Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0076659 TOYOTA PARKING ASSIST-SENSOR SYSTEM U

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  TERMINALS OF ECU  


CLEARANCE WARNING ECU ASSEMBLY


E220917
3.497,0.109 3.894,0.347 0.397,0.238 3.599,0.155 3.828,0.337 0.23,0.182 10 I82

a.

Disconnect the I82 connector from the clearance warning ECU assembly.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I82-9 (CLSW) - I82-30 (E) B - BR Back sonar or clearance sonar switch assembly power source signal Engine switch on (IG), clearance sonar main switch on 11 to 14 V
I82-9 (CLSW) - I82-30 (E) B - BR Back sonar or clearance sonar switch assembly power source signal Engine switch on (IG), clearance sonar main switch off Below 1 V
I82-1 (IG) - I82-30 (E) Y - BR IG power source signal Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
I82-30 (E) - Body ground BR - Body ground Ground Always Below 1 Ω


c.

Reconnect the I82 connector to the clearance warning ECU assembly.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I82-22 (BOR) - I82-30 (E) V - BR Power source for rear sensor circuit Engine switch off Below 1 V
Engine switch on (IG), clearance sonar main switch on 7.2 to 8.8 V
I82-8 (SOF) - I82-30 (E) P - BR Front sensor communication signal (Front clearance sonar sensor) Engine switch on (IG), clearance sonar main switch on, shift lever in R Pulse generation
(See waveform 2)
I82-13 (ER) - I82-30 (E) R - BR Clearance warning buzzer signal Buzzer sounding Pulse generation
(See waveform 1)
I82-23 (E1) - I82-30 (E) GR - BR Ground for rear clearance sonar Always Below 1 V
I82-6 (E5) - I82-30 (E) W - BR Ground for front clearance sonar Always Below 1 V
I82-4 (BOF) - I82-30 (E) R - BR Power source for front sensor circuit Engine switch off Below 1 V
Engine switch on (IG), clearance sonar main switch on 7.2 to 8.8 V
I82-24 (SOR) - I82-30 (E) R - BR Rear sensor communication signal (Rear clearance sonar sensor) Engine switch on (IG), clearance sonar main switch on, shift lever in R Pulse generation
(See waveform 2)


e.

Using an oscilloscope, check waveform 1.

i.
E227014
0.083,1.677 0.552,1.938 0.469,0.26 10 GND

Waveform 1 (Reference)

Item Content
Terminal No. (Symbol) I82-13 (ER) - I82-30 (E)
Tool Setting 2 V/DIV., 500 μsec./DIV.
Vehicle Condition When sonar detects obstacle (buzzer sounds)
Buzzer volume M2 (Medium volume)

HINT:

The amplitude of the waveform changes according to the set volume.




f.

Using an oscilloscope, check waveform 2.

i.
E231486
0.188,0.927 0.625,1.146 0.438,0.219 10 GND 0.188,1.542 0.719,1.792 0.531,0.25 10 GND 0.052,0.604 0.458,0.771 0.406,0.167 10 CH: 1 0.052,1.229 0.458,1.396 0.406,0.167 10 CH: 2

Waveform 2 (Reference)

Item Content
Terminal No. (Symbol)
·

CH: 1 I82-8 (SOF) - I82-30 (E)

·

CH: 2 I82-24 (SOR) - I82-30 (E)


Tool Setting 5 V/DIV., 1 msec./DIV.
Condition Engine switch on (IG), clearance sonar main switch on, shift lever in R

HINT:

The waveforms for CH1 and CH2 are same.