.

Disconnect the connector.


g.
E226241
1.479,1.302 1.292,1.302 false 1.115,1.188 1.365,1.417 0.25,0.229 10 *a
*a Pivot of the windshield wiper motor assembly


Apply MP grease to the pivot of the windshield wiper motor assembly.


h.
E226239
1.344,0.865 0.594,0.865 false 1.99,1.323 2.802,1.323 false 2.823,1.208 3.094,1.469 0.271,0.26 10 *1 0.427,0.76 0.719,1.021 0.292,0.26 10 *a
*1 No. 1 Rod
*a Pivot of the windshield wiper motor assembly


Connect the No. 1 rod to the pivot of the windshield wiper motor assembly.


Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for LHD)

a.
E234311
0.771,2.625 1.615,2.771 false 1.646,2.677 1.969,2.958 0.323,0.281 10 false *1
*1 Motor Grommet


Engage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.



b.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.

Connect the connector.


Hide 3.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)

a.
E234312
0.875,2.615 1.583,2.781 false 1.625,2.708 2,2.969 0.375,0.26 10 false *1
*1 Motor Grommet


Engage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.



b.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.

Connect the connector and then engage the 2 clamps.


Hide 55781E 4.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Engage the 8 guides as shown in the illustration.

E246629


b.

Engage the 6 claws and guide to install the cowl top ventilator louver sub-assembly.

E246631


Hide 53867H 5.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

a.
E226231

Engage the 3 guides and 2 clips to install the front fender to cowl side seal LH as shown in the illustration.


Hide 53866J 6.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure as for the LH side.


Hide 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E226523
1.052,1.125 0.229,1.125 false 0.073,1.031 0.427,1.281 0.354,0.25 10 *a
*a Wiper Arm Serration


When reusing the front wiper arm and blade assembly LH:

i.

Clean the wiper arm serrations.



b.
E231343
1.958,1.104 2.26,1.104 false 2.292,0.99 2.604,1.229 0.313,0.24 10 *a
*a Wiper Pivot Serration


When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.
E226090
1.25,1.052 1.25,1.583 false 0.729,1.208 1.021,1.49 0.292,0.281 10 A 0.719,0.75 1.094,1.073 0.375,0.323 10 A 1.167,1.594 1.51,1.833 0.344,0.24 10 *1
*1 Ceramic Dot


Set the front wiper arm and blade assembly LH in the range shown in the illustration and then install the front wiper arm and blade assembly LH with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

Area Measurement
A 7.5 mm (0.295 in.)

HINT:

Hold the wiper arm by hand while tightening the nut.



Hide 8.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
E226523
1.052,1.125 0.229,1.125 false 0.073,1.031 0.427,1.281 0.354,0.25 10 *a
*a Wiper Arm Serration


When reusing the front wiper arm and blade assembly RH:

i.

Clean the wiper arm serrations.



b.
E231343
1.958,1.104 2.26,1.104 false 2.292,0.99 2.604,1.229 0.313,0.24 10 *a
*a Wiper Pivot Serration


When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.
E226089
1.031,0.844 1.031,1.104 false 0.531,0.396 0.896,0.708 0.365,0.313 10 false A 0.542,0.865 0.948,1.156 0.406,0.292 10 false A 0.958,1.104 1.365,1.396 0.406,0.292 10 false *1
*1 Ceramic Dot


Set the front wiper arm and blade assembly RH in the range shown in the illustration and then install the front wiper arm and blade assembly RH with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

Area Measurement
A 7.5 mm (0.295 in.)

HINT:

Hold the wiper arm by hand while tightening the nut.



d.

Turn the ignition switch to ON.


e.

Operate the front wiper while spraying washer fluid onto the windshield glass. Make sure that the front wiper functions properly and the wiper does not come into contact with the vehicle body.


f.

Lift each wiper arm twice after the wipers stop and check the wiper set position.


g.

Turn the ignition switch off.