Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

Refer to the system description for DTC P2714 (See page Drivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>P2714).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1-trip detection logic).
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

When an open or short in the linear solenoid valve (SLT) circuit is detected, the TCM interprets this as a fault. The TCM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C133261
5.611,4.503 6.203,4.696 0.591,0.193 10 TCM 1.988,3.804 3.366,4.236 1.377,0.432 10 Transaxle Assembly 5.098,1.85 5.644,2.018 0.545,0.168 10 SLT+ 5.869,1.045 6.414,1.212 0.545,0.168 10 +B 5.098,3.192 5.644,3.36 0.545,0.168 10 SLT- 1.603,2.312 3.658,2.696 2.055,0.384 10 Shift Solenoid Valve SLT

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SLT)
a.
C133212
1.771,0.719 2.24,0.448 false 1.906,0.979 2.292,1.146 false 2.333,1.094 2.688,1.24 0.354,0.146 10 SLT+ 2.271,0.344 2.604,0.49 0.333,0.146 10 SLT- 0.635,0.292 0.969,0.438 0.333,0.146 10 *a
*a Component without harness connected
(Transmission Wire)


Remove the TCM from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (SLT+) - 7 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
12 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
7 (SLT-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT SHIFT SOLENOID VALVE SLT
2.INSPECT SHIFT SOLENOID VALVE SLT
a.
C201747C02
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 0.49,0.521 0.667,0.719 0.177,0.198 10 1 2.531,0.5 2.708,0.698 0.177,0.198 10 2 1.177,4.198 1.385,4.406 0.208,0.208 10 (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 (+) 0.51,2.771 0.688,2.969 0.177,0.198 10 1 2.521,2.76 2.698,2.958 0.177,0.198 10 2 0.135,0.135 0.354,0.344 0.219,0.208 10 *1
*1 Shift Solenoid Valve SLT


Remove shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG