Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM J

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  ECU Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, voltage from the ECM's MREL terminal is applied to the EFI MAIN relay. This causes the contacts of the EFI MAIN relay to close, which supplies power to terminal +B of the TCM.

WIRING DIAGRAM

C240516E01
6.355,5.102 6.715,5.257 0.36,0.156 10 TCM 0.675,4.903 1.203,5.078 0.528,0.175 10 Battery 0.491,1.678 1.52,1.845 1.029,0.168 10 EFI MAIN NO. 1 2.962,2.207 3.661,2.375 0.699,0.168 10 EFI MAIN 3.711,1.69 4.404,1.862 0.693,0.172 10 EFI NO. 2 2.804,3.335 4.287,3.519 1.484,0.183 10 No. 1 Integration Relay 5.389,1.971 5.905,2.116 0.516,0.145 10 to ECM 5.389,1.092 5.905,1.237 0.516,0.145 10 to ECM 6.138,3.716 6.348,3.855 0.21,0.139 10 E1 6.138,1.531 6.377,1.687 0.239,0.156 10 +B 1.662,1.333 1.811,1.492 0.15,0.159 10 1 1.617,1.531 1.811,1.69 0.195,0.159 10 1B 2.369,2.94 2.519,3.099 0.15,0.159 10 2 2.257,3.123 2.458,3.282 0.2,0.159 10 1E 4.702,0.927 4.832,1.085 0.13,0.158 10 9 4.646,1.099 4.848,1.245 0.202,0.147 10 1C 4.695,1.365 4.803,1.518 0.108,0.153 10 4 4.695,1.791 4.803,1.944 0.108,0.153 10 7 6.355,4.948 6.659,5.114 0.304,0.166 10 E7 5.832,1.432 6.021,1.591 0.189,0.158 10 18 5.878,3.597 5.986,3.75 0.108,0.153 10 8 4.646,1.531 4.848,1.677 0.202,0.147 10 1A 4.646,1.974 4.848,2.121 0.202,0.147 10 1C 5.389,0.642 5.905,0.787 0.516,0.145 10 to ECM 4.652,0.646 4.854,0.792 0.202,0.147 10 1C 4.669,0.474 4.858,0.632 0.189,0.158 10 10 0.588,3.835 1.156,4.01 0.568,0.175 10 FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TCM - BODY GROUND)
a.
C189544C05
1.552,0.906 2.042,1.208 0.49,0.302 1.031,2.177 0.417,2.938 false 0.167,0.146 0.396,0.344 0.229,0.198 10 *a 1.688,0.969 1.969,1.125 0.281,0.156 10 E7 0.292,2.969 0.49,3.125 0.198,0.156 10 E1
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E7-8 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT ECU TERMINAL VOLTAGE (+B TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ECU TERMINAL VOLTAGE (+B TERMINAL)
a.
C189544C06
0.491,0.433 0.711,0.641 0.22,0.208 10 *a 1.53,0.901 2.023,1.199 0.493,0.298 1.667,0.964 1.945,1.12 0.278,0.156 10 E7 0.704,2.932 1.196,3.078 0.492,0.146 10 +B 1.123,2.352 0.865,2.886 false
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-18 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (TCM - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (TCM - NO. 1 INTEGRATION RELAY)
a.

Remove the NO. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the NO. 1 integration relay connector.


c.

Disconnect the TCM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E7-18 (+B) - 1A-4 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E7-18 (+B) or 1A-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

GO TO ECM POWER SOURCE CIRCUIT (ENGINE CONTROL SYSTEM / SFI SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR