Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM2030EQ _59 Vehicle Exterior _014678 MIRROR (EXT) _0074700 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Power Mirror cannot be Adjusted with Power Mirror Switch  


SYSTEM DESCRIPTION

The main body ECU (multiplex network body ECU) detects the mirror adjust switch status and sends the signal to the outer mirror control ECU assembly via CAN communication. On receiving the signal, each outer mirror control ECU assembly operates the vertical and horizontal mirror motors to adjust the mirror surface position.

WIRING DIAGRAM

B294043E17
1.219,2.823 1.479,3.115 0.26,0.292 10 false E 1.115,1.625 1.635,1.948 0.521,0.323 10 false M+ 0.958,0.552 1.625,0.865 0.667,0.313 10 false MSW 1.417,0.427 1.51,0.563 0.094,0.135 10 false 1 1.417,1.51 1.781,1.833 0.365,0.323 10 false 3 1.417,2.719 1.969,3.083 0.552,0.365 10 false 2 2.938,0.417 3.24,0.635 0.302,0.219 10 false 14 2.938,1.5 3.292,1.74 0.354,0.24 10 false 13 2.938,2.698 3.281,2.906 0.344,0.208 10 false 15 2.917,3.458 3.354,3.729 0.438,0.271 10 false I12 0.25,3.552 1.448,4.042 1.198,0.49 10 false Outer Mirror Switch Assembly 0.25,3.385 1.479,3.688 1.229,0.302 10 false K16*1, J12*2 2.927,3.625 4.573,4.083 1.646,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 5.302,1.313 6.844,1.75 1.542,0.438 10 false Outer Mirror Control ECU Assembly (Driver Door) 5.323,3.76 6.875,4.344 1.552,0.583 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 3.219,1.625 3.76,1.885 0.542,0.26 10 false MIRB 3.219,0.521 3.823,0.844 0.604,0.323 10 false MIRS 3.219,2.823 3.76,3.125 0.542,0.302 10 false MIRE 3.969,2.313 4.448,2.552 0.479,0.24 10 false CAN 5.542,3.083 6.063,3.354 0.521,0.271 10 false CAN 1.021,4.438 2.969,4.688 1.948,0.25 10 false : CAN Communication Line 5.542,0.635 6.083,0.958 0.542,0.323 10 false CAN

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

OK:

CAN communication DTC is not output.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH ASSEMBLY)

NG

GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Selection SW (R) Mirror select switch signal for RH mirror ON or OFF ON: Mirror select switch in R position
OFF: Mirror select switch off or in L position
-
Mirror Selection SW (L) Mirror select switch signal for LH mirror ON or OFF ON: Mirror select switch in L position
OFF: Mirror select switch off or in R position
-
Mirror Position SW (R) Mirror adjust switch signal (Right) ON or OFF ON: Mirror adjust switch pressed right
OFF: Mirror adjust switch not pressed right
Check with the mirror select switch in any position except neutral
Mirror Position SW (L) Mirror adjust switch signal (Left) ON or OFF ON: Mirror adjust switch pressed left
OFF: Mirror adjust switch not pressed left
Check with the mirror select switch in any position except neutral
Mirror Position SW (Up) Mirror adjust switch signal (Up) ON or OFF ON: Mirror adjust switch pressed up
OFF: Mirror adjust switch not pressed up
Check with the mirror select switch in any position except neutral
Mirror Position SW (Dwn) Mirror adjust switch signal (Down) ON or OFF ON: Mirror adjust switch pressed down
OFF: Mirror adjust switch not pressed down
Check with the mirror select switch in any position except neutral
Body Electrical > Main Body > Data List
Tester Display
Mirror Selection SW (R)
Mirror Selection SW (L)
Mirror Position SW (R)
Mirror Position SW (L)
Mirror Position SW (Up)
Mirror Position SW (Dwn)
50003 123 98,99,100,101,102,103
OK:

On the intelligent tester screen, ON or OFF is displayed for each item according to the table above.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT OUTER MIRROR SWITCH ASSEMBLY
3.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.
B294031C11
1.156,2.802 1.51,3.052 0.354,0.25 1.833,2.813 2.188,3.063 0.354,0.25 1.729,0.844 1.729,0.292 1.729,0.292 1.906,0.292 false 1.719,1.854 1.719,2.385 1.719,2.385 1.896,2.385 false 1.979,3.771 1.979,4.302 1.979,4.302 1.708,4.302 false 2.146,3.771 2.146,4.427 2.146,4.427 2.51,4.427 false 2.333,3.771 2.333,4.135 2.333,4.135 2.51,4.135 false 1.417,4.219 1.896,4.573 0.479,0.354 10 false M+ 1.938,2.313 2.406,2.75 0.469,0.438 10 false *1 1.938,0.198 2.406,0.604 0.469,0.406 10 false *2 2.563,4.333 2.771,4.604 0.208,0.271 10 false E 2.563,4.042 3.052,4.292 0.49,0.25 10 false MSW 0.479,2.823 0.75,3.125 0.271,0.302 10 false *a 1.208,2.844 1.625,3.104 0.417,0.26 10 false K16 1.563,2.844 1.979,3.104 0.417,0.26 10 false *A 1.896,2.844 2.313,3.104 0.417,0.26 10 false J12 2.26,2.844 2.677,3.104 0.417,0.26 10 false *B
*A for LHD
*B for RHD
*1 Mirror Adjust Switch
*2 Mirror Select Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Remove the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K16-3 (M+) - K16-2 (E)*1
J12-3 (M+) - J12-2 (E)*2
Mirror adjust switch pressed up*3 90 to 110 Ω
Mirror adjust switch pressed down*3 437 to 503 Ω
Mirror adjust switch pressed left*3 744 to 856 Ω
Mirror adjust switch pressed right*3 225 to 275 Ω
K16-1 (MSW) - K16-2 (E)*1
J12-1 (MSW) - J12-2 (E)*2
Mirror select switch R Below 10 Ω
Mirror select switch L 90 to 110 Ω
Mirror select switch off 10 kΩ or higher


*1: for LHD

*2: for RHD

*3: Set the mirror select switch to L or R.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU)

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU)
a.

Disconnect the K16*1 or J12*2 connector from the outer mirror switch assembly.


b.

Disconnect the I12 connector from the main body ECU (multiplex network body ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K16-2 (E) - I12-15 (MIRE)*1
J12-2 (E) - I12-15 (MIRE)*2
Always Below 1 Ω
K16-3 (M+) - I12-13 (MIRB)*1
J12-3 (M+) - I12-13 (MIRB)*2
Always Below 1 Ω
K16-1 (MSW) - I12-14 (MIRS)*1
J12-1 (MSW) - I12-14 (MIRS)*2
Always Below 1 Ω
K16-2 (E) - Body ground*1
J12-2 (E) - Body ground*2
Always 10 kΩ or higher
K16-3 (M+) - Body ground*1
J12-3 (M+) - Body ground*2
Always 10 kΩ or higher
K16-1 (MSW) - Body ground*1
J12-1 (MSW) - Body ground*2
Always 10 kΩ or higher


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR