Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM2030EQ _59 Vehicle Exterior _014680 LIGHTING (EXT) _0074736 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects the ambient light. The sensor creates an electrical signal based on the amount of light, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1244 Light Sensor Circuit Malfunction
·

Malfunction in automatic light control sensor

·

Open or short in automatic light control sensor circuit


·

Automatic light control sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

E223761
0.604,2.627 0.866,2.778 0.262,0.152 10 I61 0.58,2.809 2.591,2.975 2.011,0.166 10 Automatic Light Control Sensor 4.927,2.785 6.815,3.129 1.887,0.344 10 Main Body ECU (Multiplex Network Body ECU) 4.927,2.627 5.202,2.797 0.274,0.17 10 I13 1.642,0.816 2.034,0.969 0.392,0.153 10 CLTB 1.642,2.16 2.034,2.313 0.392,0.153 10 CLTS 1.642,1.488 2.034,1.641 0.392,0.153 10 CLTE 2.072,0.731 2.228,0.904 0.156,0.174 10 6 2.072,2.066 2.225,2.211 0.154,0.146 10 5 2.072,1.408 2.228,1.554 0.156,0.146 10 3 5.035,0.802 5.427,0.955 0.392,0.153 10 CLTB 5.035,1.453 5.427,1.605 0.392,0.153 10 CLTE 5.035,2.146 5.427,2.299 0.392,0.153 10 CLTS 4.747,0.731 4.939,0.877 0.191,0.146 10 20 4.753,1.408 4.952,1.554 0.2,0.146 10 22 4.742,2.066 4.941,2.211 0.2,0.146 10 21

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Illumination Rate Info Illumination rate information 0.00 ms. to 2162.65 ms. Value is output according to ambient light levels -
Body Electrical > Main Body > Data List
Tester Display
Illumination Rate Info
50003 123 61
OK:

Normal condition listed above is displayed.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the I61 automatic light control sensor connector.


b.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I13-22 (CLTE) - I61-3 (CLTE) Always Below 1 Ω
I13-21 (CLTS) - I61-5 (CLTS) Always Below 1 Ω
I13-20 (CLTB) - I61-6 (CLTB) Always Below 1 Ω
I13-22 (CLTE) - Body ground Always 10 kΩ or higher
I13-21 (CLTS) - Body ground Always 10 kΩ or higher
I13-20 (CLTB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
E173035
1.542,0.823 1.906,1.094 0.365,0.271 2.083,2 1.365,2.813 false 2.458,2.01 2.458,2.813 false 0.146,0.115 0.854,0.708 0.708,0.594 10 *a 1.083,2.833 1.771,3.208 0.688,0.375 10 CLTE 2.271,2.833 2.781,3.115 0.51,0.281 10 CLTB 1.635,0.875 2.104,1.302 0.469,0.427 10 I13
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))


Reconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I13-20 (CLTB) - I13-22 (CLTE) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
I13-22 (CLTE) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.
E161973
1.5,0.594 1.896,0.854 0.396,0.26 1.938,2.177 2.51,2.51 false 1.938,1.927 2.51,1.594 false 0.104,0.094 0.979,0.844 0.875,0.75 10 *a 2.542,2.438 3.354,2.854 0.813,0.417 10 CLTS 2.542,1.5 3.25,1.938 0.708,0.438 10 CLTE 1.583,0.635 2.208,1.167 0.625,0.531 10 I61
*a Component with harness connected
(Automatic Light Control Sensor)


Reconnect the I61 automatic light control sensor connector.


b.

Connect an oscilloscope to the automatic light control sensor connector.


c.
B113714
2.948,1.063 3.427,1.448 0.479,0.385 10 GND 1.844,1.177 2.438,1.604 0.594,0.427 10 A

Check the waveform.

OK:
Tester Connection Tool Setting Condition Specified Condition
I61-3 (CLTE) - I61-5 (CLTS) 5 V/DIV., 5 ms./DIV. Ignition switch ON, light control switch in AUTO position Correct waveform is as shown


HINT:

If the ambient light becomes brighter, width A becomes narrower.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR