Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM D

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  INITIALIZATION  


RESET TRANSAXLE COMPENSATION CODE


NOTICE:
·

If the following parts have been replaced, initialize the TCM and perform the following "Reset Memory" and "Perform Road Test to Allow TCM to learn" steps.

- Valve body assembly

- Shift solenoid valve SL3

- Shift solenoid valve SL4

- TCM

·

The transaxle compensation code can only be initialize with the intelligent tester.



HINT:

The TCM memorizes the condition that the ECT controls the automatic transaxle assembly according to those characteristics. Therefore, when the automatic transaxle assembly, or TCM has been replaced, it is necessary to reset the memory so that the TCM can memorize the new information. Reset procedure is as follows:


a.

Move the shift lever to N or P.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Utility / A/T Code Reset.

Powertrain > ECT > Utility
Tester Display
A/T Code Reset
50005 235 209

g.

Press "Next" again to proceed.

NOTICE:

After the transaxle compensation code is initialized, perform the following "Reset Memory" and "Perform Road Test to Allow TCM to learn" steps.



h.

Press "Exit".



PERFORM ROAD TEST TO ALLOW TCM TO LEARN


NOTICE:

Perform the following procedure while strictly observing all traffic laws and speed limits.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Data List / Throttle Position from EFI.

Powertrain > ECT > Data List
Tester Display
Throttle Position from EFI
50003 235 87

g.

From a standstill, achieve highest possible speed with the accelerator pedal opened 15% or less. Keep the accelerator pedal angle steady while driving the vehicle.

HINT:

"Throttle Position from EFI": 15% or less



h.

Repeat the previous step until shift shock no longer occurs.


i.

From a standstill, achieve highest possible speed with the accelerator pedal opened 25% to 35%. Keep the accelerator pedal angle steady while driving the vehicle.

HINT:

"Throttle Position from EFI": 25% to 35%



j.

Repeat the previous step until shift shock no longer occurs.



RESET MEMORY


NOTICE:

Reset Memory can be performed only with the intelligent tester.


HINT:

The TCM (ECT) memorizes the vehicle conditions when controlling the automatic transaxle assembly and engine assembly.

Therefore, when the automatic transaxle assembly, valve body assembly, shift solenoid valve SL3, shift solenoid valve SL4, or TCM has been replaced, it is necessary to reset the memory so that the TCM can memorize the new information.


a.

Reset procedure is as follows.

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the intelligent tester on.


v.

Enter the following menus: "Powertrain / ECT / Utility / Reset Memory". Then, press "Next".

NOTICE:

After performing Reset Memory, be sure to perform "Perform Road Test to Allow TCM to Learn" described earlier.


Powertrain > ECT > Utility
Tester Display
Reset Memory
50005 235 101