Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY › 2012.02–2015.04
RM2030EQ _59 Vehicle Exterior _014680 LIGHTING (EXT) _0074720 HEADLIGHT ASSEMBLY A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL GROMMET

a.
E226742

Install the grommet.


Hide 81610F 2.INSTALL CLEARANCE LIGHT BULB (for LH Side)

a.

Install the clearance light bulb to the clearance light socket.


b.
E226733

Turn the clearance light socket with the clearance light bulb in the direction indicated by the arrow shown in the illustration and install them as a unit.


Hide 81610F 3.INSTALL CLEARANCE LIGHT BULB (for RH Side)

a.

for Long Type:

HINT:

Use the same procedure as for the LH side.



b.

for Short Type:

i.

Install the clearance light bulb to the clearance light socket.


ii.
E283674

Turn the clearance light socket with the clearance light bulb in the direction indicated by the arrow shown in the illustration and install them as a unit.



Hide 81730B 4.INSTALL FRONT TURN SIGNAL LIGHT BULB

a.

Install the front turn signal light bulb to the front turn signal light socket.


b.
E226731

Turn the front turn signal light socket with the front turn signal light bulb in the direction indicated by the arrow shown in the illustration and install them as a unit.


Hide 81144C 5.INSTALL HEADLIGHT SOCKET COVER

a.

for Halogen Headlight:

i.

Install the 2 headlight socket covers to the headlight unit.



b.

for HID Headlight:

i.

Install the headlight socket cover to the headlight unit.



Hide 81110D 6.INSTALL NO. 2 HEADLIGHT BULB (for Halogen Headlight)

a.
E226735

Turn the No. 2 headlight bulb in the direction indicated by the arrow shown in the illustration to install it.

NOTICE:

Do not touch the bulb glass.



Hide 81110L 7.INSTALL DISCHARGE HEADLIGHT BULB (for HID Headlight)

a.

Set the discharge headlight bulb to the headlight unit.

NOTICE:

Do not touch the bulb glass.



b.
E226729
1.469,0.052 1.677,0.229 0.208,0.177 10 true 2 1.906,0.104 2.115,0.281 0.208,0.177 10 true 2 0.958,1.073 1.167,1.25 0.208,0.177 10 true 1

Lock the set spring to install the discharge headlight bulb as shown in the illustration.


Hide 81108 8.INSTALL HEADLIGHT LIGHT CONTROL ECU SUB-ASSEMBLY (for HID Headlight)

a.
E226727
1.655,1.262 1.805,1.784 false 1.745,1.807 1.905,1.968 0.161,0.161 10 *1
*1 Red Line


Turn the socket of the headlight light control ECU sub-assembly in the direction indicated by the arrow shown in the illustration to connect it.

NOTICE:
·

Check that the O-ring is installed on the headlight light control ECU sub-assembly.

·

Check that the O-ring is not damaged or contaminated with foreign matter. If there is any damage, replace the O-ring with a new one.

·

Do not pull the headlight light control ECU sub-assembly with the socket connected.




b.

Check that the red line on the output harness is not twisted and store the harness in the headlight assembly securely so that the output harness is not pinched.


c.
E226725
3.148,0.424 3.3,0.576 0.152,0.152 10 *1 2.773,0.645 3.113,0.51 3.113,0.51 2.86,0.441 false
*1 Lock Mark


Turn the headlight light control ECU sub-assembly in the direction indicated by the arrow shown in the illustration until the lock marks are aligned to install it.

NOTICE:
·

To prevent incomplete installation, make sure to fully push in and turn the headlight light control ECU sub-assembly until the lock marks are aligned.

·

Do not apply excessive force using a tool.




Hide 81110B 9.INSTALL NO. 1 HEADLIGHT BULB

a.
E226723

Turn the No. 1 headlight bulb in the direction indicated by the arrow shown in the illustration to install it.

NOTICE:

Do not touch the bulb glass.