Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The Automatic Transmission Fluid (ATF) temperature sensor converts the fluid temperature into a resistance value for use by the TCM.

C274654E01
1.833,1.458 1.531,1.896 false 0.313,0.646 1.844,0.844 1.531,0.198 10 Resistance 1.01,3.823 1.958,4.031 0.948,0.208 10 Temperature 1.917,1.385 3.104,1.594 1.188,0.208 10 Acceptable range

The TCM applies a voltage to the temperature sensor through terminal THO1 of the TCM.

The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.

The TCM calculates the fluid temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1-trip detection logic)
·

Short in ATF temperature sensor circuit

·

Transmission wire

·

ATF temperature sensor

·

TCM


Comes on DTC stored
P0713 Transmission Fluid Temperature Sensor "A" Circuit High Input ATF temperature sensor resistance is more than 156 kΩ for 0.5 seconds or more. Either of the following conditions is met (1 trip detection logic):
Condition (A): 394 seconds or more have elapsed after the engine start when engine coolant temperature or intake air temperature is -29.375°C (-20.875°F) or less.
Condition (B): 10 seconds or more have elapsed after the engine start when engine coolant temperature and intake air temperature are more than -29.375°C (- 20.875°F).
·

Open in ATF temperature sensor circuit

·

Transmission wire

·

ATF temperature sensor

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the automatic transmission fluid (ATF) temperature sensor circuit. The automatic transmission fluid (ATF) temperature sensor converts ATF temperature into an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature, and the TCM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 79 Ω*1 or more than 156 kΩ*2, the TCM interprets this as a fault in the ATF sensor or wiring. The TCM will turn on the MIL and store the DTC.

*1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.

*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

HINT:

The ATF temperature can be checked on the intelligent tester display.


WIRING DIAGRAM

C133262E09
5.635,4.521 6.281,4.708 0.646,0.188 10 TCM 1.698,3.844 3.01,4.24 1.313,0.396 10 Transaxle Assembly 5.094,1.802 5.635,1.969 0.542,0.167 10 THO1 5.094,2.927 5.635,3.094 0.542,0.167 10 E2 1.01,3.292 2.656,3.656 1.646,0.365 10 ATF Temperature Sensor

CAUTION / NOTICE / HINT

HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the intelligent tester, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 215°C (419°F)
·

After stall speed test: Approximately 80°C (176°F)

·

While engine is cold:

Equal to ambient temperature


If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or short circuited
Powertrain > ECT > Data List
Tester Display
A/T Oil Temperature 1
50003 235 161
HINT:

When DTC P0712 is output and the intelligent tester indicates 150°C (302°F) or more, there is a short circuit.

When DTC P0713 is output and the intelligent tester indicates -40°C (-40°F), there is an open circuit.

Measure the resistance between terminal THO1 (OT) and body ground.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or more Short circuit

HINT:

If the circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected.

It is not necessary to inspect the circuit when P0711 is set.




PROCEDURE

1.INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)
a.
C133212
2.306,0.623 2.698,0.772 0.392,0.149 10 THO1 2.281,1.173 2.478,1.322 0.197,0.149 10 E2 1.915,1.029 2.285,0.73 false 2.049,1.112 2.267,1.259 false 0.664,0.364 0.833,0.521 0.169,0.157 10 *a
*a Component without harness connected
(Transmission Wire)


Remove the TCM from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
17 (E2) - 18 (THO1) Always 79 Ω to 156 kΩ
17 (E2) - Body ground and other terminals Always 10 kΩ or higher
18 (THO1) - Body ground and other terminals Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range with the ATF temperature shown in the table below, the drivability of the vehicle may decrease.


ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ


Result:
Proceed to
OK
NG



OK

NG

2.INSPECT ATF TEMPERATURE SENSOR
2.INSPECT ATF TEMPERATURE SENSOR
a.
C133224
1.875,1.167 1.573,2.031 false 2.01,1.167 2.375,2.021 false 2.188,2.052 2.583,2.208 0.396,0.156 10 THO1 1.458,2.063 1.698,2.219 0.24,0.156 10 E2

Disconnect the ATF temperature sensor connector from the transmission wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E2 - THO1 Always 79 Ω to 156 kΩ
E2 - Body ground and other terminals Always 10 kΩ or higher
THO1 - Body ground and other terminals Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range with the ATF temperature shown in the table below, the drivability of the vehicle may decrease.


ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ


Result:
Proceed to
OK
NG



OK

NG