Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the TCM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)
·

NSW input signal is ON.

·

R input signal is ON.

·

D input signal is ON.


(B) All switches are OFF simultaneously for NSW, R and D.
·

Open or short in park/neutral position switch assembly circuit

·

Park/neutral position switch assembly

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends signals to the TCM.

For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the TCM according to the shift lever position (R or D). The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The TCM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C245544
4.938,1.302 5.208,1.583 0.271,0.281 10 16 5.406,4.25 5.802,4.458 0.396,0.208 10 E7 5.25,1.417 5.792,1.583 0.542,0.167 10 D 5.25,1.823 5.792,1.99 0.542,0.167 10 R 5.24,2.406 5.781,2.573 0.542,0.167 10 NSW 5.229,3.625 5.771,3.792 0.542,0.167 10 STA 4.948,1.708 5.313,2.115 0.365,0.406 10 15 4.958,2.313 5.25,2.552 0.292,0.24 10 11 4.948,3.521 5.26,3.844 0.313,0.323 10 10 5.719,4.25 6.323,4.448 0.604,0.198 10 TCM 0.292,1.646 1.25,2.198 0.958,0.552 10 from IG1 No. 1 Relay 1.344,2.417 2.26,2.792 0.917,0.375 10 to ST Relay 3.146,2.823 4.479,3.385 1.333,0.563 10 Park/Neutral Position Switch Assembly 1.771,1.844 2.5,2.031 0.729,0.188 10 BKUP LP 3.146,2.677 3.5,2.917 0.354,0.24 10 E4 4,1.313 4.302,1.635 0.302,0.323 10 7 4,1.708 4.208,2.01 0.208,0.302 10 2 3.146,1.51 3.479,1.771 0.333,0.26 10 1 3.146,2.323 3.438,2.563 0.292,0.24 10 9 4,2.313 4.198,2.573 0.198,0.26 10 4 3.75,1.313 4.135,1.625 0.385,0.313 10 DL 3.75,1.719 4.042,1.938 0.292,0.219 10 RL 3.313,1.479 3.667,1.76 0.354,0.281 10 RB 3.813,2.313 4.083,2.583 0.271,0.271 10 B 3.323,2.323 3.604,2.563 0.281,0.24 10 L

CAUTION / NOTICE / HINT

HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the intelligent tester, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status ON or OFF
·

ON: Shift lever is in P or N

·

OFF: Shift lever is not in P or N


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW Status (P Range) PNP switch status ON or OFF
·

ON: Shift lever is in R

·

OFF: Shift lever is not in R


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW Status (D Range) PNP switch status ON or OFF
·

ON: Shift lever is in D or S

·

OFF: Shift lever is not in D or S


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Powertrain > ECT > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (D Range)
50003 235 636,377,151


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.
C190067
0.438,1.573 0.771,1.844 0.333,0.271 1.646,1.594 2.083,1.063 false 2.125,0.896 2.469,1.115 0.344,0.219 10 RB 0.521,1.625 0.823,1.771 0.302,0.146 10 E4 0.219,0.24 0.531,0.552 0.313,0.313 10 *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E4-1 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)
a.
C190067
0.375,1.583 0.802,1.885 0.427,0.302 2.198,1.656 2.75,1.135 false 2.792,0.958 3.198,1.167 0.406,0.208 10 B 0.521,1.646 0.865,1.792 0.344,0.146 10 E4 0.167,0.188 0.583,0.563 0.417,0.375 10 *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E4-4 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
A107908
0.344,1.542 0.771,1.823 0.427,0.281 1.219,1.552 0.781,1.063 false 0.792,2.646 1.281,2 false 1.969,1.552 2.542,1.021 false 1.635,1.531 1.771,0.99 false 2,2.583 1.781,1.958 false 0.24,0.219 0.469,0.406 0.229,0.188 10 *a 0.667,0.917 0.885,1.094 0.219,0.177 10 B 0.708,2.656 0.917,2.833 0.208,0.177 10 L 2.573,0.906 2.885,1.083 0.313,0.177 10 RB 0.479,1.594 0.719,1.823 0.24,0.229 10 E4 1.698,0.74 2.01,0.917 0.313,0.177 10 RL 1.99,2.646 2.375,2.917 0.385,0.271 10 DL
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Shift Lever Position Specified Condition
E4-4 (B) - E4-9 (L) P or N Below 1 Ω
Except P and N 10 kΩ or higher
E4-1 (RB) - E4-2 (RL) R Below 1 Ω
Except R 10 kΩ or higher
E4-1 (RB) - E4-7 (DL) D, S, "+" or "-" Below 1 Ω
Except D, S, "+" and "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)

NG

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
a.
C189544
0.208,1.104 0.615,1.375 0.406,0.271 2.094,2.25 1.781,2.802 false 2.24,2.25 2.135,2.802 false 0.135,0.177 0.354,0.417 0.219,0.24 10 *a 0.354,1.156 0.667,1.313 0.313,0.156 10 E7 1.667,2.813 1.844,2.99 0.177,0.177 10 R 2.094,2.813 2.271,2.99 0.177,0.177 10 D
*a Front view of wire harness connector
(to TCM)


Connect the park/neutral position switch assembly connector.


b.

Disconnect the TCM connectors.


c.

Turn the ignition switch to ON, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

Standard Voltage:
Tester Connection Shift Lever Position Specified Condition
E7-15 (R) - Body ground R 11 to 14 V*
Except R Below 1 V
E7-16 (D) - Body ground D, S, "+" or "-" 11 to 14 V
Except D, S, "+" and "-" Below 1 V


HINT:

*: The voltage will drop slightly due to lighting up of the back up light.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
a.

Turn the ignition switch off.


b.

Disconnect the TCM connector.


c.

Disconnect the park/neutral position switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E4-4 (B) - E7-11 (NSW) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E4-4 (B) or E7-11 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR