Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2012.02–2015.04
RM2030EQ _59 Vehicle Exterior _014675 WINDOW / GLASS _0074675 POWER WINDOW CONTROL SYSTEM Y

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the power window control system.

·

*: Use the intelligent tester.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points in the problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms


Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.SYSTEM CHECK
4.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
for RHD with Smart Entry and Start System A
for RHD without Smart Entry and Start System B
for LHD



A

5.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

B

6.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
5.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
ECU is connected, communication line is normal A
ECU is connected, communication line is malfunctioning B



A

6.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

B

6.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Use the intelligent tester to check if the LIN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
No DTCs output A
DTCs output B



A

7.CHECK FOR DTC*

B

7.CHECK FOR DTC*
a.

Check for DTCs and note any codes that are output.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124

b.

Clear the DTCs.

Body Electrical > D-Door Motor > Clear DTCs
50002 124

c.

Recheck for DTCs.

Body Electrical > D-Door Motor > Trouble Codes
50001 124

Result:
Result Proceed to
No DTCs output A
DTCs output B



A

8.PROBLEM SYMPTOMS TABLE

B

8.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in problem symptoms table A
Fault is listed in problem symptoms table B



A

9.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

10.ADJUST, REPAIR OR REPLACE
9.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

10.ADJUST, REPAIR OR REPLACE
10.ADJUST, REPAIR OR REPLACE
a.

Check if driver door window regulator, power window regulator motor assembly (for driver door), door glass or door glass run has been removed and reinstalled.


Result:
Result Proceed to
Driver door window regulator, power window regulator motor assembly (for driver door), door glass or door glass run has been removed and reinstalled. A
None of the driver door window regulator, power window regulator motor assembly (for driver door), door glass or door glass run has been removed and reinstalled. B



A

11.INITIALIZE POWER WINDOW REGULATOR MOTOR ASSEMBLY

B

12.CONFIRMATION TEST
11.INITIALIZE POWER WINDOW REGULATOR MOTOR ASSEMBLY
a.

If the driver door window regulator or power window regulator motor assembly (for driver door) have been removed and reinstalled, perform "Initialize Power Window Control System" (initialization of the pulse sensor) for the driver door glass.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

HINT:

If "Initialize Power Window Control System" (initialization of the pulse sensor) has not been performed, the auto operation function, jam protection function, key-linked operation function*, wireless transmitter-linked operation function* and key-off operation function will not operate or will operate incorrectly.

*: This function is set through the customize function, as it is off by default.




Result:
Proceed to
NEXT



NEXT

12.CONFIRMATION TEST
12.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END