Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling when the brakes are suddenly applied while driving in the lock-up condition.

When the brake pedal is depressed, this switch sends a signal to the TCM. Then the TCM cancels the operation of the lock-up clutch while braking is in progress.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0724 Brake Switch "B" Circuit High The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (1.86 mph)) and GO (30 km/h (18.65 mph) or more) fashion 5 times. (2-trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during "stop and go" driving, the TCM interprets this as a fault in the stop light switch, illuminates the MIL, and stores the DTC. The vehicle must stop (less than 3 km/h (1.86 mph)) and go (30 km/h (18.65 mph) or more) five times for two consecutive driving cycles in order to set this DTC.

WIRING DIAGRAM

C204585
1.26,3.656 1.948,3.969 0.688,0.313 10 false Battery 1.115,2.365 1.823,2.542 0.708,0.177 10 false FL MAIN 1.5,1.406 1.875,1.615 0.375,0.208 10 false ALT 2.49,1.396 3.01,1.688 0.521,0.292 10 false STOP 3.146,2.094 4.271,2.271 1.125,0.177 10 false Stop Light Switch 5.219,1.26 5.552,1.458 0.333,0.198 10 false STP 5.219,3 5.448,3.198 0.229,0.198 10 false E1 4.917,1.25 5.281,1.448 0.365,0.198 10 false E7 3.167,1.917 3.583,2.115 0.417,0.198 10 false A33 4.927,3 5.219,3.198 0.292,0.198 10 false E7 4.927,1.052 5.156,1.25 0.229,0.198 10 false 12 3.99,1.146 4.219,1.344 0.229,0.198 10 false 1 4.01,1.719 4.24,1.917 0.229,0.198 10 false 4 3,1.719 3.229,1.917 0.229,0.198 10 false 3 3,1.135 3.229,1.333 0.229,0.198 10 false 2 4.958,2.802 5.188,3 0.229,0.198 10 false 8 5.698,4.354 6.083,4.521 0.385,0.167 10 false TCM

PROCEDURE

1.READ VALUE USING DATA LIST (STP SIGNAL)
HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / ECT / Data List.


f.

According to the display on the intelligent tester, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status ON or OFF Brake pedal is
·

ON: Depressed

·

OFF: Released


-
Powertrain > ECT > Data List
Tester Display
Stop Light Switch
50003 235 188
OK:

On the intelligent tester screen, ON or OFF is displayed accordingly.


NOTICE:

In the table above, the conditions listed under "Normal Condition" are reference conditions. Do not depend solely on these reference conditions when deciding whether a part is faulty.



Result:
Proceed to
OK
NG



OK

CHECK FOR INTERMITTENT PROBLEMS

NG

2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the stop light switch assembly installation.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

OK:

Stop light switch assembly is installed correctly.



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
a.
C189544
0.208,1.104 0.615,1.375 0.406,0.271 1.708,2.25 1.396,2.802 false 0.135,0.177 0.354,0.417 0.219,0.24 10 *a 0.354,1.156 0.667,1.313 0.313,0.156 10 E7 1.25,2.833 1.646,3.073 0.396,0.24 10 STP
*a Front view of wire harness connector
(to TCM)


Install the stop light switch assembly.


b.

Connect the stop light switch connector.


c.

Disconnect the TCM connector.


d.

Measure the voltage according to the value(s) in the table below when the brake pedal is depressed and released.

Standard Voltage:
Tester Connection Condition Specified Condition
E7-12 (STP) - Body ground Brake pedal is depressed 7.5 to 14 V
E7-12 (STP) - Body ground Brake pedal is released Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR