Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the TCM.

If the TCM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The TCM then illuminates the MIL and sets the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more applied to TCM for 20 seconds
(1 trip detection logic):
(a) Vehicle speed more than 20 km/h (12.43 mph)
(b) Engine speed more than 1000 rpm
(c) STA signal ON
·

Park/Neutral position switch assembly

·

Starter relay circuit

·

Cranking holding function circuit

·

TCM


Comes on DTC stored

WIRING DIAGRAM

C240539E05
6.333,2.281 6.656,2.458 0.323,0.177 10 false ECM 6.365,5.104 6.688,5.281 0.323,0.177 10 false TCM 6.167,1.104 6.458,1.281 0.292,0.177 10 false STA 6.167,1.615 6.51,1.792 0.344,0.177 10 false NSW 6.188,4.146 6.479,4.323 0.292,0.177 10 false STA 6.188,2.948 6.531,3.125 0.344,0.177 10 false NSW 4.479,3.333 4.74,3.51 0.26,0.177 10 false E4 4.844,2.74 5,2.917 0.156,0.177 10 false P 5.042,2.74 5.198,2.917 0.156,0.177 10 false N 4.667,3.125 4.823,3.302 0.156,0.177 10 false L 4.646,2.927 4.802,3.104 0.156,0.177 10 false B 5.823,1.167 6.135,1.344 0.313,0.177 10 false A25 5.823,1.625 6.104,1.802 0.281,0.177 10 false E26 5.906,0.969 6.042,1.115 0.135,0.146 10 false 9 5.865,1.427 6.052,1.573 0.188,0.146 10 false 65 3.729,3.417 3.927,3.594 0.198,0.177 10 false ST 3.458,2.792 3.615,2.969 0.156,0.177 10 false 3 4.063,2.792 4.219,2.969 0.156,0.177 10 false 5 4.063,3.229 4.219,3.406 0.156,0.177 10 false 2 3.458,3.229 3.615,3.406 0.156,0.177 10 false 1 2.906,2.708 3.177,2.885 0.271,0.177 10 false E9 2.938,2.521 3.094,2.698 0.156,0.177 10 false 1 0.958,3.146 1.156,3.323 0.198,0.177 10 false F2 0.99,2.948 1.146,3.125 0.156,0.177 10 false 1 1.792,3.792 2.229,3.969 0.438,0.177 10 false Starter 0.938,4.281 1.573,4.583 0.635,0.302 10 false Battery 2.688,1.802 3.292,1.979 0.604,0.177 10 false ST/AM2 5.875,2.844 6.052,3.021 0.177,0.177 10 false 11 5.885,4.031 6.063,4.208 0.177,0.177 10 false 10 4.479,3.01 4.635,3.188 0.156,0.177 10 false 9 5.26,2.844 5.417,3.021 0.156,0.177 10 false 4 5.927,4.448 6.031,4.625 0.104,0.177 10 false 8 6.188,4.552 6.479,4.729 0.292,0.177 10 false E1 4.448,1.594 5.219,1.927 0.771,0.333 10 false to Certification ECU 4.479,3.479 5.823,3.823 1.344,0.344 10 false Park/Neutral Position Switch Assembly 6.365,4.948 6.688,5.125 0.323,0.177 10 false E7 0.458,2.563 1.063,2.74 0.604,0.177 10 false FL MAIN

CAUTION / NOTICE / HINT

HINT:

The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine does not crank, proceed to the problem symptoms table (See pageEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Signal Starter signal Open or Close Open: Starter operating
Close: Starter not operating
-
Powertrain > ECT > Data List
Tester Display
Starter Signal
50003 235 193

e.

Crank the engine.


f.

Read the value displayed on the intelligent tester.

OK:
Tester Display Condition Specified Condition
Starter Signal Ignition switch ON Close
Starter Signal Engine is cranking Open



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
A107908C02
0.344,1.542 0.771,1.823 0.427,0.281 1.219,1.552 0.781,1.063 false 0.792,2.646 1.281,2 false 1.969,1.552 2.542,1.021 false 0.24,0.219 0.469,0.406 0.229,0.188 10 *a 0.667,0.917 0.885,1.094 0.219,0.177 10 B 0.708,2.656 0.917,2.833 0.208,0.177 10 L 2.573,0.906 2.885,1.083 0.313,0.177 10 RB 0.479,1.594 0.667,1.771 0.188,0.177 10 E4
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
E4-4 (B) - E4-9 (L) P Below 1 Ω
N Below 1 Ω
Except P and N 10 kΩ or higher
E4-1 (RB) - E4-9 (L) P 10 kΩ or higher
R 10 kΩ or higher
N 10 kΩ or higher
D 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TCM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (TCM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.
C189544C01
1.563,0.875 2.052,1.177 0.49,0.302 1.479,2.25 0.896,2.979 false 0.24,0.271 0.458,0.51 0.219,0.24 10 *a 1.729,0.938 2.042,1.094 0.313,0.156 10 E7 0.698,3 1.135,3.156 0.438,0.156 10 STA
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Disconnect the park/neutral position switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E7-10 (STA) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Clear the DTCs.

Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > ECT > Clear DTCs
50002 235

e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / ECT/ Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 235

g.

Read the DTCs.

Result:
Result Proceed to
DTC is not output OK
DTC P0617 is output NG




OK

END

NG