Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM2030EQ _59 Vehicle Exterior _014678 MIRROR (EXT) _0074700 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Driver Side Power Mirror cannot be Adjusted with Power Mirror Switch  


SYSTEM DESCRIPTION

When the mirror adjust switch is operated, the main body ECU (multiplex network body ECU) detects the switch operation and sends the mirror adjust switch signal to the outer mirror control ECU assembly (driver door) via CAN communication. On receiving the signal, the outer mirror control ECU assembly (driver door) operates the vertical and horizontal mirror motors, which are built into the mirror sub-assembly (driver door), to adjust the mirror surface position.

WIRING DIAGRAM

B293969E68
0.146,4.26 1.365,4.677 1.219,0.417 10 false Outer Mirror Switch Assembly 0.146,4.083 1.292,4.385 1.146,0.302 10 false K16*1, J12*2 1.844,4.052 2.177,4.313 0.333,0.26 10 false I12 1.844,4.229 3.469,4.677 1.625,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 0.896,0.875 1.438,1.167 0.542,0.292 10 false MSW 1.344,0.781 1.542,1.021 0.198,0.24 10 false 1 2,0.781 2.302,1.031 0.302,0.25 10 false 14 1.344,2.104 1.604,2.365 0.26,0.26 10 false 3 2.01,2.104 2.375,2.354 0.365,0.25 10 false 13 1.344,3.385 1.625,3.646 0.281,0.26 10 false 2 2.01,3.385 2.292,3.646 0.281,0.26 10 false 15 1.042,2.208 1.417,2.458 0.375,0.25 10 false M+ 1.146,3.5 1.396,3.719 0.25,0.219 10 false E 2.25,0.875 2.823,1.177 0.573,0.302 10 false MIRS 2.25,2.219 2.969,2.656 0.719,0.438 10 false MIRB 2.25,3.49 2.896,3.813 0.646,0.323 10 false MIRE 1,5.333 3,5.563 2,0.229 10 false : CAN Communication Line 2.76,1.625 3.24,1.896 0.479,0.271 10 false CAN 4.073,1.625 4.396,1.771 0.323,0.146 10 false CAN 4.594,0.875 5.417,1.104 0.823,0.229 10 false LMHR*1 4.604,2.208 5.167,2.531 0.563,0.323 10 false LM+R*1 4.604,3.5 5.417,3.802 0.813,0.302 10 false LMVR*1 5.219,0.771 5.438,1.083 0.219,0.313 10 false 9 5.219,2.115 5.448,2.365 0.229,0.25 10 false 10 5.219,3.396 5.427,3.625 0.208,0.229 10 false 1 3.865,4.24 5.427,4.823 1.563,0.583 10 false Outer Mirror Control ECU Assembly (Driver Door) 3.865,4.063 5.292,4.396 1.427,0.333 10 false z5*1, z6*2 5.729,4.094 7.021,4.75 1.292,0.656 10 false Mirror Sub-assembly (Driver Door) 4.583,1.042 5.406,1.271 0.823,0.229 10 false RMHR*2 4.594,2.375 5.156,2.698 0.563,0.323 10 false RM+R*2 4.583,3.656 5.396,3.958 0.813,0.302 10 false RMVR*2 5.865,5.135 7.156,5.792 1.292,0.656 10 false *1: for LHD 5.865,5.417 7.156,5.823 1.292,0.406 10 false *2: for RHD

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check for CAN communication system DTCs.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

OK:

CAN communication DTC is not output.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH ASSEMBLY)

NG

GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Selection SW (R) Mirror select switch signal for RH mirror*2 ON or OFF ON: Mirror select switch in R position
OFF: Mirror select switch off or in L position
-
Mirror Selection SW (L) Mirror select switch signal for LH mirror*1 ON or OFF ON: Mirror select switch in L position
OFF: Mirror select switch off or in R position
-
Mirror Position SW (R) Mirror adjust switch signal (Right) ON or OFF ON: Mirror adjust switch pressed right
OFF: Mirror adjust switch not pressed right
Check with the mirror select switch in the R position.
Mirror Position SW (L) Mirror adjust switch signal (Left) ON or OFF ON: Mirror adjust switch pressed left
OFF: Mirror adjust switch not pressed left
Check with the mirror select switch in the R position.
Mirror Position SW (Up) Mirror adjust switch signal (Up) ON or OFF ON: Mirror adjust switch pressed up
OFF: Mirror adjust switch not pressed up
Check with the mirror select switch in the R position.
Mirror Position SW (Dwn) Mirror adjust switch signal (Down) ON or OFF ON: Mirror adjust switch pressed down
OFF: Mirror adjust switch not pressed down
Check with the mirror select switch in the R position.

*1: for LHD

*2: for RHD


Body Electrical > Main Body > Data List
Tester Display
Mirror Selection SW (R)
Mirror Selection SW (L)
Mirror Position SW (R)
Mirror Position SW (L)
Mirror Position SW (Up)
Mirror Position SW (Dwn)
50003 123 98,99,100,101,102,103
OK:

On the intelligent tester screen, ON or OFF is displayed for each item according to the table above.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)

NG

5.INSPECT OUTER MIRROR SWITCH ASSEMBLY
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)
a.

for LHD

i.

Enter the following menus: Body / Mirror L / Active Test.


ii.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Mirror L > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Mirror Up/Down Mirror vertical operation Up / Down
·

Operate with engine switch on (IG) and the vehicle stopped.

·

This test tilts the mirror up or down.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Mirror Right/Left Mirror horizontal operation Right / Left
·

Operate with engine switch on (IG) and the vehicle stopped.

·

This test tilts the mirror right or left

·

This operation can be confirmed by watching the mirror move in the desired direction.


Body Electrical > Mirror L > Active Test
Tester Display
Mirror Up/Down
50004 225 2
Body Electrical > Mirror L > Active Test
Tester Display
Mirror Right/Left
50004 225 3
OK:

Power mirror operation is normal.




b.

for RHD

i.

Enter the following menus: Body / Mirror R / Active Test.


ii.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Mirror R > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Mirror Up/Down Mirror vertical operation Up / Down
·

Operate with engine switch on (IG) and the vehicle stopped.

·

This test tilts the mirror up or down.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Mirror Right/Left Mirror horizontal operation Right / Left
·

Operate with engine switch on (IG) and the vehicle stopped.

·

This test tilts the mirror right or left

·

This operation can be confirmed by watching the mirror move in the desired direction.


Body Electrical > Mirror R > Active Test
Tester Display
Mirror Up/Down
50004 224 2
Body Electrical > Mirror R > Active Test
Tester Display
Mirror Fold/Return
50004 224 4
OK:

Power mirror operation is normal.




Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

4.INSPECT MIRROR SUB-ASSEMBLY (DRIVER DOOR)
4.INSPECT MIRROR SUB-ASSEMBLY (DRIVER DOOR)
a.
B294038C10
1.5,1.552 1.99,1.844 0.49,0.292 1.25,2.5 0.792,2.5 false 1.438,2.729 1.438,3.198 1.438,3.198 1.615,3.198 false 1.313,2.729 1.313,3.198 1.313,3.198 1.125,3.198 false 0.729,1.667 1.104,2.031 0.375,0.365 10 false *a 1.677,1.604 2.083,1.927 0.406,0.323 10 false z5 0.333,2.427 0.958,2.688 0.625,0.26 10 false LMVR 1.677,3.125 2.219,3.354 0.542,0.229 10 false LM+R 0.688,3.115 1.271,3.313 0.583,0.198 10 false LMHR
*a Component without harness connected
(Mirror Sub-assembly LH)


for LHD

i.

Remove the mirror sub-assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


ii.

Apply battery voltage and check the operation of the mirror sub-assembly LH.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal z5-1 (LMVR)
Battery negative (-) → Terminal z5-10 (LM+R)
Turns upward
Battery negative (-) → Terminal z5-1 (LMVR)
Battery positive (+) → Terminal z5-10 (LM+R)
Turns downward
Battery positive (+) → Terminal z5-9 (LMHR)
Battery negative (-) → Terminal z5-10 (LM+R)
Turns left
Battery negative (-) → Terminal z5-9 (LMHR)
Battery positive (+) → Terminal z5-10 (LM+R)
Turns right




b.
B294037C10
1.51,1.615 2,1.906 0.49,0.292 1.271,2.5 0.906,2.5 false 1.427,2.708 1.427,3.135 1.427,3.135 1.698,3.135 false 1.302,2.708 1.302,3.135 1.302,3.135 1.042,3.135 false 1.771,3.052 2.281,3.292 0.51,0.24 10 false RM+R 0.438,1.719 0.781,2.083 0.344,0.365 10 false *a 1.656,1.677 1.99,1.917 0.333,0.24 10 false z6 0.573,3.052 1.229,3.365 0.656,0.313 10 false RMHR 0.385,2.417 0.99,2.75 0.604,0.333 10 false RMVR
*a Component without harness connected
(Mirror Sub-assembly RH)


for RHD

i.

Remove the mirror sub-assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


ii.

Apply battery voltage and check the operation of the mirror sub-assembly RH.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal z6-1 (RMVR)
Battery negative (-) → Terminal z6-10 (RM+R)
Turns upward
Battery negative (-) → Terminal z6-1 (RMVR)
Battery positive (+) → Terminal z6-10 (RM+R)
Turns downward
Battery positive (+) → Terminal z6-9 (RMHR)
Battery negative (-) → Terminal z6-10 (RM+R)
Turns left
Battery negative (-) → Terminal z6-9 (RMHR)
Battery positive (+) → Terminal z6-10 (RM+R)
Turns right




Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

REPLACE MIRROR SUB-ASSEMBLY (DRIVER DOOR)

5.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.
B294031C11
1.156,2.802 1.51,3.052 0.354,0.25 1.833,2.813 2.188,3.063 0.354,0.25 1.729,0.844 1.729,0.292 1.729,0.292 1.906,0.292 false 1.719,1.854 1.719,2.385 1.719,2.385 1.896,2.385 false 1.979,3.771 1.979,4.302 1.979,4.302 1.708,4.302 false 2.146,3.771 2.146,4.427 2.146,4.427 2.51,4.427 false 2.333,3.771 2.333,4.135 2.333,4.135 2.51,4.135 false 1.417,4.219 1.896,4.573 0.479,0.354 10 false M+ 1.938,2.313 2.406,2.75 0.469,0.438 10 false *1 1.938,0.198 2.406,0.604 0.469,0.406 10 false *2 2.563,4.333 2.771,4.604 0.208,0.271 10 false E 2.563,4.042 3.052,4.292 0.49,0.25 10 false MSW 0.479,2.823 0.75,3.125 0.271,0.302 10 false *a 1.208,2.844 1.625,3.104 0.417,0.26 10 false K16 1.563,2.844 1.979,3.104 0.417,0.26 10 false *A 1.896,2.844 2.313,3.104 0.417,0.26 10 false J12 2.26,2.844 2.677,3.104 0.417,0.26 10 false *B
*A for LHD
*B for RHD
*1 Mirror Adjust Switch
*2 Mirror Select Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Remove the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K16-3 (M+) - K16-2 (E)*1
J12-3 (M+) - J12-2 (E)*2
Mirror adjust switch pressed up 90 to 110 Ω
Mirror adjust switch pressed down 437 to 503 Ω
Mirror adjust switch pressed left 744 to 856 Ω
Mirror adjust switch pressed right 225 to 275 Ω
K16-1 (MSW) - K16-2 (E)*1
J12-1 (MSW) - J12-2 (E)*2
Mirror select switch L 90 to 110 Ω
Mirror select switch R Below 10 Ω
Mirror select switch off 10 kΩ or higher


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU)

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU)
a.

Disconnect the K16*1 or J12*2 connector from the outer mirror switch assembly.


b.

Disconnect the I12 connector from the main body ECU (multiplex network body ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K16-2 (E) - I12-15 (MIRE)*1
J12-2 (E) - I12-15 (MIRE)*2
Always Below 1 Ω
K16-3 (M+) - I12-13 (MIRB)*1
J12-3 (M+) - I12-13 (MIRB)*2
Always Below 1 Ω
K16-1 (MSW) - I12-14 (MIRS)*1
J12-1 (MSW) - I12-14 (MIRS)*2
Always Below 1 Ω
K16-2 (E) - Body ground*1
J12-2 (E) - Body ground*2
Always 10 kΩ or higher
K16-3 (M+) - Body ground*1
J12-3 (M+) - Body ground*2
Always 10 kΩ or higher
K16-1 (MSW) - Body ground*1
J12-1 (MSW) - Body ground*2
Always 10 kΩ or higher


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR