Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM2030EQ _59 Vehicle Exterior _014678 MIRROR (EXT) _0074700 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Power Mirror Surface Position is not Memorized  


SYSTEM DESCRIPTION

If either the M1 or M2 seat memory switch is pressed, the outer mirror control ECU assembly (driver door) detects the switch operation and sends the seat memory switch signal to the main body ECU (multiplex network body ECU) via CAN communication. On receiving the seat memory switch signal, the main body ECU (multiplex network body ECU) sends the memory request signal to each outer mirror control ECU assembly via CAN communication. When receiving this signal, each outer mirror control ECU assembly stores the mirror surface position based on information from the mirror position sensor, which is built into the mirror sub-assembly.

HINT:

Each mirror sub-assembly has a built-in mirror vertical position sensor and mirror horizontal position sensor.


NOTICE:
·

The mirror surface position will not be memorized if the engine switch is not on (IG).

·

The mirror surface position will not be stored if the seat memory SET switch and 2 of the seat memory switches are pressed simultaneously.

·

If the operation fails, the mirror surface position will not be memorized until the seat memory SET switch is turned off.

·

The mirror surface position will not be memorized when the mirror is operated manually.



WIRING DIAGRAM

B313725E09
0.094,6.021 1.74,6.719 1.646,0.698 10 false Main Body ECU (Multiplex Network Body ECU) 0.854,5.219 1.531,5.573 0.677,0.354 10 false CANN 0.615,7.24 2.49,7.573 1.875,0.333 10 false : CAN Communication Line 3.427,6.729 3.969,6.969 0.542,0.24 10 false CANN 3.188,4.802 4.771,5.344 1.583,0.542 10 false Outer Mirror Control ECU Assembly (Driver Door) 5.479,2.219 7.073,2.656 1.594,0.438 10 false Mirror Sub-assembly LH 5.469,7.219 7.135,7.521 1.667,0.302 10 false Mirror Sub-assembly RH 2.854,7.229 5.083,7.792 2.229,0.563 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 3.448,3.083 3.99,3.396 0.542,0.313 10 false CANN 0.865,2.604 1.625,3.219 0.76,0.615 10 false CANP 3.438,5.979 3.979,6.271 0.542,0.292 10 false CANP 3.448,1.51 4.052,1.896 0.604,0.385 10 false CANP 4.5,4.292 4.917,4.594 0.417,0.302 10 false K12 4.51,3.854 4.969,4.115 0.458,0.26 10 false K12 4.5,3.427 4.917,3.688 0.417,0.26 10 false K12 4.5,3 4.875,3.292 0.375,0.292 10 false K12 3.063,6.708 3.438,6.958 0.375,0.25 10 false J13 3.063,5.958 3.448,6.208 0.385,0.25 10 false J13 4.021,5.771 4.552,6.073 0.531,0.302 10 false RVC 4.063,6.896 4.458,7.188 0.396,0.292 10 false RE1 3.958,6.135 4.552,6.448 0.594,0.313 10 false VSSR 3.948,6.51 4.563,6.875 0.615,0.365 10 false HSSR 4.052,0.313 4.615,0.708 0.563,0.396 10 false LVC 4.083,1.896 4.542,2.167 0.458,0.271 10 false LE1 3.958,0.844 4.656,1.198 0.698,0.354 10 false VSSR 3.958,1.365 4.51,1.667 0.552,0.302 10 false HSSR 4.135,3.01 4.5,3.313 0.365,0.302 10 false M1 4.094,3.854 4.542,4.198 0.448,0.344 10 false MM 3.896,4.292 4.49,4.583 0.594,0.292 10 false MSWE 4.135,3.448 4.479,3.708 0.344,0.26 10 false M2 5.74,3.021 6.188,3.365 0.448,0.344 10 false M1 5.74,3.854 6.333,4.177 0.594,0.323 10 false MRY 5.74,4.302 6.042,4.615 0.302,0.313 10 false E 5.74,3.448 6.104,3.74 0.365,0.292 10 false M2 5.542,2.906 5.76,3.167 0.219,0.26 10 false 4 5.542,3.75 5.781,4.031 0.24,0.281 10 false 2 5.542,4.208 5.771,4.417 0.229,0.208 10 false 1 5.552,3.333 5.76,3.542 0.208,0.208 10 false 3 4.583,0.094 4.813,0.375 0.229,0.281 10 false 5 4.552,1.875 4.948,2.198 0.396,0.323 10 false z5 4.552,1.354 4.917,1.688 0.365,0.333 10 false z5 4.552,0.823 4.885,1.188 0.333,0.365 10 false z5 4.552,0.302 4.885,0.531 0.333,0.229 10 false z5 4.552,1.677 4.875,1.969 0.323,0.292 10 false 14 3.135,5.75 3.417,6.125 0.281,0.375 10 false 9 3.125,1.292 3.385,1.552 0.26,0.26 10 false 9 1.354,5.031 1.771,5.375 0.417,0.344 10 false 10 0.094,5.844 0.615,6.219 0.521,0.375 10 false I12 4.552,5.771 4.896,6.052 0.344,0.281 10 false z6 4.552,6.135 4.927,6.417 0.375,0.281 10 false z6 4.563,6.5 4.865,6.792 0.302,0.292 10 false z6 4.563,6.875 4.865,7.135 0.302,0.26 10 false z6 5.594,4.979 7.063,5.438 1.469,0.458 10 false Seat Memory Switch 5.594,4.833 6.135,5.156 0.542,0.323 10 false K15 3.135,6.5 3.354,6.74 0.219,0.24 10 false 8 1.365,2.427 1.844,2.802 0.479,0.375 10 false 9 3.125,2.865 3.365,3.146 0.24,0.281 10 false 8 4.542,4.083 4.854,4.365 0.313,0.281 10 false 13 4.594,0.635 4.875,0.906 0.281,0.271 10 false 6 4.542,1.156 4.854,1.406 0.313,0.25 10 false 13 4.594,2.802 4.729,2.969 0.135,0.167 10 false 2 4.583,3.667 4.833,3.927 0.25,0.26 10 false 1 4.594,3.24 4.865,3.563 0.271,0.323 10 false 3 4.594,5.573 4.771,5.792 0.177,0.219 10 false 5 4.552,6.708 4.823,6.948 0.271,0.24 10 false 14 4.594,5.958 4.792,6.188 0.198,0.229 10 false 6 4.552,6.333 4.844,6.563 0.292,0.229 10 false 13 3.052,1.51 3.438,1.802 0.385,0.292 10 false K12 3.052,3.073 3.469,3.427 0.417,0.354 10 false K12 0.208,0.146 1.167,0.573 0.958,0.427 12 false for LHD:

B313725E10
0.125,6.031 1.771,6.74 1.646,0.708 10 false Main Body ECU (Multiplex Network Body ECU) 0.854,5.198 1.49,5.531 0.635,0.333 10 false CANN 0.615,7.229 2.531,7.594 1.917,0.365 10 false : CAN Communication Line 3.438,6.719 3.927,6.979 0.49,0.26 10 false CANN 3.229,4.823 4.792,5.385 1.563,0.563 10 false Outer Mirror Control ECU Assembly (Driver Door) 5.479,7.208 7.156,7.563 1.677,0.354 10 false Mirror Sub-assembly LH 5.479,2.208 7.021,2.51 1.542,0.302 10 false Mirror Sub-assembly RH 2.854,7.229 5.063,7.677 2.208,0.448 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 3.438,3.094 4.042,3.458 0.604,0.365 10 false CANN 0.854,2.604 1.469,2.927 0.615,0.323 10 false CANP 3.427,5.969 3.896,6.198 0.469,0.229 10 false CANP 3.438,1.521 4.052,1.854 0.615,0.333 10 false CANP 4.521,4.292 4.948,4.542 0.427,0.25 10 false J13 4.521,3.854 4.885,4.125 0.365,0.271 10 false J13 4.521,3.427 4.865,3.646 0.344,0.219 10 false J13 4.521,3 4.938,3.313 0.417,0.313 10 false J13 3.042,6.698 3.385,6.979 0.344,0.281 10 false K12 3.042,5.958 3.417,6.24 0.375,0.281 10 false K12 4.063,5.792 4.563,6.104 0.5,0.313 10 false LVC 4.083,6.885 4.51,7.146 0.427,0.26 10 false LE1 3.958,6.146 4.51,6.385 0.552,0.24 10 false VSSR 3.958,6.51 4.552,6.813 0.594,0.302 10 false HSSR 4.031,0.323 4.521,0.677 0.49,0.354 10 false RVC 4.073,1.896 4.573,2.167 0.5,0.271 10 false RE1 3.958,0.854 4.521,1.125 0.563,0.271 10 false VSSR 3.958,1.375 4.563,1.656 0.604,0.281 10 false HSSR 4.146,3.021 4.563,3.375 0.417,0.354 10 false M1 4.094,3.865 4.448,4.135 0.354,0.271 10 false MM 3.896,4.292 4.542,4.583 0.646,0.292 10 false MSWE 4.146,3.458 4.51,3.729 0.365,0.271 10 false M2 5.76,3.021 6.24,3.354 0.479,0.333 10 false M1 5.76,3.854 6.219,4.146 0.458,0.292 10 false MRY 5.76,4.302 6.021,4.552 0.26,0.25 10 false E 5.76,3.448 6.125,3.708 0.365,0.26 10 false M2 5.552,2.906 5.74,3.125 0.188,0.219 10 false 4 5.552,3.729 5.813,4.01 0.26,0.281 10 false 2 5.542,4.177 5.771,4.417 0.229,0.24 10 false 1 5.552,3.333 5.771,3.573 0.219,0.24 10 false 3 4.594,0.104 4.854,0.438 0.26,0.333 10 false 5 4.542,1.875 4.969,2.302 0.427,0.427 10 false z6 4.552,0.302 4.906,0.563 0.354,0.26 10 false z6 4.542,0.833 4.802,1.042 0.26,0.208 10 false z6 4.552,1.354 4.896,1.594 0.344,0.24 10 false z6 4.542,1.677 5.01,2.073 0.469,0.396 10 false 14 3.135,5.75 3.344,5.99 0.208,0.24 10 false 9 3.125,1.302 3.375,1.625 0.25,0.323 10 false 9 1.354,5.042 1.729,5.385 0.375,0.344 10 false 10 0.125,5.854 0.646,6.177 0.521,0.323 10 false I12 4.563,5.771 4.813,5.979 0.25,0.208 10 false z5 4.563,6.146 4.875,6.365 0.313,0.219 10 false z5 4.552,6.5 4.917,6.74 0.365,0.24 10 false z5 4.563,6.875 4.896,7.156 0.333,0.281 10 false z5 5.594,4.979 6.938,5.344 1.344,0.365 10 false Seat Memory Switch 5.594,4.813 5.917,5.083 0.323,0.271 10 false J16 3.135,6.49 3.302,6.74 0.167,0.25 10 false 8 1.354,2.438 1.625,2.75 0.271,0.313 10 false 9 3.125,2.865 3.323,3.104 0.198,0.24 10 false 8 4.542,4.094 4.833,4.323 0.292,0.229 10 false 13 4.594,0.635 4.823,0.875 0.229,0.24 10 false 6 4.542,1.156 4.813,1.406 0.271,0.25 10 false 13 4.583,2.802 4.813,3.115 0.229,0.313 10 false 2 4.594,3.656 4.823,3.906 0.229,0.25 10 false 1 4.594,3.24 4.833,3.479 0.24,0.24 10 false 3 4.583,5.573 4.781,5.813 0.198,0.24 10 false 5 4.552,6.698 4.854,6.938 0.302,0.24 10 false 14 4.594,5.969 4.802,6.198 0.208,0.229 10 false 6 4.552,6.333 4.854,6.563 0.302,0.229 10 false 13 3.063,3.073 3.396,3.323 0.333,0.25 10 false J13 3.063,1.51 3.531,1.813 0.469,0.302 10 false J13 0.156,0.104 1.24,0.698 1.083,0.594 12 false for RHD:

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

OK:

CAN communication DTC is not output.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)

NG

GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

2.READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Mirror R or Mirror L / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Mirror L > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 signal ON or OFF ON: Seat memory switch M1 on
OFF: Seat memory switch M1 off
-
Seat Memory Switch2 Seat memory switch M2 signal ON or OFF ON: Seat memory switch M2 on
OFF: Seat memory switch M2 off
-
Seat Memory Set SW Seat memory switch SET signal ON or OFF ON: Seat memory switch SET on
OFF: Seat memory switch SET off
-
Body Electrical > Mirror L > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Switch3
Seat Memory Set SW
50003 225 1,2,3,4
Body Electrical > Mirror R > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 signal ON or OFF ON: Seat memory switch M1 on
OFF: Seat memory switch M1 off
-
Seat Memory Switch2 Seat memory switch M2 signal ON or OFF ON: Seat memory switch M2 on
OFF: Seat memory switch M2 off
-
Seat Memory Set SW Seat memory switch SET signal ON or OFF ON: Seat memory switch SET on
OFF: Seat memory switch SET off
-
Body Electrical > Mirror R > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Switch3
Seat Memory Set SW
50003 224 1,2,3,4
OK:

The intelligent tester display changes between ON and OFF according to the switch operations.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT MEMORY SWITCH FUNCTION

NG

9.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - OUTER MIRROR CONTROL ECU ASSEMBLY)
3.CHECK SEAT MEMORY SWITCH FUNCTION
a.

When any seat memory switch (M1 or M2 switch) is pressed, check that the driver seat moves to the memorized position.

OK:

The driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

4.CHECK MEMORY AND REACTIVATION FUNCTION

NG

GO TO POWER SEAT CONTROL SYSTEM (Power Seat does not Return to Memorized Position)

4.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C03
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Left Fully


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

Result:
Result Proceed to
Memory and reactivation functions on both mirrors are not normal A
Memory and reactivation functions on RH side mirror are not normal B
Memory and reactivation functions on LH side mirror are not normal C




A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

5.REPLACE MIRROR SUB-ASSEMBLY RH

C

7.REPLACE MIRROR SUB-ASSEMBLY LH
5.REPLACE MIRROR SUB-ASSEMBLY RH
a.

Replace the mirror sub-assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK MEMORY AND REACTIVATION FUNCTION
6.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C04
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Left Fully


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

OK:

Memory and reactivation function is normal.



Result:
Proceed to
OK
NG



OK

END (MIRROR SUB-ASSEMBLY RH WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

7.REPLACE MIRROR SUB-ASSEMBLY LH
a.

Replace the mirror sub-assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK MEMORY AND REACTIVATION FUNCTION
8.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C05
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Left Fully


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

OK:

Memory and reactivation function is normal.



Result:
Proceed to
OK
NG



OK

END (MIRROR SUB-ASSEMBLY LH WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)

9.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - OUTER MIRROR CONTROL ECU ASSEMBLY)
a.

Disconnect the K12*1 or J13*2connector from the outer mirror control ECU assembly.


b.

Disconnect the K15*1 or J16*2connector from the seat memory switch.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K15-2 (MRY) - K12-1 (MM) Always Below 1 Ω
K15-4 (M1) - K12-2 (M1) Always Below 1 Ω
K15-3 (M2) - K12-3 (M2) Always Below 1 Ω
K15-1 (E) - K12-13 (MSWE) Always Below 1 Ω
K15-2 (MRY) - Body ground Always 10 kΩ or higher
K15-4 (M1) - Body ground Always 10 kΩ or higher
K15-3 (M2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
J16-2 (MRY) - J13-1 (MM) Always Below 1 Ω
J16-4 (M1) - J13-2 (M1) Always Below 1 Ω
J16-3 (M2) - J13-3 (M2) Always Below 1 Ω
J16-1 (E) - J13-13 (MSWE) Always Below 1 Ω
J16-2 (MRY) - Body ground Always 10 kΩ or higher
J16-4 (M1) - Body ground Always 10 kΩ or higher
J16-3 (M2) - Body ground Always 10 kΩ or higher


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

10.INSPECT SEAT MEMORY SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT SEAT MEMORY SWITCH
a.
B307747C02
1.438,3.917 1.021,4.25 false 1.615,3.917 1.219,4.427 false 1.896,3.927 2.375,4.406 false 2.083,3.906 2.573,4.24 false 0.354,3.021 0.802,3.417 0.448,0.396 10 false *a 0.354,1.594 0.708,1.844 0.354,0.25 10 false *B 0.354,0.219 0.885,0.615 0.531,0.396 10 false *A 0.76,4.177 1.198,4.396 0.438,0.219 10 false M1 1.083,4.417 1.521,4.635 0.438,0.219 10 false M2 2.635,4.167 3.073,4.385 0.438,0.219 10 false E 2.292,4.438 2.729,4.656 0.438,0.219 10 false MRY
*A for LHD
*B for RHD
*a Component without harness connected
(Seat Memory Switch)


Remove the seat memory switch.

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K15-4 (M1) - K15-1 (E) M1 Switch off → on 10 kΩ or higher → Below 1 Ω
K15-3 (M2) - K15-1 (E) M2 Switch off → on 10 kΩ or higher → Below 1 Ω
K15-2 (MRY) - K15-1 (E) SET Switch off → on 10 kΩ or higher → Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
J16-4 (M1) - J16-1 (E) M1 Switch off → on 10 kΩ or higher → Below 1 Ω
J16-3 (M2) - J16-1 (E) M2 Switch off → on 10 kΩ or higher → Below 1 Ω
J16-2 (MRY) - J16-1 (E) SET Switch off → on 10 kΩ or higher → Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

REPLACE SEAT MEMORY SWITCH