Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM D

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  HYDRAULIC TEST  


PERFORM HYDRAULIC TEST


a.
C241958E03
0.906,4.073 1,4.219 false 2.625,4.167 3.125,4.417 0.5,0.25 10 false SST 0.896,4.25 1.438,4.542 0.542,0.292 10 false SST

Measure the line pressure.

CAUTION:

The line pressure test should always be carried out with at least 2 people. One person should observe the condition of wheels and wheel chocks while the other is performing the test.


NOTICE:
·

Perform a test at the normal operating Automatic Transmission Fluid (ATF) temperature: 50 to 80°C (122 to 176°F)

·

Be careful to prevent the SST hose from interfering with the exhaust pipe.

·

This check must be conducted after checking and confirming that the engine is normal.

·

Perform the test with the A/C off.

·

Do not perform the stall test for longer than 5 seconds.

·

When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.



i.

Warm up the Automatic Transmission Fluid (ATF).


ii.

Lift the vehicle up.


iii.

Remove the engine under cover.


iv.

Remove the test plug on the transaxle case front left side and install the SST.

SST
09992-00095  (09992-00231, 09992-00271)


v.

Lower the vehicle.


vi.

Fully apply the parking brake and chock the 4 wheels.


vii.

Connect the intelligent tester to the DLC3.


viii.

Start the engine.


ix.

Enter the following menus: Powertrain / ECT / Active Test / Control the Shift Position.

Powertrain > ECT > Active Test
Tester Display
Control the Shift Position
50004 235 116

x.

Move the shift lever to D, and then use the intelligent tester to hold 3rd gear using Active Test. Measure the line pressure while the engine is idling.

Specified Line Pressure
Condition D Position kPa (kgf/cm2, psi)
Idling 360 to 430 kPa
(3.7 to 4.4 kgf/cm2, 52 to 62 psi)


xi.

Turn the ignition switch off.


xii.
C241959

Disconnect the connector of the TCM.

HINT:

Disconnect the connector only when performing the D position stall test.



xiii.

Start the engine.


xiv.

Firmly depress the brake pedal, move the shift lever to D, depress the accelerator pedal all the way down, and check the line pressure while the stall test is performed.

Specified Line Pressure
Condition D Position kPa (kgf/cm2, psi)
Stall test 1160 to 1350 kPa
(11.8 to 13.8 kgf/cm2, 168 to 196 psi)


xv.

Turn the ignition switch off.


xvi.

Connect the TCM connector, depress the brake pedal firmly, move the shift lever to R, and check that the line pressure while the engine is idling and during the stall test.

Specified Line Pressure
Condition R Position kPa (kgf/cm2, psi)
Idling 800 to 950 kPa
(8.2 to 9.7 kgf/cm2, 116 to 138 psi)
Stall test 1900 to 2200 kPa
(19.4 to 22.4 kgf/cm2, 276 to 319 psi)


xvii.

Remove the SST, install the test plug.


xviii.

Clear the DTCs.

Evaluation
Test Result Possible Cause
Measured values are higher than the specified value in all positions
·

Shift solenoid valve (SLT) defective

·

Regulator valve defective


Measured values are lower than the specified value in all positions
·

Shift solenoid valve (SLT) defective

·

Regulator valve defective

·

Oil pump defective


Pressure is low in D only
·

D position circuit fluid leak

·

Clutch No. 1 (C1) defective


Pressure is low in R only
·

R position circuit fluid leak

·

Brake No. 2 (B2) defective

·

Brake No. 3 (B3) defective