Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM2030EQ _59 Vehicle Exterior _014682 EXTERIOR PANELS / TRIM _0074753 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


PROCEDURE

Hide 75561 1.INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP

NOTICE:

When installing new clips, remove the double-sided tape remaining where the clips will be installed on the body and clean the body with a non-residue solvent.


a.
B235312
2.938,0.854 2.604,0.479 true 1.917,1.021 1.302,0.469 1.302,0.469 1.156,0.469 true 2.938,0.844 3.313,1.104 0.375,0.26 10 *1 0.979,0.406 1.542,0.698 0.563,0.292 10 *a
*1 Adhesive
*a 2 to 3 mm Bead of Adhesive


Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to new roof drip side finish moulding clips.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F))



b.

Press and install the 2 roof drip side finish moulding clips.


c.

Install the clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the 2 roof drip side finish moulding clips after lightly applying adhesive (3M DP-105 or equivalent).

B280084
1.281,1.063 1.281,0.427 1.281,0.427 2.51,0.427 false 2.313,1.073 2.313,0.427 false 4.885,1.052 4.885,0.417 4.885,0.417 6.479,0.417 false 5.917,1.063 5.917,0.417 false 1.677,0.125 1.979,0.354 0.302,0.229 12 *A 5.271,0.135 5.698,0.427 0.427,0.292 12 *B 2.542,0.323 2.917,0.573 0.375,0.25 10 *1 6.531,0.313 6.896,0.583 0.365,0.271 10 *1 1.958,1.854 2.198,2.063 0.24,0.208 10 a 1.969,0.573 2.208,0.813 0.24,0.24 10 a 2.229,2.427 2.49,2.677 0.26,0.25 10 B 1.344,2.427 1.583,2.677 0.24,0.25 10 A 5.563,1.854 5.771,2.083 0.208,0.229 10 b 5.573,0.583 5.823,0.813 0.25,0.229 10 b 5.813,2.427 6.177,2.74 0.365,0.313 10 F 4.927,2.438 5.25,2.698 0.323,0.26 10 E 2.052,2.948 2.292,3.188 0.24,0.24 10 D 1.385,2.948 1.688,3.219 0.302,0.271 10 C 5.75,2.969 6.01,3.198 0.26,0.229 10 H 5.094,2.969 5.406,3.219 0.313,0.25 10 G 0.625,2.958 0.906,3.271 0.281,0.313 10 a-a 4.271,2.99 4.552,3.302 0.281,0.313 10 b-b
*A for Front Side *B for Rear Side
*1 Protruding Part - -


Standard Dimension
Installation Area Dimension Measurement
for Front Side A 4.0 mm (0.157 in.)
B 4.0 mm (0.157 in.)
C 1.8 mm (0.0709 in.)
D 1.8 mm (0.0709 in.)
for Rear Side E 4.0 mm (0.157 in.)
F 4.0 mm (0.157 in.)
G 1.8 mm (0.0709 in.)
H 1.8 mm (0.0709 in.)


d.

Install the roof drip center side finish moulding when 20 minutes or more have elapsed after pressing and installing 2 new roof drip side finish moulding clips.

HINT:
·

Initial hardening time: 20 minutes

·

Complete hardening time: 48 hours




Hide 75556C 2.INSTALL CENTER ROOF DRIP SIDE FINISH MOULDING

a.
B280083

Engage the 2 clips and install the center roof drip side finish moulding.