Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0711  Transmission Fluid Temperature Sensor "A" Performance  


DESCRIPTION

The Automatic Transmission Fluid (ATF) temperature sensor converts the fluid temperature into a resistance value for use by the TCM.

C274654E01
1.833,1.458 1.531,1.896 false 0.313,0.646 1.844,0.844 1.531,0.198 10 Resistance 1.01,3.823 1.958,4.031 0.948,0.208 10 Temperature 1.917,1.385 3.104,1.594 1.188,0.208 10 Acceptable range

The TCM applies a voltage to the temperature sensor through terminal THO1 of the TCM.

The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.

The TCM calculates the fluid temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0711 Transmission Fluid Temperature Sensor "A" Performance One of the following conditions (A) or (B) is met:
(A) Both (a) and (b) are detected: (2-trip detection logic)
·

(a) Intake air and engine coolant temperatures are more than -10°C (14°F) at engine start


·

(b) After normal driving for over 18 min. and 20 sec. and 8 km (5 mile) or more, ATF temperature is less than 20°C (68°F)


(B) Both (a) and (b) are detected: (2-trip detection logic)
·

(a) Engine coolant temperature is less than 35°C (95°F) at engine start


·

(b) ATF temperature is 110°C (230°F) or more when engine coolant temperature reaches 60°C (140°F)


ATF temperature sensor Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates that there is a problem with output signals from the automatic transmission fluid (ATF) temperature sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature and detects an open or short in the ATF temperature circuit or a fault of the ATF temperature sensor.

After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the TCM interprets this as a fault turns on the MIL, and stores the DTC.

WIRING DIAGRAM

C133262E09
5.635,4.521 6.281,4.708 0.646,0.188 10 TCM 1.698,3.844 3.01,4.24 1.313,0.396 10 Transaxle Assembly 5.094,1.802 5.635,1.969 0.542,0.167 10 THO1 5.094,2.927 5.635,3.094 0.542,0.167 10 E2 1.01,3.292 2.656,3.656 1.646,0.365 10 ATF Temperature Sensor

CAUTION / NOTICE / HINT

NOTICE:

If DTCs P0711 and P2610 are output simultaneously, confirm that the ATF temperature is as specified in "Normal Condition" using the intelligent tester first. When the ATF temperature is as specified in "Normal Condition", perform troubleshooting for DTC P2610 (See pageEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the value listed under "Normal Condition" are reference values.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the intelligent tester, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 215°C (419°F)
·

After stall speed test: Approximately 80°C (176°F)

·

While engine is cold:

Equal to ambient temperature


If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or short circuited
Powertrain > ECT > Data List
Tester Display
A/T Oil Temperature 1
50003 235 161
HINT:

When DTC P0712 is output and the intelligent tester indicates 150°C (302°F) or more, there is a short circuit.

When DTC P0713 is output and the intelligent tester indicates -40°C (-40°F), there is an open circuit.

Measure the resistance between terminal THO1 (OT) and body ground.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or more Short circuit

HINT:

If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected.

It is not necessary to inspect the circuit when P0711 is set.




PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0711)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 235

e.

Read the DTCs using the intelligent tester.

Result:
Display (DTC Output) Proceed to
Only P0711 is output A
P0711 and other DTC B


HINT:

If any other codes besides P0711 are output, perform troubleshooting for those DTCs first.




A

2.CHECK TRANSMISSION FLUID LEVEL

B

2.CHECK TRANSMISSION FLUID LEVEL

OK:

Automatic transmission fluid level is correct.


Result:
Proceed to
OK
NG



OK

NG

ADJUST FLUID LEVEL