Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH
RM2030EQ _59 Vehicle Exterior _014679 WIPER / WASHER _0074710 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85110 1.INSPECT FRONT WIPER INTERMITTENT OPERATION (W/O AUTO WIPER SYSTEM)

a.
E171721
0.177,1.146 0.635,1.417 0.458,0.271 2.813,1.146 3.271,1.417 0.458,0.271 1.167,1.094 0.896,0.667 false 2.448,1.448 2.542,1.875 false 0.073,0.031 0.438,0.344 0.365,0.313 10 false *a 0.323,1.177 0.729,1.427 0.406,0.25 10 false I32 0.76,0.49 1.198,0.802 0.438,0.313 10 false +1 2.958,1.177 3.313,1.417 0.354,0.24 10 false I31 2.458,1.875 2.854,2.156 0.396,0.281 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


for LHD:

i.

Connect a voltmeter positive (+) lead to terminal I32-3 (+1) and a negative (-) lead to terminal I31-4 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the wiper switch to the INT position.


iv.

Operate the intermittent wiper relay and check the voltage between terminals I32-3 (+1) and I31-4 (EW).

OK:

Voltage changes as shown in the illustration.


E136493
2.625,0.104 3.229,0.385 0.604,0.281 10 false FAST: 1.927,0.385 2.646,0.646 0.719,0.26 10 false 11 to 14 V 2.344,0.875 2.708,1.135 0.365,0.26 10 false 0 V 3.177,1.385 3.646,1.667 0.469,0.281 10 false Start 0.073,0.5 1.729,1.167 1.656,0.667 10 false Voltage between terminals I32-3 (+1) and I31-4 (EW): 0.771,1.375 2,1.719 1.229,0.344 10 false Wiper Operation: 3.354,1 4.646,1.26 1.292,0.26 10 false 1.6 +/- 1 seconds 5.792,1 7.115,1.302 1.323,0.302 10 false 10.7 +/- 5 seconds 2.729,1.385 3.167,1.667 0.438,0.281 10 false Stop 5.583,1.385 6.083,1.656 0.5,0.271 10 false Start 4.792,1.385 5.25,1.677 0.458,0.292 10 false Stop 4.427,0.104 5.167,0.438 0.74,0.333 10 false SLOW:

If the result is not as specified, replace the windshield wiper switch assembly.



b.
E226489
0.177,1.115 0.635,1.385 0.458,0.271 2.813,1.115 3.271,1.385 0.458,0.271 0.865,1.844 0.948,1.469 false 2.271,1.094 2.802,0.719 false 0.125,0.052 0.583,0.333 0.458,0.281 10 false *a 0.313,1.156 0.74,1.438 0.427,0.281 10 false I31 2.938,1.146 3.313,1.396 0.375,0.25 10 false I32 2.854,0.615 3.24,0.885 0.385,0.271 10 false +1 0.719,1.844 1.25,2.073 0.531,0.229 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


for RHD:

i.

Connect a voltmeter positive (+) lead to terminal I32-2 (+1) and a negative (-) lead to terminal I31-7 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the wiper switch to the INT position.


iv.

Operate the intermittent wiper relay and check the voltage between terminals I32-2 (+1) and I31-7 (EW).

OK:

Voltage changes as shown in the illustration.


E136493
2.625,0.104 3.104,0.271 0.479,0.167 10 false FAST: 1.927,0.385 2.615,0.563 0.688,0.177 10 false 11 to 14 V 2.344,0.885 2.594,1.063 0.25,0.177 10 false 0 V 3.177,1.385 3.531,1.563 0.354,0.177 10 false Start 0.073,0.5 1.719,1.177 1.646,0.677 10 false Voltage between terminals I32-3 (+1) and I31-7 (EW): 0.771,1.375 1.854,1.552 1.083,0.177 10 false Wiper Operation: 3.354,1 4.542,1.198 1.188,0.198 10 false 1.6 +/- 1 seconds 5.792,1 7.021,1.198 1.229,0.198 10 false 10.7 +/- 5 seconds 2.729,1.385 3.083,1.563 0.354,0.177 10 false Stop 5.583,1.385 5.938,1.563 0.354,0.177 10 false Start 4.792,1.385 5.146,1.563 0.354,0.177 10 false Stop 4.438,0.104 4.979,0.302 0.542,0.198 10 false SLOW:

If the result is not as specified, replace the windshield wiper switch assembly.



Hide 2.INSPECT FRONT WASHER OPERATION

a.
E171721
0.177,1.146 0.635,1.417 0.458,0.271 2.813,1.146 3.271,1.417 0.458,0.271 1.167,1.083 0.896,0.656 false 2.448,1.438 2.542,1.865 false 0.073,0.031 0.438,0.344 0.365,0.313 10 false *a 0.323,1.177 0.729,1.427 0.406,0.25 10 false I32 0.781,0.51 1.219,0.823 0.438,0.313 10 false +1 2.958,1.177 3.313,1.417 0.354,0.24 10 false I31 2.458,1.885 2.854,2.167 0.396,0.281 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


for LHD:

i.

Connect a voltmeter positive (+) lead to terminal I32-3 (+1) and a negative (-) lead to terminal I31-4 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the washer switch on and off, and check the voltage between terminals I32-3 (+1) and I31-4 (EW).

OK:

Voltage changes as shown in the illustration.


E226602
4.094,1.333 4.021,1.5 false 4.76,1.333 4.844,1.51 false 0.969,0.823 2.625,1.354 1.656,0.531 10 false Voltage between terminals I32-3 (+1) and I31-4 (EW): 1.677,0.208 2.667,0.542 0.99,0.333 10 false Washer Switch: 2.49,1.5 4.49,1.75 2,0.25 10 false Approximately 0.5 seconds 4.573,1.49 6.51,1.75 1.938,0.26 10 false Approximately 2.2 seconds 2.958,0.792 3.792,1.156 0.833,0.365 10 false 11 to 14 V 3.375,1.135 3.833,1.542 0.458,0.406 10 false 0 V 3.302,0.438 3.813,0.833 0.51,0.396 10 false OFF 3.344,0.219 3.74,0.552 0.396,0.333 10 false ON

If the result is not as specified, replace the windshield wiper switch assembly.



b.
E226489
0.177,1.115 0.635,1.385 0.458,0.271 2.813,1.115 3.271,1.385 0.458,0.271 0.865,1.844 0.948,1.469 false 2.271,1.094 2.802,0.719 false 0.125,0.052 0.313,0.229 0.188,0.177 10 false *a 0.292,1.167 0.594,1.344 0.302,0.177 10 false I31 2.917,1.156 3.198,1.323 0.281,0.167 10 false I32 2.854,0.615 3.156,0.823 0.302,0.208 10 false +1 0.729,1.844 1.156,2.094 0.427,0.25 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


for RHD:

i.

Connect a voltmeter positive (+) lead to terminal I32-2 (+1) and a negative (-) lead to terminal I31-7 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the washer switch on and off, and check the voltage between terminals I32-2 (+1) and I31-7 (EW).

OK:

Voltage changes as shown in the illustration.


E226602
4.094,1.333 4.021,1.5 false 4.76,1.333 4.844,1.51 false 0.969,0.823 2.625,1.375 1.656,0.552 10 false Voltage between terminals I32-3 (+1) and I31-7 (EW): 1.677,0.208 2.667,0.542 0.99,0.333 10 false Washer Switch: 2.49,1.5 4.49,1.75 2,0.25 10 false Approximately 0.5 seconds 4.573,1.49 6.51,1.75 1.938,0.26 10 false Approximately 2.2 seconds 2.958,0.792 3.792,1.156 0.833,0.365 10 false 11 to 14 V 3.375,1.135 3.833,1.542 0.458,0.406 10 false 0 V 3.302,0.438 3.813,0.833 0.51,0.396 10 false OFF 3.344,0.219 3.74,0.552 0.396,0.333 10 false ON

If the result is not as specified, replace the windshield wiper switch assembly.