Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2012.02–2015.04
RM2030EQ _51 Engine / Hybrid System _014642 CRUISE CONTROL _0074459 CRUISE CONTROL SYSTEM U

CRUISE CONTROL  CRUISE CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Select the following menu items: Powertrain / Cruise Control / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
CCS Vehicle Spd Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Actual vehicle speed -
CCS Mem Vehicle Spd Stored vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Actual stored vehicle speed -
Throttle Opening Angle Required throttle opening angle min.: 0°, max.: 124.50° Actual required throttle opening angle -
Cruise Control Cruise control system active condition ON or OFF ON: Cruise control activated
OFF: Cruise control deactivated
-
Main SW M-CPU Cruise control switch signal (Main CPU) ON or OFF ON: Cruise control switch (ON-OFF button) pushed
OFF: Cruise control switch (ON-OFF button) released
-
CCS Ready M-CPU Cruise control system standby condition (Main CPU) ON or OFF Each time cruise control switch (ON-OFF button) is pushed, ON/OFF changes -
CCS Indicator M-CPU Cruise control indicator light illumination signal (Main CPU) ON or OFF ON: Cruise control indicator light illuminated
OFF: Cruise control indicator light not on
-
Cancel Switch CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -/SET switch signal ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
RES/ACC Switch +/RES switch signal ON or OFF ON: +/RES switch on
OFF: +/RES switch off
-
Stop Light Switch 1 Stop light switch signal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Stop Light Switch 2 Stop light switch signal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Cruise Operation Status Transmission range sensor signal ON or OFF ON: Cruise control operated
OFF: Cruise control operation stopped
-
Brake Cancel Switch Brake cancel signal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
HINT:
·

If any DTCs are output, the value for a measurement item may be incorrect.


·

If any DTCs are output, perform troubleshooting accordingly. After repair, confirm relevant values using Data List.





PERFORM ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Select the following menu items: Body / Combination Meter / Active Test.


e.

Perform "Active Test" according to the display on intelligent tester.

HINT:

The ignition switch must be turned on to proceed with the Active Test using the intelligent tester.


Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Lamp Cruise Cruise control indicator light Cruise control indicator light ON / OFF -
Indicat. SET Cruise control SET indicator light Cruise control SET indicator light ON / OFF -