Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0076659 TOYOTA PARKING ASSIST-SENSOR SYSTEM D

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  SYSTEM DESCRIPTION  


GENERAL


a.

This system uses ultrasonic sensors to detect any obstacles at the corners and the rear of the vehicle. The system then informs the driver of the distance between the sensors and an obstacle as well as its position by indicating it on the multi-information display (in the combination meter assembly) and by sounding a buzzer.



FUNCTION OF COMPONENTS


Component Function
No. 1 Ultrasonic Sensor (4) Detects the distance between the vehicle and an obstacle
No. 1 Clearance Warning Buzzer Sounds to inform the driver according to the distance to an obstacle
Multi-information Display on Combination Meter Assembly
·

Displays the location of an obstacle and the approximate distance between the vehicle and the obstacle

·

Displays a malfunction of the ultrasonic sensor to inform the driver


Combination Meter Assembly Transmits the vehicle speed signal to the clearance warning ECU assembly
Back Sonar or Clearance Sonar Switch Assembly Operating this switch enables, disables or cuts off the operation of the Toyota parking assist-sensor system
Clearance Warning ECU Assembly
·

Judges the approximate distance between the vehicle and an obstacle based on the signals from the ultrasonic sensors and sends it to the multi-information display

·

Sounds the buzzer


Main Body ECU (Multiplex Network Body ECU) Transmits the destination information to the clearance warning ECU assembly
ECM Transmits the shift position signal to the clearance warning ECU assembly
Air Conditioning Amplifier Assembly Transmits the temperature information to the clearance warning ECU assembly


OPERATION EXPLANATION


a.

The operating conditions of each ultrasonic sensor differ according to the installation position as shown in the table below.

Installation Position Operating Condition
Front Corner Sensor
·

Engine switch is on (IG).

·

Clearance sonar main switch is on.

·

Shift lever is in any position other than P.

·

Vehicle speed is less than approximately 9 km/h (5.6 mph). The sensors stop operating when the vehicle speed exceeds approximately 13 km/h (8.1 mph), and start operating when the vehicle speed drops below approximately 9 km/h (5.6 mph).


Rear Corner Sensor
·

Engine switch is on (IG).

·

Clearance sonar main switch is on.

·

Shift lever is in R.



When the system operates, the clearance warning ECU assembly transmits ultrasonic waves from the ultrasonic sensors. If these waves encounter an obstacle within one or more of the sensors ranges, the waves are reflected back to the sensors, which transmit them to the clearance warning ECU assembly.

Based on this information, the clearance warning ECU assembly sends signals to the multi-information display and the clearance warning buzzer. The approximate distance between the vehicle and the obstacle is then indicated, and the buzzer sounds.

HINT:

Refer to Detection Range Measurement and Display Inspection (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>OPERATION CHECK).




COMMUNICATION SIGNALS OF COMPONENTS


HINT:
·

Allocation refers to the process of the clearance warning ECU assembly setting aside IDs for the sensors.

·

The vehicle has the sensors arranged in 2 groups. There is a front series and a rear series. The sensors are connected in a "daisy chain".



a.

Initialization mode:

An ID is allocated to each sensor and sensor diagnosis is performed.

E236268E02
1.958,1.25 1.625,0.844 1.625,0.844 1.396,0.844 false 2.656,1.156 2.656,0.281 2.656,0.281 2.979,0.281 false 5.25,1.229 5.604,0.823 5.604,0.823 5.823,0.823 false 5.24,2.594 5.604,2.958 5.604,2.958 5.823,2.958 false 1.979,2.573 1.625,2.927 1.625,2.927 1.396,2.927 false 5.865,0.74 7.063,0.917 1.198,0.177 10 false Rear Right Sensor 5.865,2.885 6.938,3.052 1.073,0.167 10 false Rear Left Sensor 0.667,1.802 1.042,1.958 0.375,0.156 10 false Front 0.177,0.771 1.365,0.917 1.188,0.146 10 false Front Right Sensor 0.26,2.865 1.365,3.01 1.104,0.146 10 false Front Left Sensor 3.021,0.208 5.26,0.396 2.24,0.188 10 false Clearance Warning ECU Assembly

i.

When the initial check is operating (the engine switch is on (IG) and the clearance sonar main switch is on), the clearance warning ECU assembly provides power to the first sensors in each series (front left sensor and rear right sensor).


ii.

After the power is supplied, the front left sensor and rear right sensor enter standby mode to receive an ID from the ECU. When a certain amount of time has elapsed, the ECU sends an ID allocation signal to these sensors.


iii.

The front left sensor and rear right sensors receive the ID allocation signal from the ECU and perform self-diagnosis. When the sensor self-diagnosis is complete, the ECU sends an ID allocation confirmation signal to the sensors.


iv.

After the ID allocation confirmation is performed, the ECU provides power to the second sensors in each series (front right sensor and rear left sensor) via the first sensors. In the same manner as the first sensors, the second sensors enter standby mode. When a certain amount of time has elapsed, the ECU sends an ID allocation signal to the second sensors. Initialization ends when ID allocation to all ultrasonic sensors is complete.



b.

Detection mode:

After initialization mode is completed, the system switches into detection mode. In detection mode, the clearance warning ECU assembly sends information request signals and sensor activation signals to the ultrasonic sensors and receives detection result signals from the sensors.

i.

The ECU regularly sends ID signals, information request signals, and sensor activation signals to each ultrasonic sensor according to the communication schedule.


ii.

When a certain amount of time has elapsed (sensor detection operation is completed), the ECU sends an ID signal to the sensor to receive a detection result signal.


iii.

The ultrasonic sensor sends a detection result signal or detection information signal to the ECU.


iv.

The above operation is performed repeatedly for each ultrasonic sensor.