Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM U

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  TERMINALS OF ECU  


TCM


C133222
3.385,0.094 3.781,0.333 0.396,0.24 3.5,0.125 3.781,0.302 0.281,0.177 10 E7

HINT:

Each TCM terminal standard voltage is shown in the table below.

In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the TCM terminals.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E7-15 (R) - E7-8 (E1) L - BR R shift position switch signal Ignition switch ON and shift lever in R 11 to 14 V
Ignition switch ON and shift lever not in R Below 1 V
E7-16 (D) - E7-8 (E1) R - BR D shift position switch signal Ignition switch ON and shift lever in D and S 11 to 14 V
Ignition switch ON and shift lever not in D or S Below 1 V
E7-12 (STP) - E7-8 (E1) GR - BR Stop light switch signal Brake pedal is depressed 7.5 to 14 V
Brake pedal is released Below 1.5 V
E7-11 (NSW) - E7-8 (E1) R - BR Park/neutral switch signal Ignition switch ON and shift lever in P or N Below 2 V
Ignition switch ON and shift lever not in P or N 11 to 14 V
E7-10 (STA) - E7-8 (E1) Y - BR Starter signal Cranking (shift lever in P or N) 11 to 14 V
E7-3 (SPD) - E7-8 (E1) G - BR Vehicle speed signal from combination meter Vehicle driving Pulse generation
E7-1 (BATT) - E7-8 (E1) W - BR Battery (for measuring battery voltage and for TCM memory) Always 11 to 14 V
E7-13 (IGSW) - E7-8 (E1) B - BR IG signal Ignition switch ON 11 to 14 V
E7-18 (+B) - E7-8 (E1) W - BR Power source of TCM Ignition switch ON 11 to 14 V
E7-6 (CAN+) - E7-8 (E1) B - BR CAN communication line Ignition switch ON Pulse generation
E7-7 (CAN-) - E7-8 (E1) Y - BR CAN communication line Ignition switch ON Pulse generation


ECM


HINT:

Each ECM terminal standard voltage is shown in the table below.

In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration below as a reference for the ECM terminals.

C239275
2.453,0.355 2.85,0.593 0.397,0.238 2.532,0.401 2.807,0.583 0.275,0.182 10 E26 5.894,0.355 6.291,0.593 0.397,0.238 5.975,0.407 6.253,0.589 0.278,0.182 10 A25


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A25-37 (S) - E26-49 (E1) G - BR S shift position switch signal Ignition switch ON and shift lever in S 11 to 14 V
Ignition switch ON and shift lever not in S Below 1 V
A25-34 (SFTU) - E26-49 (E1) R - BR Up shift switch signal Ignition switch ON and shift lever in S 11 to 14 V
Ignition switch ON and shift lever in "+" (Up shift) Below 1 V
A25-50 (SFTD) - E26-49 (E1) V - BR Down shift switch signal Ignition switch ON and shift lever in S 11 to 14 V
Ignition switch ON and shift lever in "-" (Down shift) Below 1 V