CHECK AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY)
Disconnect the A35 AFS ECU (headlight swivel ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A35-22 (E1) - Body ground | W-B - Body ground | AFS ECU (headlight swivel ECU assembly) ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A35-15 (IG) - Body ground | LG - Body ground | AFS ECU (headlight swivel ECU assembly) power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the A35 AFS ECU (headlight swivel ECU assembly) connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A35-11 (RHE) - A35-22 (E1) | LG - W-B | LIN communication | Ignition switch off | Below 1 V |
| Ignition switch ON | Pulse generation | |||
| A35-12 (MPX1) - A35-22 (E1) | B - W-B | CAN communication | Ignition switch off | Below 1 V |
| Ignition switch ON | Pulse generation | |||
| A35-13 (MPX2) - A35-22 (E1) | W - W-B | CAN communication | Ignition switch off | Below 1 V |
| Ignition switch ON | Pulse generation |
If the result is not as specified, the AFS ECU (headlight swivel ECU assembly) may have a malfunction.
CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main body ECU (multiplex network body ECU) with 2 connectors | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main body ECU (multiplex network body ECU) | *2 | 2 connectors |
| *A | Main body ECU (multiplex network body ECU) with 3 connectors | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main body ECU (multiplex network body ECU) | *2 | 3 connectors |
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3D-39 (DIM) - Body ground | W - Body ground | High beam headlight drive output | Dimmer switch in high or high flash position | Below 1 V |
| Dimmer switch in low position | 11 to 14 V | |||
| I13-5 (HU) - Body ground | LG - Body ground | Dimmer switch high position signal input | Dimmer switch in high position | Below 1 V |
| Dimmer switch not in high position | Pulse generation*2
11 to 14 V*3 |
|||
| I13-20 (CLTB)*1 - I13-22 (CLTE)*1 | B - P | Automatic light control sensor power supply output | Ignition switch off | Below 1 V |
| Ignition switch ON, light control switch in AUTO position | 11 to 14 V | |||
| I13-21 (CLTS)*1 - Body ground | G - Body ground | Automatic light control sensor signal input | Ignition switch off | Below 1 V |
| Automatic light control system operates | Pulse generation
(See waveform 1) |
|||
| I13-28 (A) - Body ground | G - Body ground | Light control switch AUTO position signal input | Light control switch in AUTO position | Below 1 V |
| Light control switch not in AUTO position | Pulse generation |
*1: w/ Automatic Light Control
*2: w/ Seat Position Memory System
*3: w/o Seat Position Memory System
If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.
Waveform 1
| Item | Content |
|---|---|
| Tool setting | 5 V/DIV., 5 ms./DIV. |
If the ambient light becomes brighter, width A becomes narrower.
CHECK INNER REAR VIEW MIRROR ASSEMBLY
Disconnect the S2 inner rear view mirror assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| S2-1 (E) - Body ground | W-B - Body ground | Inner rear view mirror assembly ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| S2-4 (IG) - Body ground | GR - Body ground | Inner rear view mirror assembly power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the S2 inner rear view mirror assembly connector.
Measure the voltage or check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| S2-5 (LIN) - S2-1 (E) | LG - W-B | LIN communication | Ignition switch off | Below 1 V |
| Automatic high beam system operating | Pulse generation
(See waveform 1) |
If the result is not as specified, the inner rear view mirror assembly may have a malfunction.
Waveform 1
| Item | Content |
|---|---|
| Tool setting | 2 V/DIV., 20 ms./DIV. |